• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Hydroboost/ram assist?

TOFIC

Bronco Wrencher and Fixer
Joined
Jan 6, 2004
Messages
3,740
Loc.
Redcliff Alberta
Great responses guys - Not looking forward to the triple digit bill of having the boost unit ported for flow.

Why have the boost unit ported?? Triple digit?? Man, who is doing that? WAY to much for a simple port job. I have done the port job on 2 or 3 hydroboosts and it is really simple. As to the saginaw read the write up on West Texas sight for the methods of boosting that pressure and flow. (BE CAREFUL, it can be messy!! ask me how i know)
Your hydroboost will work just fantastic, unless you are running some really monster meats on your Bronco. 38's or bigger is where I get concerned but the one ton units dont have problems with these.
TOFIC
 

KyleQ

Bronco Guru
Joined
Apr 24, 2008
Messages
5,480
Why have the boost unit ported?? Triple digit?? Man, who is doing that? WAY to much for a simple port job. I have done the port job on 2 or 3 hydroboosts and it is really simple. As to the saginaw read the write up on West Texas sight for the methods of boosting that pressure and flow. (BE CAREFUL, it can be messy!! ask me how i know)
Your hydroboost will work just fantastic, unless you are running some really monster meats on your Bronco. 38's or bigger is where I get concerned but the one ton units dont have problems with these.
TOFIC


Vanco over on Pirate is offering up a service to port (100 bones) and rebuild (180 bones) your boost unit so it will flow enough GPH's to run a hydro ram. I would love some info on porting a hboost unit - I'n not afraid to tinker with that thing.
I've got a Sag pump out of a 90's van that I had intended on putting in my pickup, hopefully I can swap the serp pulley off it for a v pulley and do the pressure mod. I plan on running 37" boggers on this Bronco, so the 78' steering gear is in order with the 2wd worm gear swap.
Anything you would suggest? I'm opting for the Stage II through West Tex so I can have the box rebuilt and get the ram with the hoses. I've got the Astro boost, MC, most hoses (cut) and the external resivore.
 

TOFIC

Bronco Wrencher and Fixer
Joined
Jan 6, 2004
Messages
3,740
Loc.
Redcliff Alberta
I would love some info on porting a hboost unit - I'n not afraid to tinker with that thing.
I've got a Sag pump out of a 90's van that I had intended on putting in my pickup, hopefully I can swap the serp pulley off it for a v pulley and do the pressure mod. Anything you would suggest?

porting a Hboost is not difficult just different. Not difficult either.
I would not do the pressure mod in your case. Unless WTO strongly recommends it but a black pressure spring in the pump and call it good.

Drop me an email (walker@agt.net) and I will fill you in on the improving the hboost unit. way too much to be said for the thread.

TOFIC
 

Mark

Contributor
Bronco Klutz
Joined
Aug 29, 2003
Messages
5,417
Loc.
NW Indiana
Drop me an email (walker@agt.net) and I will fill you in on the improving the hboost unit. way too much to be said for the thread.

TOFIC

That's what the thread is for. What can't be said in the thread that can be said via email?
Don't bogart good information TOFIC.
Come on, out with it. We all want to know.
 

KyleQ

Bronco Guru
Joined
Apr 24, 2008
Messages
5,480
I'll write up an article when I do mine - if that is ok with TOFIC. If not - he can write up another one of his excellent articles...
 

KyleQ

Bronco Guru
Joined
Apr 24, 2008
Messages
5,480
That link is geared towards improving the pump. From what I read TOFIC is referring to modifying the hydroboost unit so that it has less restriction when installed in sequence with the PS box for ram assist.

Yup - hboost units are not designed to flow fluid, so trying to run a hydro ram after one is a little tougher then just installing a hboost unit.
 

TOFIC

Bronco Wrencher and Fixer
Joined
Jan 6, 2004
Messages
3,740
Loc.
Redcliff Alberta
hydroboost "porting"

OK OK quit nagging!!! here is the short version on improving an hydroboost unit.

The following items I am going to assume you already have:
A good hydroboost, out of the truck.
A Saginaw power steering pump, preferably a one ton unit
Dual returns on the pump body.
Good large pressure lines.
We are going to deal with the HBoost only!! the pump is another issue
Remember, HBoost is parasitic, and only uses fluid pressure when it is in use

Now lets deal with the "porting", tuning would be a better word.
Take the unit apart completely and we are dealing with the main body with the three ports on it. We take it apart to keep things clean and believe me a small sliver of metal in the spool valve area of the HBoost will permanently destroy the unit. CLEANLINESS is the word here.
Now, we want to increase the size of the high pressure ports at least a little larger than stock. take your unit and measure the ID of the high pressure port from the pump. take this measurement and get a drill bit one size bigger than this measurement and drill out the port carefully. Do not score the inside of the unit as this will definitely ruin your day and unit. I have gone two drill sizes with inverted flare units but bubble flare is not as forgiveing and one size is all they can stand. drill it out slowly and smoothly so you get a smooth channel. trick here is to ensure the port on the inside of the unit is smooth as a babies bum because roughness will cause the seals to rip and you will learn how to rebuild a unit quickly. clean and smooth are the words.
Do the same with other high pressure port again careful you do not score the inside of the unit or you will be looking for another body.
Now the Low Pressure return or as they say the pressure bleed port.
This one I threaded for a large fitting, I went significantly larger because of the fitting I used. match the size of the fitting (ID of the fitting) and drill this out on the body. Again don't score the valve area.
Put your LP fitting on and ensure it stays on and seals I usually epoxy mine onto the unit.
wash the body and wash it again. if its not clean enough to eat off its not clean enough. Mine went into a large boiling pot with the cleaning mixture in it (even amounts of water and varsol with Cascade dish washing soap added) boiled to death for 1/2 hour. OUTSIDE guys this mixture is potent.

assemble the unit and this will handle just about anything you throw at it.
The super duper ultra magnum killer mod setup has other tricks used on it and cost a lot of money to do but you will not need that one unless you are running 44's on rockwells or similar such ilk.
TOFIC
 

SC74

Contributor
Bronco Guru
Joined
May 24, 2004
Messages
3,472
Good Info - I'm going to remember this for a future mod. Thanks for the info!
 

KyleQ

Bronco Guru
Joined
Apr 24, 2008
Messages
5,480
Ok - so last weekend I thought I should tear down and clean my hboost unit. This thing was a pig, just dirty. I cracked the unit in half, pulled the guts, put it back together and started cleaning it with brushes and lacquer thinner.
DSCI0146.jpg
After taking it apart and trying ever so hard to get a good picture of one of the ports I gave up and ended up with this picture.
3 steps.jpg
The high pressure ports have a threaded area (blue) that necks down slightly (green) where I think the seal is actually made and then drops down about 3/8" and then gets smaller (red). What part do you drill out? You mention measuring the size of the pump output - do you remember what drill bit size you used? I do not have a pump yet - and I'm not about to make a giant mess by tearing apart my working and driving Bronco...
 

TOFIC

Bronco Wrencher and Fixer
Joined
Jan 6, 2004
Messages
3,740
Loc.
Redcliff Alberta
take the drill bit index and start putting them into the port (red area) until you find the one that fits. If this is a inverted flare unit, go up 1/32 of an inch bigger bit and drill this out. If this is a bubble flare outfile go up 1/64 of an inch bigger and drill it out.l this will up the flow but lessen the pressure to the unit. If you want to up the pressure you will have to alter the PS pump to get this.
TOFIC
 

TOFIC

Bronco Wrencher and Fixer
Joined
Jan 6, 2004
Messages
3,740
Loc.
Redcliff Alberta
cute outfit for cleaning!! I like my method. one of those turkey deep fryers that are propane powered.. in the can i put a mixture of varsol and water and a couple of Cascade dishwasher tabs. Cleans anything right up to spiffy.
Cheap too. got the cleaner for 20 bucks at a tag sale with the tank!!
TOFIC
 

KyleQ

Bronco Guru
Joined
Apr 24, 2008
Messages
5,480
cute outfit for cleaning!! I like my method. one of those turkey deep fryers that are propane powered.. in the can i put a mixture of varsol and water and a couple of Cascade dishwasher tabs. Cleans anything right up to spiffy.
Cheap too. got the cleaner for 20 bucks at a tag sale with the tank!!
TOFIC

Ha - carheart shirts and jeans are what I wear in the garage. I was wearing the mask, goggles and later on gloves because the solvent I was using was making me higher then a kite :-X

So drilling out the holes - am I going to only be drilling them out 1/32 or 1/64 of an inch or an I finding a bit that will fit on top of that drop down area where it necks down and then drill that 1/32/64s bigger?

Just a little confused because 1/32 or 64th doesn't seem like it would improve flow at all, so I'm assuming you want me to drill out that lower restriction completely so it doesn't neck down before the hose.
 

TOFIC

Bronco Wrencher and Fixer
Joined
Jan 6, 2004
Messages
3,740
Loc.
Redcliff Alberta
So drilling out the holes - am I going to only be drilling them out 1/32 or 1/64 of an inch or an I finding a bit that will fit on top of that drop down area where it necks down and then drill that 1/32/64s bigger?

Just a little confused because 1/32 or 64th doesn't seem like it would improve flow at all, so I'm assuming you want me to drill out that lower restriction completely so it doesn't neck down before the hose.

Do not drill out the sealing area!! You will be in your "cute" outfit again cleaning a new unit if you do. I agree the amount you drill out appears not to be much but in the overall picture it does work. you can drill bigger but be careful!!! to much and you have a pressure leak!!! Not a great idea, as you will be looking for another unit.
ONLY open up the flow area which is the small hole.
TOFIC
 

KyleQ

Bronco Guru
Joined
Apr 24, 2008
Messages
5,480
Do not drill out the sealing area!! You will be in your "cute" outfit again cleaning a new unit if you do. I agree the amount you drill out appears not to be much but in the overall picture it does work. you can drill bigger but be careful!!! to much and you have a pressure leak!!! Not a great idea, as you will be looking for another unit.
ONLY open up the flow area which is the small hole.
TOFIC

Alright - I'll drill it and put it back together. There wasn't any sealant holding the unit together - do I need to use any? The 5 bolts that held it together were super tight - is that rubber seal on the piston side of the unit the only thing that keeps the high pressure fluid inside the unit?

I'm going to go to the yard when I have time a grab a few of these units - they are decently easy to pull and they are cheap.
 

67broncorebuild

Sr. Member
Joined
May 29, 2008
Messages
426
Loc.
stanwood Wa
I am going hydro boost, and ram assyst. I dont have a power steering box yet, so i am buying the West coast broncos' ram assyst box. The ram assyst is hooked through the p/s box. The pump dosent have to work that hard for the hydro boost,(works hardest through box). I will use a cooler for the return line to pump, and was told to me everything will work fine, with no problems.
 
Top