• Just a reminder that you won't be able to start new posts or reply to existings posts in the Archive forum.

    This is where all the old posts go so they can still be used for reference and searched.
  • Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

lift (lowering) help

SGM_JakeAlex

Contributor
Sr. Member
Joined
Sep 7, 2009
Messages
690
Loc.
New Albany, MS
Hello, I have never owned a 66-77 bronco but have been looking very hard for the right one for a few weeks now. I have been lucky enough to find 6 or 7 but nothing that I’ve have felt lead to jump on. With that said, the one I’m leaning closest to is a 77, with hard top/doors, PS, disk breaks on front, Auto trans with a 302 powering the vehicle. The body is strait and best I could tell (and per the seller) all rust has been cut out and holes replaced with new metal.

The dilemma…the rig looks to have somewhere close to 5 or 6 inches of lift and is running 35’s. Under the back leaf springs, there are blocks that looks to be about 3 inches. When riding off road, you can feel the cab sway pretty badly. I didn’t like the feel of the “sway” and honestly, I don’t really care for all the lift that it has.

The question…For someone that is not mechanically inclined, is there a way I can tell how much total lift is on the rig? If so, Id then like to subtract the amount from the rear blocks (because I would want to remove them) and then wonder if I would simply be able to purchase a new pair of front coils so I could lower it back down without having to spend $800 on a new complete lift. If so, is there a way I will be able to know what size coils I would need?

Does this request sound crazy? I just want to know so I can try to figure out if I want to spend what he’s asking ($7k) without having to spend nearly another grand to get the “look” I want.
 

Myllo73

Full Member
Joined
May 30, 2009
Messages
154
In the past few weeks there was a post that would answer the question. It told where to measure and how much you should have when compared to stock height. Do a search and you should be able to find that. As far as lowering it, you will better off spending what it takes to do it correctly and make it what you want. By that I mean replacing sagging springs, you may have to shorten drivelines, get shorter shocks, correct the steering, etc. I'm sure there is more to it than my 2 cents.
 

broncosilver

Full Member
Joined
Feb 26, 2006
Messages
198
Loc.
springhill fl.
myllo is correct, if you want the truck to ride right there is more to it than just putting new springs in. you need to ask some questions to the owner. he "should" know how much lift is in it. does it have a body lift? did he buy a complete kit? does it have a drop pitman arm? lowered radius arm brackets? these are the parts you may need to buy stock depending on how low you want to go. there is an up side. if these are fair parts you could trade them for good stock parts. there are way more people on this site looking for these parts and have a bunch of stock stuff laying around. i have two sets of 3.5" coils you could have if they would help. this job is not to hard to do with a good selection of hand tools alittle mechanical know how and alot of common sence. you came to the right site for help. i dont think theres anyone here not willing to help a fellow bronco guy out!!
 
OP
OP
SGM_JakeAlex

SGM_JakeAlex

Contributor
Sr. Member
Joined
Sep 7, 2009
Messages
690
Loc.
New Albany, MS
I understand and that make sense. Thank you both for you opinions. Guess I'm just really trying to talk myself info a purchase. I had planned on buying a bronco before this week. As luck would have it, I've yet to find one that already seems dependable. Also guess trying to cut conners on$ might not be the best option either. Again, thanks.
 

Heus33

Bronco Guru
Joined
Jun 1, 2005
Messages
7,488
$7,000 is a good amount of money to spend on a Bronco. You should be able to find a nice rig for that price. If this one doesn't butter your bread, keep looking. Remember, you can always take a bus or a plane and drive one back too! What a great story that would be.
 

broncotime

Bronco Guru
Joined
Jun 30, 2003
Messages
1,188
Loc.
Grapevine, Texas
I'd be cautious about what other corners were cut once I see lift blocks in the rear. Most of the one's I've seen were used as a cheap way to get 3 inches of lift out of already worn out stock leafs. The axle wrap you will get out of the blocks is scary and if you plan on doing any low range crawling, look out for damage to your drive shaft/rear end.

If you are looking at the $7k range as mentioned in an earlier post, you should b eable to do much better than lift blocks and should be able to find the exact truck that meets your needs. Take your time and be patient or you will end up spending more $$$ than you thought just to replace basic things. Save your money for the upgrades you want ot do, not the ones to fix a PO's cheap lift.

Just my 2 cents (from someone who owns 2 EB's with 3 inch rear lift blocks, and no I didn't install them, they came that way).
 

Skiddy

Bronco Guru
Joined
Oct 8, 2003
Messages
11,587
I'd be cautious about what other corners were cut once I see lift blocks in the rear. Most of the one's I've seen were used as a cheap way to get 3 inches of lift out of already worn out stock leafs. The axle wrap you will get out of the blocks is scary and if you plan on doing any low range crawling, look out for damage to your drive shaft/rear end.

If you are looking at the $7k range as mentioned in an earlier post, you should b eable to do much better than lift blocks and should be able to find the exact truck that meets your needs. Take your time and be patient or you will end up spending more $$$ than you thought just to replace basic things. Save your money for the upgrades you want ot do, not the ones to fix a PO's cheap lift.

Just my 2 cents (from someone who owns 2 EB's with 3 inch rear lift blocks, and no I didn't install them, they came that way).
lol and i thought you was talking about my bronco;D
 
OP
OP
SGM_JakeAlex

SGM_JakeAlex

Contributor
Sr. Member
Joined
Sep 7, 2009
Messages
690
Loc.
New Albany, MS
Thanks guys. Patience is real hard to have now that my mind is stuck on owning one of these things. Several people have told me that 7k would be more than enough to own a good solid ride. Thing is, I haven't found one yet that I could actually drive home and prices range from 3500 to 9k. Wouldn't mind getting one off somewhere where I would have to drive it a good piece home IF it would make the trip without breaking down. Thanks for the input. Guess I'll just keep waiting.
 
Top