Smooth Street Bumpers from 2 Brothers Broncos

[JefeAZ]

Came across these guys(@2BrothersBroncos) a few months ago and they are making these street bumpers out of 1/8" steel. I think they look amazing. Not sure how they mount but $800/pair for raw finish plus shipping. Phone is 530-339-6685. If I didn't have bumpers ready I would have gone this route

 

[tatersalad]

Nice looking bumpers

 

[rydog1130]

Those are pretty slick

 

[Scoop]

They look good. Are they the same front and rear?

 

[sprdv1]

Very nice... Thanks for sharing

 

[No Hay]

I like these too. Clean lines look good. If my factory bumpers ever get replaced, and no winch, it would be this style.

 

[rguest3]

Kinda looks like a Protofab Bumper.

Here's a pic of my 76 with a Protofab rear. Optional Receiver Hitch and D-Ring mounts were added.

 

[bronconut73]

Are they called "street bumpers" because they are 1/8" thick?
I wondered at one point how much lighter a steel plate bumper would be if it was made with a little thinner plate. But maybe creatively gussetted to have near the strength of the 3/8" plate steel bumpers.

 

[JefeAZ]

They look good. Are they the same front and rear?

Looks like it

Are they called "street bumpers" because they are 1/8" thick?
I wondered at one point how much lighter a steel plate bumper would be if it was made with a little thinner plate. But maybe creatively gussetted to have near the strength of the 3/8" plate steel bumpers.

Ya they made sure to point out they are 1/8" thick and made for street Broncos. No lifting points and no hitch

Ya Id like to see how these mount and the weight savings.

Kinda looks like a Protofab Bumper.

They look similar but you can tell the differences. Heres my ProtoFab

 

[Glass Pony]

They look close to a Proto Fab but without the holes for the hi-lift jack. Here's my Proto Fab (non winch). It's 3/16" thick and has gusset welded in it across the top. My rear Proto Fab bumper with the tire carrier is 1/4" thick with gussets welded inside.
For an extra $50 more than the 2 Brothers you can get the Proto Fab's with the jacking holes. I guess it would depend where I lived as to shipping costs or if I could go pick it up.
https://protofab4x4.com/product/1966-1977-bronco-non-winch-flat-top-front-bumper/

 

[Scottysrods67]

There not Protofab my brother designed before protofab had any
We just started selling them again.

 

[Justin@WH4x4]

Hey Scotty, how do these mount? Do you have any pics for myself or the other guys on here that were wondering. Thank you sir!

 

[JefeAZ]

There are two vertically mounted plates that bolt into the factory holes. Then plate mounts to vertical plates welded to the bumper

Waiting on pics

 

[badkarma]

I cant see the original pics but am looking for a rear bumper. I may be going with cal creations.guess it was a block on office computer. Seeing them now.

 

[JefeAZ]

Here's the backside and mounts

 

[Jaarchers]

Did anyone ever get any pics of these bumpers? Is there a website to check them out?

 

[SteveL]

These were posted before. Nice except for the 1/8" part. May as well stick with a stock bumper.

 

[sprdv1]

Did anyone ever get any pics of these bumpers? Is there a website to check them out?

like in the first post? those pics?

 

[Pa PITT]

WOW Those are sweet looking bumpers . But i CAN'T LIKE WITHOUT A TRAILER HITCH.