Thread Name change > Clifford... Big Red Bronco

[904Bronco]

Easiest way to move the axle back 1" or 1 1/2" is to use Zero Rates. I've been running them for years without issue. They do add 1" lift to the axle. (Pretty sure this is the offset spacer DirtDonk mentioned.)

I know I bought these in the past... I still get email sales flyers from the company.
But I didn't use them for reasons I can't remember. And I don't know what became of them?
Thanks Scoop, for the option, actually the reminder...

 

[Oldtimer]

Doug,
When you use the offset holes in spring perch and clamp plate, you may need to add offset holes in the spring liners (if your springs have them), or you end up with this.

I also redrilled wedge.

 

[904Bronco]

Hi Doug, I used the same Ruff Stuff perches. The U bolt plate has matching offset spring pin holes. Here are a few pictures off my set up. And I think the plates are from James Duff.

That's what I needed to see, pictures tell the story.
I actually did a search on the Site and found enough commentary to see that the U-bolt plate would need to be offset as well. As you can tell this will be a first for me... I actually read through Duffy Mahoney's old thread when he did this mod on his 77.

I am hesitant to order those plate from Duffs, the shipping cost is terrible across the Country, but it remains an option.
Thanks for post Gnsteam.

 

[904Bronco]

I haven't bought springs yet, still scraping undercoating... But good to see that there is additional things that need to be done to do the change right. I am, admittingly AR about the things I do...

Would that be a WH's U-bolt plate? I was looking at them and thinking they could be re-drilled to work... Nice to see that the 6* wedges can still be used.

Thanks for sharing. OT

 

[Yeller]

Drill a corresponding hole in the bolt plate or buy a set with 3 holes.

 

[904Bronco]

Drill a corresponding hole in the bolt plate or buy a set with 3 holes.

Get the single hole plate, run a proper sized bolt through the center perch hole and the plate... then mark appropriate location and Drill...

Amazing how when you wake up in the middle of the night and your brain kicks into gear, what you think of...

 

[Yeller]

The distance to the now hole can be measured off the new spring perch too

 

[Oldtimer]

Would that be a WH's U-bolt plate? I was looking at them and thinking they could be re-drilled to work... Nice to see that the 6* wedges can still be used.

Yes, WH #1195, Extreme Duty Leaf springs U-bolt kit, modified

​

 

[ntsqd]

Dunno where you are in the process of removing the undercoating, but I have read of people hitting it with CO2 (presumably liquid, but don't know) and more or less freezing it loose. Supposed to be the cleanest, least labor intensive method known. If you have or know something with a CO2 tank & regulator it might be worth trying.

 

[904Bronco]

Dunno where you are in the process of removing the undercoating, but I have read of people hitting it with CO2 (presumably liquid, but don't know) and more or less freezing it loose. Supposed to be the cleanest, least labor intensive method known. If you have or know something with a CO2 tank & regulator it might be worth trying.

I think I am done with the frame. The easy to get to area's have been done and all that remains is areas of the factory welds that need cleaned out and/or areas I can't get to. It was a long day today and I basically filled a paper shopping bag with what was scraped off over the last few days.
A lot of the U-coating popped right off and the rest I had to work over.
Next I will separate the frame from the body do a tear down, and hit everything not touched with a scraper and wire wheel. It will be a week or so before I get back to it. Going to make a run up to Boise, ID for the Boise Roadster show and to visit Family and friends.

I had to sweep the floor this afternoon...

 

[Yeller]

Clean up is never the fun part. Have fun in Boise and tell Steve we are still enjoying the explorer it’s about to make a trip to Moab and enjoy its latest mods

 

[904Bronco]

Clean up is never the fun part. Have fun in Boise and tell Steve we are still enjoying the explorer it’s about to make a trip to Moab and enjoy its latest mods

Will do, he is on my list of folks to see... As is Justin, who is a salesman for WH's that works remotely there...

 

[sprdv1]

Drill a corresponding hole in the bolt plate or buy a set with 3 holes.

glad you still around giving sound advice that job must be smooth

 

[ntsqd]

If you make the Spring "plate" then you can put the hole wherever it needs to be.

FWIW those 'dry' lakes in the desert can be really caustic......

 

[904Bronco]

So just a few updates... Took a break and went to Idaho.

The Rebuilt power steer box showed up just before I left.
Good success looking through the wreaking yards, got that missing Explorer dipstick tube/d-stick that I needed. As well as many other pieces...
Found a factory dual battery tray (drivers side) for my 79 Bronco.
Got a call from my Buddy that my resealed D20 is ready for pick-up.
Stopped at Wild Horses on my way home and went into debt for new parts!
We are going to have heavy rain for the next few days, so not sure there will be a lot of shop time