• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Rocker arm stud nuts

Scott C.

Sr. Member
Joined
Oct 10, 2009
Messages
667
Loc.
Waynetown IN
Cool!! You are lucky. You must have drawn moisture into it from condensation. If you put the piston at TDC on the compression stroke. You can tighten down the rocker arm until it contacts the pushrod. Do this by turning the push rod with one hand while you tighten the nut until you feel tension. That is zero lash. Then tighen an aditional 3/4 turn.
On your stud hiegths. Did they replace those taller studs? They should all be the same hiegth. They are just a press fit. You should be able to drive them down to the same heigth as the others. Just be careful to protect the threads. If they are loose and pulling out that is problem. I think you can buy over size studs to tighten up the press fit. It is the same stud as a small block Chevy. Is the one on the stuck valve one of the higher ones? It may have pulled out do to the stuck valve. That would lead me to look at the other valves to make sure that they are free.
 

.94 OR

Contributor
Bronco Guru
Joined
Jul 5, 2009
Messages
2,215
Loc.
Willamette Valley, OR
No, the stud on the stuck valve seemed fine. When I got them back from the machine shop they were that way. I didn't have a press at that time or I would have tried to push them in further. They feel super tight but figure I will watch them over time and see if they move. Otherwise, I am using a 3/8" washer under the nut so I can hold the rocker down where it needs to go.

The air chuck was pretty easy to make if you ever need one. Grind the ground strap off the plug, then grind the pinched edged above the ceramic off. Punch the ceramic out of the plug. I used a female threaded air nipple so I could round the outer edges (6 sides for the hex) off to fit in the spark plug base. Once I had a fit I liked, slightly tapered, I added some solder flux and pressed the two parts together in the vise. Heat up with a torch and add solder. Let cool and use.
 

Scott C.

Sr. Member
Joined
Oct 10, 2009
Messages
667
Loc.
Waynetown IN
When the machine shop cleaned the heads did they use an oven and heat the heads up and them put them in a shot tumbler? They would come out looking new. That could have cuased the studs to loosen and move while the head was heated up. Or, were the heads cracked and welded? That causes the same thing, but also makes the studs brittle and prone to break. They used to drill and pin the studs after welding cracks. That not really successful because they still broke ocasionally. Or, were studs already higher before the valve job? Maybe some on in the past has changed them out and did not get them in as deep as the others?
 

.94 OR

Contributor
Bronco Guru
Joined
Jul 5, 2009
Messages
2,215
Loc.
Willamette Valley, OR
Too many questions that I can't answer.

If I remember, the heads did have some cracks in them, as I remember thinking I was going to have a hard time finding replacements short of buying new aluminum heads. Anyway, they seem pretty tight, if I can tell anything. I'll keep an eye on them and see if they let the rockers slack off.

Just got home with my replacement plug, so I need to go see if it will run again. :p
 

Scott C.

Sr. Member
Joined
Oct 10, 2009
Messages
667
Loc.
Waynetown IN
I bet they heated them up and welded the cracks. That makes it all make sense. I think I would drive them back down. Screw a couple of nuts on them and jam them together with the top nut sticking up above the stud a few threads and drive them down with a hammer. Then remove the nuts and you should be good to go. That will let put mind at ease. If they move down too easy, they will need to be replaced.
 

broncnaz

Bronco Guru
Joined
May 22, 2003
Messages
24,342
If the heads were cracked and fixed and the studs are pulling I would really consider just getting replacements and ones with screw in studs. 302/351 heads are not hard to come by. I've never really heard of any cracking issues with SFB heads if yours were cracked then again I would highly consider replacements.
If the stud is pulled dont bother trying to beat it back down it will only pull again. You need a new stud or at the very least you need to pull it and reinstall with some retaining compound to ensure it stays in place.
 

Scott C.

Sr. Member
Joined
Oct 10, 2009
Messages
667
Loc.
Waynetown IN
Back in the day, when they were welding a lot cracked heads it was very common for that to happen during the repair process. They would get the heads too hot while heating and welding the cracks. I do agree, the best thing to do is discard the welded heads. As I stated in a previous post there where a lot of problems with studs in welded heads. I also saw a lot of welded heads that worked just fine. I think it all depends on the guys doing the work. Just like everything.
I ran a machine shop for 13 years. I did not do the welding. I never liked the whole idea of it. I did send heads of to be welded, but soon stopped that, do the stud problems. The repairs them selves almost always worked fine. I do remember one that still leaked afterwards and that led to more problems with the repair company and my customer. But, back in those days your options were very limited as was the customers money.
 

.94 OR

Contributor
Bronco Guru
Joined
Jul 5, 2009
Messages
2,215
Loc.
Willamette Valley, OR
How much pressure would it take to drive them in, or pressure to pull them out?

I have a 12 ton press, but I'm not excited about pulling the heads back off... I know, may be the best option, but I was hoping to get the thing running.
 

broncnaz

Bronco Guru
Joined
May 22, 2003
Messages
24,342
If all the studs are currently level then they are not pulling out. Replacing the studs can be done with the heads installed usually oversized studs are availible to replace ones that have pulled. If you hammer a pulled stud back in it will just pull back up as its already loosened from being pulled in the first place. thats why at the very least I would pull the stud completely and reinstall with retaining compound to ensure it stays, Oh sure you might get lucky and it might hold for awhile but once loose it will loosen again without proper replacement. Best option if the studs are pulling and the heads are ok would be to pull all the studs and install screw in type studs. This can also be done with the heads installed although not usually recommended as lost of metal shavings are made during the process.
 

Scott C.

Sr. Member
Joined
Oct 10, 2009
Messages
667
Loc.
Waynetown IN
The studs are not all that tight. You can drive them in with a 16 or 20 oz hammer pretty easy. Pulling them is a little tougher unless the press fit is disturbed. They make a tool for that. It can be done with a stack of washers or a short pipe nipple and a nut. just oil the bearing surface up to reduce friction. The studs most likely moved while the heads were very hot during the welding process. That being the cause, it should not affect the press fit. The head expands when heated and loosend the press fit. When cooled back down it shrinks back to size.
It has been over 15 years since I got out of the rebuild bussiness. It is not the same bussiness today. You would be surprised at the repairs that we did for new under warranty cars and tractors back then for the dealer ships. The mentality was to repair existin parts. Today it is replacement parts. A new head casting back in the late 70's and early 80's was very expensive. In the $400-$600 range. That was alot of money back then. Today you can buy new heads for less money.
 

.94 OR

Contributor
Bronco Guru
Joined
Jul 5, 2009
Messages
2,215
Loc.
Willamette Valley, OR
On a side note, I had one lifter spit out a couple parts which were laying in the oil galley. That is what prompted the cam/lifter change. Anyway, I took that lifter the rest of the way a part, and then re-assembled. The whole thing looked great despite its 40 years of age, but the part that concerned me, was the little spring wire that holds the guts in. It had been wearing on the underside where the push rod cup would slap up against it every time it would expand. I can't say for sure how much longer any of them would have held up, but I could see these fatiguing over time and failing.
 

broncnaz

Bronco Guru
Joined
May 22, 2003
Messages
24,342
Internally Lifters rarely show much wear. Figure for the most part they have constant oil pressure and no real wear points at least not on the inside.
 
Top