• Just a reminder that you won't be able to start new posts or reply to existings posts in the Archive forum.

    This is where all the old posts go so they can still be used for reference and searched.
  • Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Windsheld frame question

cbfomoco

Bronco Guru
Joined
Jan 21, 2004
Messages
1,029
Loc.
WV
can any one say for shure if all 68 models had the screw on type windsheld frame? if it helps mine does have the removable door frames and did have the latch for the windshild. thanks
 

md_lucky_13

Sr. Member
Joined
Feb 20, 2004
Messages
371
Loc.
Idaho
Yes, they did.

All broncos had the option to have the front windshield fold down.

There are two large knobs on either end of the dash that hold it in place if you don't have a hard-top on (they should always be left there, even if you do have a hard top on)

If you want to fold it down, they unscrew, and, as long as it doesn't have a top bolted down, it will fold down on top of the hood.
 
OP
OP
C

cbfomoco

Bronco Guru
Joined
Jan 21, 2004
Messages
1,029
Loc.
WV
md_lucky_13 said:
Yes, they did.

All broncos had the option to have the front windshield fold down.

There are two large knobs on either end of the dash that hold it in place if you don't have a hard-top on (they should always be left there, even if you do have a hard top on)

If you want to fold it down, they unscrew, and, as long as it doesn't have a top bolted down, it will fold down on top of the hood.


that is not what i mean sorry what i ment was to take the whole frame off. at the hinge. i have heard that early modle broncos 66-68 had hinges that screw on insted of spot welds. I am trying to do plan ahead and wondering what i am planing for. thanks
 

md_lucky_13

Sr. Member
Joined
Feb 20, 2004
Messages
371
Loc.
Idaho
Ohhhhhh..

No, they don't.


What you are probably thinking about is the side WINDOW frames.

On the earlier models, the window frames could be removed with a couple of screws. That way, you could take out the entire side window frames, and the glass. It gives it a really clean look.

I may have a picture somewhere. I used to do it when I ran a Bikini top because it looked good.. But, it wasn't so cool when it rained, so I eventually put them back in.

I have never heard of a screw-off front windshield.
 

md_lucky_13

Sr. Member
Joined
Feb 20, 2004
Messages
371
Loc.
Idaho
If you can stand my ugly mug, this is what I'm talking about....
 

Attachments

  • trophy2.jpg
    trophy2.jpg
    100.7 KB · Views: 119

WPBronco

Jr. Member
Joined
Jan 31, 2005
Messages
53
Loc.
Hattiesburg, MS
I have a 1968 and have seen many people say that the windshield hinge can be unbolted allowing the entire windshield to be removed. After 1968 the hinges were welded and you have to remove the spot welds to remove/replace your windshield.

With that said, I have folded my windshield over and it looks as though my 68 windshield is welded in. So that may help you and maybe not. Of course I have one door that the door window frames unbolt and the other is welded in so I am not sure what my old Bronco has gone through before it reached my hands.
 

malcolmzilla

Bronco Guru
Joined
Mar 18, 2003
Messages
1,522
Loc.
Calgary, AB, Canada
My 68 tub had 1/4" NC threaded holes for the W/S hinge. However, the PO chose to use sheetmetal screws.

The W/S hinge had corresponding holes. The W/S I believe was newer as the spot welds on its side of the hinge had been pulled and it was lip/booger welded on.

I have replaced the hinge with a generic stainless one, drilled it using the old hinge as a reference, plug welded it to the W/S, and used real short tapered head 1/4" NC screws on the tub side of the hinge. Fits OK, closes OK.
 

WPBronco

Jr. Member
Joined
Jan 31, 2005
Messages
53
Loc.
Hattiesburg, MS
Well dang. Maybe I need to look at my hinge again. Are the bolt heads covered by anything or is it quite obvious when you fold the windshield over?
Would love to easily get that thing off since I have stripped out on of the windshield knobs ...#$&@#&%#....

Maybe I dont have a 68.....even though the VIN# on the glove compartment says so.......of course, maybe its not the original glove compartment door.

WHen I bought it a year ago, it had a 200 6 cylinder instead of a 170. The attachment of the door window frames are different for each door (dang it). It does have a T shift Dana 20 and a Dana 30 front end. Obviously someone has done some work on it or the factory made it from leftover 68 parts and new 69 parts.
 

Bronconut

Full Member
Joined
Jun 15, 2002
Messages
278
Both of my 68's have bolt on windshield frames. And yes, from what I can tell between my 2. Ford mixed parts from years.. I have an early and late build 68 and they have some pretty big differences.
 
Top