• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Rocker Arm Stud Nut Install

airbur

Bronco Guru
Joined
Jun 3, 2008
Messages
2,763
Loc.
Castle Pines, CO
Installing my newly rebuilt OEM 302 heads tonight. Reading the Ford maintenance manual, it shows only a torque value for the rocker arm stud nuts (17-23lbs). From what I have read, the proper way to adjust rockers is to tighten just until the pushrod takes a little effort to turn, then about 1/2 turn more. Which process do I use? I'm tending toward the Ford process as it's all OEM parts...heads, pushrods, lifters, rocker arms etc.

When I removed them, I measured the length of the threads on each stud above the nut and every one was 1/2".

Thanks.
 

Attachments

  • download.jpg
    download.jpg
    125.3 KB · Views: 168

rynos72

New Member
Joined
Dec 14, 2008
Messages
14
I re torqued mine at 18 ft lb, got about 300 miles and they are still quiet, i felt better about going with OEM standards.
 

broncnaz

Bronco Guru
Joined
May 22, 2003
Messages
24,342
Most factory 302's are non adjustable just torque and go. Push in positive stop studs with rail rockers arms are not adjustable
 

Desert Dweller

Sr. Member
Joined
Jan 20, 2011
Messages
381
Loc.
Central WA
Do you see the shoulder on the rocker stud? That means that you have non-adjustable rockers. So, torqueing them as the manual says is correct. :cool:
 

TwoDalesDad

Bronco Guru
Joined
Jul 19, 2011
Messages
1,515
On a small block ford engine tighten like this...make sure the pushrod is seated..then with your thumb and forefinger roll it back..and forth..tighten..just a little more..where she's snug....NoMORE...NOLESS....when you hold the skinny pedal on the floor....for any real legnth of time....the press in studs will lift out of the hole...which will mean a loss of power....and God forbid...the pushrod will get jammed through a piston....NO Way....JB WELD...will not help.
 
OP
OP
airbur

airbur

Bronco Guru
Joined
Jun 3, 2008
Messages
2,763
Loc.
Castle Pines, CO
On a small block ford engine tighten like this...make sure the pushrod is seated..then with your thumb and forefinger roll it back..and forth..tighten..just a little more..where she's snug....NoMORE...NOLESS....when you hold the skinny pedal on the floor....for any real legnth of time....the press in studs will lift out of the hole...which will mean a loss of power....and God forbid...the pushrod will get jammed through a piston....NO Way....JB WELD...will not help.

Yep...that is how I was shown (Bad Ass Engines video), but these are OEM and non adjustable so I wasn't sure. Sounds like the torque-and-go process as Ford prescribes is best.

Got the rockers on and the intake set.....

Thanks!
 

Attachments

  • photo.jpg
    photo.jpg
    130.1 KB · Views: 145

RG75Bronco

Jr. Member
Joined
May 23, 2010
Messages
141
Loc.
Jacksonville
While we are on the topic I have a question. When I had my 1975, 302 rebuilt I installed GT40P heads and used the stock push rods. Adjustable or non-adjustable? I adjusted the rockers to OEM specs. Thanks for input.
 

bmc69

Contributor
Bronco Guru
Joined
Jun 11, 2004
Messages
12,015
On a small block ford engine tighten like this...make sure the pushrod is seated..then with your thumb and forefinger roll it back..and forth..tighten..just a little more..where she's snug....NoMORE...NOLESS....when you hold the skinny pedal on the floor....for any real legnth of time....the press in studs will lift out of the hole...which will mean a loss of power....and God forbid...the pushrod will get jammed through a piston....NO Way....JB WELD...will not help.

Never, ever is that the correct procedure with the non-adjustable rocker setup. All you will do then is leave them loose to quickly back off...wherupon bad things can happen.;)
 

broncnaz

Bronco Guru
Joined
May 22, 2003
Messages
24,342
While we are on the topic I have a question. When I had my 1975, 302 rebuilt I installed GT40P heads and used the stock push rods. Adjustable or non-adjustable? I adjusted the rockers to OEM specs. Thanks for input.

non adjustable there as well. the only factory heads that came with adjustable valve train were pre 1970 might even be 69 heads and even a lot of those were not adjustable
 

bluesbish

Full Member
Joined
Jan 30, 2011
Messages
278
Loc.
Upstate New York
....and God forbid...the pushrod will get jammed through a piston....

How is this even possible? I know a lot about engines and I can't really think of any way the push rod can go through the top of the piston.
 
OP
OP
airbur

airbur

Bronco Guru
Joined
Jun 3, 2008
Messages
2,763
Loc.
Castle Pines, CO
How is this even possible? I know a lot about engines and I can't really think of any way the push rod can go through the top of the piston.

ROFL....I was thinking the same thing when I read that....but figured he new something I didn't:) Anything is possible!
 
Top