• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Pulling hard to left when braking

Jason72Bronco

Full Member
Joined
Feb 16, 2015
Messages
156
I finally have my Bronco project up and running, now for test drive.
When I brake, the Bronco pulls hard to the left.
I had already inspected, clean all brakes, and pads and drums look good. Did full brake bleed until I have clear fluid and firm pedal.
I tried to adjust the left and right brakes ("loosened" the left and "tightened" the right), but it is still pulling hard left when braking.
The only thing I can think is bad brake lines, but could it be something else?
Thanks,
Jason
 

Toddpole

Sr. Member
Joined
Jan 2, 2008
Messages
832
Drum or disc? If disc, and it's been sitting awhile, the right caliper may be seized giving full braking to the left and zero to the right. I had a cheby do this to me. That was a sporty little drive.
 

suthernboy

Sr. Member
Joined
Feb 16, 2010
Messages
422
Loc.
Greenville, NC
When I brake, the Bronco pulls hard to the left.
I had already inspected, clean all brakes, and pads and drums look good. Did full brake bleed until I have clear fluid and firm pedal.
I tried to adjust the left and right brakes ("loosened" the left and "tightened" the right), but it is still pulling hard left when braking.
The only thing I can think is bad brake lines, but could it be something else?
Thanks,
Jason

If you are adjusting them, I'm assuming you have front drum (but you said "pads" instead of the more correct & common "shoes"). If you bled them "clear" I'm assuming right front bled fine, so your hose should be OK. jack up the RF and spin the tire manually and get a friend/buddy/very smart dog/wife/girlfriend to apply the brake. See if the shoes engage and the wheel stops. With brake applied see if you can spin the wheel by hand. If you can, remove the drum and check all components to make sure they move freely, take your self-adjuster off and apart (3-pieces) and apply white lithium grease (or equivalent) to the inside surfaces, make sure the cable is in place, manually adjust the shoes until the drum just fits back on and you can spin it but with resistance. Test drive.
 

suthernboy

Sr. Member
Joined
Feb 16, 2010
Messages
422
Loc.
Greenville, NC
Oh, btw, if you DO have front disc, you're screwed. Caliper is most likely sticking and will need to be replaced or rebuilt. There is a recent post in the tech articles forum explaining how to rebuild for very little money.
 
OP
OP
Jason72Bronco

Jason72Bronco

Full Member
Joined
Feb 16, 2015
Messages
156
I have drums. Both sides will spin and stop when brakes are applied. I'm wondering if maybe the old rubber lines on the left are toast and are spongy enough that pressure is not maintained. I had a similar issue with my 53 Chevy, and new lines fixed it. This Bronco sat for nine years. I was curious if any suspension issue would cause the pulling.
 

savage

Bronco Nut
Joined
Apr 18, 2007
Messages
2,483
Loc.
Renton
Yes worn out ball joints, tie rod worn, wheel bearings. Are the drums new or did you have them resurfaced?
 

Seventee

Contributor
Sr. Member
Joined
Dec 7, 2012
Messages
999
Loc.
In the sticks of MT
Double check your wheel cylinders. I had a nasty left pull and discovered that one piston in the passenger side was completely siezed.
 

suthernboy

Sr. Member
Joined
Feb 16, 2010
Messages
422
Loc.
Greenville, NC
I have drums. Both sides will spin and stop when brakes are applied. I'm wondering if maybe the old rubber lines on the left are toast and are spongy enough that pressure is not maintained. I had a similar issue with my 53 Chevy, and new lines fixed it. This Bronco sat for nine years. I was curious if any suspension issue would cause the pulling.

Hmmm...I hadn't thought about that...the only failure mode I've experienced with hoses has been rupture. I suppose, as far as suspension goes, C-bushings and/or radius arm bushings that are in very poor condition could allow the axle to shift rearward under braking, but if they were that bad I'd assume there would be steering issues at all times, not just during braking. You have manually adjusted both fronts with drums removed to approximate equal resistance when spinning?
 
OP
OP
Jason72Bronco

Jason72Bronco

Full Member
Joined
Feb 16, 2015
Messages
156
The brakes were redone just before it was parked, so the pad and drum surfaces look good, and no leaky cylinders. I did do a complete new brake job on right rear due to failed axle seal that coated it in oil. Considering how long it sat, new slave cylinders might be a good idea anyway.
Next step needs to check bushings.
 
OP
OP
Jason72Bronco

Jason72Bronco

Full Member
Joined
Feb 16, 2015
Messages
156
Suthernboy, yes when I went through the brakes initially I adjusted all brakes to same resistance. Adding more resistance to the right helped a bit, but still pulling left.
 

spap

Bronco Guru
Joined
Jan 2, 2010
Messages
2,642
If you have a sticky front caliper I wouldn't even bother trying to fix it just buy new ones they are only like 25, 30 bucks ea
 

suthernboy

Sr. Member
Joined
Feb 16, 2010
Messages
422
Loc.
Greenville, NC
Suthernboy, yes when I went through the brakes initially I adjusted all brakes to same resistance. Adding more resistance to the right helped a bit, but still pulling left.

OK, so you're confident your components behind the drum are working freely as designed (and I'm assuming you did remember to add a dab of high temp grease, I use never-sieze, on the 4 points on the backing plate where the back edge of the shoe makes contact with the plate). And, both L & R drum surfaces are nice and smooth.

Yep, next thing I'd check is those bushings and as savage stated the ball joints, focusing on the driver side. I'd jack it up, remove the wheel, and take a long pry bar or length of pipe (not PVC;D) and try moving the axle at different points and directions and check for any unusual or excessive movement.
 

Bucky66

Contributor
Sr. Member
Joined
Jun 20, 2010
Messages
559
I had this problem once and realized I had a broken front braked retracting spring that retracts the shoes after the brakes are released. The problem was that the spring was broken which allowed that side to let the brake shoes engage way before the other side that had the spring. This held the shoes in a little while until the broken spring side engaged enough to let the other side have enough pressure to press the shoes out. I hope I explained this clearly.
This is the link to the replacement spring.


http://shop.broncograveyard.com/mobile/Front-Brake-Retracting-Spring/productinfo/12566/
 
Top