• Just a reminder that you won't be able to start new posts or reply to existings posts in the Archive forum.

    This is where all the old posts go so they can still be used for reference and searched.
  • Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

rock sliders?

bigbri69

Sr. Member
Joined
Oct 7, 2007
Messages
421
Loc.
tomsriver
can someone post up on making your own rock sliders.thinking about doing it cause the po did some fiberglass work on them to cover rust put it dose not look so good..i can cut above the bad stuff and have about 1" of good meat to work with.i cant seem to find it.thanks
 

PHARMIE

Full Member
Joined
Jan 11, 2008
Messages
176
There are a few threads on the subject. I havent done this mod myself but I have seen many good threads on the topic that have a lot of info and details you could search for on here.
 

Dan74Bronc

Sr. Member
Joined
Feb 13, 2007
Messages
928
Loc.
Chandler, Az
Here's mine. 3x3 square tube and 1 1/4 tube.
 

Attachments

  • DSCN2354.jpg
    DSCN2354.jpg
    79.7 KB · Views: 102
  • DSCN2355.jpg
    DSCN2355.jpg
    82.5 KB · Views: 112

BIGED

Guru ????
Joined
Oct 30, 2007
Messages
2,003
heres mine welded to the rocker
 

Attachments

  • 100_1740.jpg
    100_1740.jpg
    115.7 KB · Views: 111
  • 100_1760.jpg
    100_1760.jpg
    97.5 KB · Views: 107

ransil

Bronco Guru
Joined
Sep 6, 2003
Messages
8,138
I used about 5 foot of 2x6 each side, cut 1" below rocker ( inner & outer panel) and weld. I also angled the ends.
 

Scoop

Contributor
Bronco Old Fart
Joined
Feb 1, 2006
Messages
11,121
Loc.
Cuchara, CO
I used about 5 foot of 2x6 each side, cut 1" below rocker ( inner & outer panel) and weld. I also angled the ends.

I did the same as Randy.
 

Attachments

  • DSC03829.jpg
    DSC03829.jpg
    138 KB · Views: 101
  • DSC03830.jpg
    DSC03830.jpg
    130 KB · Views: 92

gravy

Bronco Guru
Joined
Sep 4, 2006
Messages
1,236
Loc.
Parsippany
Rock Sliders

I did the same as Randy.


Here is mine. I cut all off except 1 1/2 inches where I attached 1 1/2x 1 1/2 angle iron. This also supports the fender. Then used 1 5/8 chromoly for the tubing. I also tied the roll cage to the frame throug the sliders
 

Attachments

  • DSC01069.JPG
    DSC01069.JPG
    27.4 KB · Views: 51
  • DSC01062.JPG
    DSC01062.JPG
    37 KB · Views: 61
  • DSC01063.JPG
    DSC01063.JPG
    41.8 KB · Views: 62
  • DSC01061.JPG
    DSC01061.JPG
    32.8 KB · Views: 67

AWS

Sr. Member
Joined
Aug 2, 2004
Messages
596
Loc.
ST LOUIS
Like this. I'll make more.
Steve
 

Attachments

  • bling 007.jpg
    bling 007.jpg
    166 KB · Views: 90
  • bling 008.jpg
    bling 008.jpg
    106.6 KB · Views: 120
Top