• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

steering questions - ram assist

74BroncoCO

Bronco Guru
Joined
Nov 3, 2004
Messages
2,378
My track bar drop bracket jacked up my frame can-opener style over the weekend when it folded under load:
P3080041.jpg


P3080042.jpg


So the plan is to fix the frame, move the track bar much closer to the frame and forward and put a riser bracket on the axle. And ram-assist as well if I can swing it.

Here is what I have:
HP D44 from a 77 F-150, narrowed to EB width.
I have what looks like a 4" drop pitman arm now.
1 ton TRO tie-rod & drag-link.
Steering box is tapped & ready.
GLO diff-cover

here is my setup currently. The come-along and drag-link hides the track bar.
P3080040.jpg


I was fairly happy with my PS setup prior to this and never felt the need to do hydro-assist. However, adding a ram will take a lot of stress off the track bar and when I go to bigger tires, I may need the extra power. Also I want to try to design the system knowing that someday I want to make a y-link front suspension and the wedges will come off in favor of more ballistic bling.

My questions are:
1. Which ram? I am thinking a 1.5" x 8" stroke. Looks like PSC has some good prices.

2. where to mount? Off the track bar riser bracket or diff cover? If Diff cover, what should I do to make sure the cover stays on the axle housing?

3. Should I remove the drop pitman arm and replace with a flat one? That would make my drag link steeper and I'd have to account for that in the track bar.

4. bracketry; I don't have the tools to make nice looking ones. I have seen some from Ballistic, poly, etc, and I may be able to make some of those work, but are there other sources I can look at? All of the ones I have seen has the mounting hole way too far from the frame.

5. what are good places to measure from in order to make sure the axle is centered again before final welding?

I am sure I'll have more questions as you make suggestions, but this should get the brainstorming started. Thanks!

J.D.
 

BroncoDawg

Sr. Member
Joined
Mar 4, 2005
Messages
672
Loc.
Bishop, CA
I recommend mounting the ram from the Trac bar riser to the tie rod, but with a stout diff cover, have seen rams go from the cover to the tie rod succesfully.
Just read this am about a brother on Socal broncos destroying his WH tracbar riser and that is a first that I know of that happening. Don't think he has a ram either, so curious why it would fail, except that he wheels hard.

I believe adding ram assist will in fact put more load on the trac bar, not less.
The ram is trying to push the axle out from under the bronco and the trac bar and to some extent the steering box has to counter that energy.
Good idea shortening the drop bracket and gusseting it.

Have fun.
 

gravy

Bronco Guru
Joined
Sep 4, 2006
Messages
1,236
Loc.
Parsippany
My track bar drop bracket jacked up my frame can-opener style over the weekend when it folded under load:
P3080041.jpg


P3080042.jpg


So the plan is to fix the frame, move the track bar much closer to the frame and forward and put a riser bracket on the axle. And ram-assist as well if I can swing it.

Here is what I have:
HP D44 from a 77 F-150, narrowed to EB width.
I have what looks like a 4" drop pitman arm now.
1 ton TRO tie-rod & drag-link.
Steering box is tapped & ready.
GLO diff-cover

here is my setup currently. The come-along and drag-link hides the track bar.
P3080040.jpg


I was fairly happy with my PS setup prior to this and never felt the need to do hydro-assist. However, adding a ram will take a lot of stress off the track bar and when I go to bigger tires, I may need the extra power. Also I want to try to design the system knowing that someday I want to make a y-link front suspension and the wedges will come off in favor of more ballistic bling.

My questions are:
1. Which ram? I am thinking a 1.5" x 8" stroke. Looks like PSC has some good prices.

2. where to mount? Off the track bar riser bracket or diff cover? If Diff cover, what should I do to make sure the cover stays on the axle housing?

3. Should I remove the drop pitman arm and replace with a flat one? That would make my drag link steeper and I'd have to account for that in the track bar.

4. bracketry; I don't have the tools to make nice looking ones. I have seen some from Ballistic, poly, etc, and I may be able to make some of those work, but are there other sources I can look at? All of the ones I have seen has the mounting hole way too far from the frame.

5. what are good places to measure from in order to make sure the axle is centered again before final welding?

I am sure I'll have more questions as you make suggestions, but this should get the brainstorming started. Thanks!

J.D.


Sorry about the pics being sized down- its the only way I can upload them. Here is how I set mine up. One end to the WH riser bracket that I modified to use with the shortened HP 44. The other to the tie rod. This takes the 99% of the pressure off the box, frame and track bar since it is pushing only on the tierod attached to the axle. The draglink acts as a guide. This is the only way I recommend setting it up- 8in stroke is fine- make sure it is adjusted properly- the piston should bottom in both directions before hitting the steering stops.

For the track bar poly sells a universal upper bracket that would work once you fix the frame. I used a HD one that slides in and uses an additional bolt thru the frame but its not a big drop. The drop arm could be eliminated as long as the track bar angle is within a few degrees of the draglink- otherwise you will have some bump steer. It wont be as noticable with the power assist though.

Measure from the center of the tire to the frame on each side in the same location to get your center point.
 

Attachments

  • bronco 009.jpg
    bronco 009.jpg
    34.2 KB · Views: 177
  • bronco 010.jpg
    bronco 010.jpg
    35.2 KB · Views: 180

allenfahey

Bronco Guru
Joined
Mar 18, 2004
Messages
2,672
I'd get rid of that drop track bar bracket and fix your frame. Get a riser for the axle and contact Drew (Broncitis) on Classic Bronco's for this bracket. We installed this at the MEB Wrench and Roast along with my WH Riser and D60 front end. I too plan on a ram assist and the track bar brace he had made is good insurance:) I also have a stock pitman arm and the tie rod is on top of the D60 knuckles. The track bar and drag link are parallel to each other.
 

Attachments

  • P1040123.jpg
    P1040123.jpg
    121.2 KB · Views: 175
OP
OP
7

74BroncoCO

Bronco Guru
Joined
Nov 3, 2004
Messages
2,378
Broncodawg, read what Gravy says about the ram and how it acts on the steering. If you removed your drag-link and track-bar, the ram would still steer the wheels because it is acting only between the tie-rod and the axle. No additional forces are applied to the frame and steering box. I do appreciate your input. Although you don't want to remove your trac bar because the bronco could fall to the side just setting there. I have added two 10k lb straps in a criss-cross pattern from the frame to the axle so that when I take the track bar off, the bronco stays put.

Gravy - after looking at my setup more closely last night, it is nearly identical to what you have, but I don't have the high steer, so maybe I keep my drop pitman arm, but do everything else you did. My only concern is there doesn't appear to be enough room in there. But your ram is attached well past the diff cover and I think I'll have to do the same. I only have 7-3/8" throw. I would appreciate more pictures of your setup if possible and easy. I will PM you my email address.

allenfahey - thanks for the heads up on the bracket. It does look beefy, but I am not sure what all is part of the bracket. I will PM him and see.
J.D.
 

gravy

Bronco Guru
Joined
Sep 4, 2006
Messages
1,236
Loc.
Parsippany
The brace to the opposite side frame rail is the best way to strengthen the bracket. At the least have the bracket squeeze the frame- mine does this. The further you drop the bracket the more leverage it has on the frame, that why they break so easy- plus the frame is not strong to begin with. The people that run the assist cylinder on the dragling are putting a lot of stress on the box mount on the frame still. The goal is to move the steering power away from the frame so you dont break the mounts as you do without the assist. When you mount the cylinder to frame it will push the frame back and forth, now putting pressure on the track bar mount and continued stress on the frame at the box. The track bar mount has lots of stress on it already with the weight of the truck laterally pushing on it. Just my $.02
 

broncotime

Bronco Guru
Joined
Jun 30, 2003
Messages
1,188
Loc.
Grapevine, Texas
Broncodawg, read what Gravy says about the ram and how it acts on the steering. If you removed your drag-link and track-bar, the ram would still steer the wheels because it is acting only between the tie-rod and the axle. No additional forces are applied to the frame and steering box. I do appreciate your input. Although you don't want to remove your trac bar because the bronco could fall to the side just setting there. I have added two 10k lb straps in a criss-cross pattern from the frame to the axle so that when I take the track bar off, the bronco stays put.

Gravy - after looking at my setup more closely last night, it is nearly identical to what you have, but I don't have the high steer, so maybe I keep my drop pitman arm, but do everything else you did. My only concern is there doesn't appear to be enough room in there. But your ram is attached well past the diff cover and I think I'll have to do the same. I only have 7-3/8" throw. I would appreciate more pictures of your setup if possible and easy. I will PM you my email address.

allenfahey - thanks for the heads up on the bracket. It does look beefy, but I am not sure what all is part of the bracket. I will PM him and see.
J.D.


Please post the pictures on here if you get them. This is a mod I would like to do some time and that looks like a good set up.

Thanks
 
OP
OP
7

74BroncoCO

Bronco Guru
Joined
Nov 3, 2004
Messages
2,378
The brace to the opposite side frame rail is the best way to strengthen the bracket. At the least have the bracket squeeze the frame- mine does this. The further you drop the bracket the more leverage it has on the frame, that why they break so easy- plus the frame is not strong to begin with. The people that run the assist cylinder on the dragling are putting a lot of stress on the box mount on the frame still. The goal is to move the steering power away from the frame so you dont break the mounts as you do without the assist. When you mount the cylinder to frame it will push the frame back and forth, now putting pressure on the track bar mount and continued stress on the frame at the box. The track bar mount has lots of stress on it already with the weight of the truck laterally pushing on it. Just my $.02

Yep, that's why I am going from the axle to the tie-rod. Then it only stresses the parts that can handle it (1 ton TRE's).

Here is my plan of attack:

Cut out the damaged section of the frame, fill-in with 3/16” plate.
Plate the frame again with 3/16” everywhere I can.
Install this riser bracket on the axle as close to the c-clamps as possible (6” riser and offset forward)
Build a bracket off the above riser that will hold the stationary end of the ram
Install gussets from riser bracket to axle.
Modify this bracket so that the mounting position is as close to the frame as possible.
Buying a quality ram, mount it to the riser bracket and weld tabs onto the tie-rod.
Get the rebuildable hose ends and good hose and plumb it in.

My concern is the alignment of the trac bar to the drag link. I currently have a 4” drop bracket on the bronco now. That riser bracket is 6” so my trac bar will be 2” different on the passenger side than the drag link and I am not sure how much bump-steer that will cause. I also have a 4” drop pitman arm, so I could raise that, but from what I have seen, there is only a stock flat one or a 4” drop. I could figure out the difference in the angle after I take some measurement, but it won’t be much. I know the riser bracket is customizable, but I am not sure the $30 is worth it. Maybe they will work with me if I buy two brackets and a few tabs from them?

Whatcha think about that plan?

J.D.
 

gravy

Bronco Guru
Joined
Sep 4, 2006
Messages
1,236
Loc.
Parsippany
Yep, that's why I am going from the axle to the tie-rod. Then it only stresses the parts that can handle it (1 ton TRE's).

Here is my plan of attack:

Cut out the damaged section of the frame, fill-in with 3/16” plate.
Plate the frame again with 3/16” everywhere I can.
Install this riser bracket on the axle as close to the c-clamps as possible (6” riser and offset forward)
Build a bracket off the above riser that will hold the stationary end of the ram
Install gussets from riser bracket to axle.
Modify this bracket so that the mounting position is as close to the frame as possible.
Buying a quality ram, mount it to the riser bracket and weld tabs onto the tie-rod.
Get the rebuildable hose ends and good hose and plumb it in.

My concern is the alignment of the trac bar to the drag link. I currently have a 4” drop bracket on the bronco now. That riser bracket is 6” so my trac bar will be 2” different on the passenger side than the drag link and I am not sure how much bump-steer that will cause. I also have a 4” drop pitman arm, so I could raise that, but from what I have seen, there is only a stock flat one or a 4” drop. I could figure out the difference in the angle after I take some measurement, but it won’t be much. I know the riser bracket is customizable, but I am not sure the $30 is worth it. Maybe they will work with me if I buy two brackets and a few tabs from them?

Whatcha think about that plan?

J.D.

The plating plan sounds good and the upper bracket is the same one I was thinking- finish all this and then start the axle bracket and steering, you can change the pitman arm to move the draglink angle. The steering part and the lower bracket can almost be done at the same time so you can line things up.
I am not in love with the lower bracket- not alot of lateral support for just regular use, nevermind the ram pushing on it. With your style axle this one http://www.polyperformance.com/shop/Universal-Axle-Mount-Track-Bar-Bracket-p-1701.html would work out good- mount it up against the c-bushing mount as far as it can go towards the pass side- the longer the track bar is the better. More expensive but a better start and you can trim it to make it lower- this would get you lined up the draglink. If the track bar and the draglink are off more than 5-10 degrees you will feel since they are so short. Get it as close as you can.
 

Steve

Bronco Guru
Joined
May 5, 2003
Messages
2,986
Loc.
Grand Junction, CO
The people that run the assist cylinder on the dragling are putting a lot of stress on the box mount on the frame still. The goal is to move the steering power away from the frame so you dont break the mounts as you do without the assist. When you mount the cylinder to frame it will push the frame back and forth, now putting pressure on the track bar mount and continued stress on the frame at the box. The track bar mount has lots of stress on it already with the weight of the truck laterally pushing on it. Just my $.02

I have never seen a hydro assist cylinder mounted between the frame and the drag link. That would not be a smart way to go at all, but I've never seen or heard of anyone doing it.


J.D., I have that track bar riser bracket from Ballistic Fab for the D60 I'm putting under mine. I would not use that one with hydro assist connected to it. There's not enough lateral support IMO for that kind of use. I'd use the bracket from WH because of the lateral support it provides. The Poly Performance mount linked in a previous post looks like it would have good lateral support as well.
 

gravy

Bronco Guru
Joined
Sep 4, 2006
Messages
1,236
Loc.
Parsippany
I have never seen a hydro assist cylinder mounted between the frame and the drag link. That would not be a smart way to go at all, but I've never seen or heard of anyone doing it.


J.D., I have that track bar riser bracket from Ballistic Fab for the D60 I'm putting under mine. I would not use that one with hydro assist connected to it. There's not enough lateral support IMO for that kind of use. I'd use the bracket from WH because of the lateral support it provides. The Poly Performance mount linked in a previous post looks like it would have good lateral support as well.

I have seen a few. Even one of the WH trucks has it mounted like that or at least it did. You will notice it in the pictures. I run the WH riser modified- it worked out well.
 

Steve

Bronco Guru
Joined
May 5, 2003
Messages
2,986
Loc.
Grand Junction, CO
I have seen a few. Even one of the WH trucks has it mounted like that or at least it did. You will notice it in the pictures. I run the WH riser modified- it worked out well.

I've seen steering stabilizers from the frame crossmember to the drag link, so I guess I can see why someone might think an assist ram could go there. Not a good idea at all IMO.

I used the WH bracket as well for the hydro assist on my D44, which is now going under a rig in Seattle.
 
OP
OP
7

74BroncoCO

Bronco Guru
Joined
Nov 3, 2004
Messages
2,378
Gravy!!! That poly bracket is well....gravy!! I search that site for track bar and that DID NOT come up. But I do like it!! I was planning on putting gussets on the other bracket, but this will save me some time!!! Diggin it!

Steve, thanks for the input.

J.D.
 

gravy

Bronco Guru
Joined
Sep 4, 2006
Messages
1,236
Loc.
Parsippany
Gravy!!! That poly bracket is well....gravy!! I search that site for track bar and that DID NOT come up. But I do like it!! I was planning on putting gussets on the other bracket, but this will save me some time!!! Diggin it!

Steve, thanks for the input.

J.D.

I was going to use it but I already had the WH bracket from and old lp 44. I have a few of them at my shop for use on the custom set ups. They work out pretty good. Mike will probably answer the phone- Tell him Dave from Krazy House sent you.
 

Roadburner

Full Member
Joined
Mar 14, 2008
Messages
168
My boys and I installed the riser bracket on Alan's rig at the wrench & roast last year. It was similar to the ones I make. Mine nor the WH bracket fit the full size axle without modifications that the user would have to do for his specific needs. I have had customers mount a ram assist on the riser. When Alan's was installed, a backup bracket was fabed and was welded onto the axle behind the riser. The riser was then welded to this bracket and to the axle. When it was done it looked like a riser installed on a D44. Keep in mind he had a full width D60 and we used Cage arms on it, so we started with a bare axle and mounted everything where we needed .
 

bigjhoov

nobody
Joined
Apr 10, 2005
Messages
3,583
JD,

Here's what we're currently doing on Matt Chapman's rig. Not sure if it would work on yours since you have the TRO and ball joints. It's still in mock-up, that's why everything is loose.

S7302268small.JPG


S7302265small.JPG


S7302266small.JPG


S7302267small.JPG
 

broncotime

Bronco Guru
Joined
Jun 30, 2003
Messages
1,188
Loc.
Grapevine, Texas
Here's what we're currently doing on Matt Chapman's rig. Not sure if it would work on yours since you have the TRO and ball joints. It's still in mock-up, that's why everything is loose.

Jerry, Won't the Track Bar hit the RAM and the diff mount when the drivers wheel is pushed up into the wheel well? My track bar scrapes my stock diff cover when the front gets really twisted. At least I think that's what rubbed the powder coating off the track bar.

Glenn
 

JWMcCrary

Contributor
Bronco Guru
Joined
Oct 14, 2004
Messages
5,001
My track bar scrapes my stock diff cover when the front gets really twisted. At least I think that's what rubbed the powder coating off the track bar.

Glenn

Mine did the same thing until until I switched to a riser on the axle and removed the drop bracket.
 

Bronco Brian

Bronco Guru
Joined
Feb 10, 2006
Messages
1,140
If you want track bar BEEF on the frame I would look at the James Duff H/D track bar mount. It raps around the frame. You can cut it down to stock height so you don't bend your TRO. I put one on and a wild Horses axle mount and ran 37s with a ram.
 

bigjhoov

nobody
Joined
Apr 10, 2005
Messages
3,583
Here's what we're currently doing on Matt Chapman's rig. Not sure if it would work on yours since you have the TRO and ball joints. It's still in mock-up, that's why everything is loose.

Jerry, Won't the Track Bar hit the RAM and the diff mount when the drivers wheel is pushed up into the wheel well? My track bar scrapes my stock diff cover when the front gets really twisted. At least I think that's what rubbed the powder coating off the track bar.

Glenn


I don't think so Glenn. We maxed out the left front with a forklift and it was clear.
 
Top