• Just a reminder that you won't be able to start new posts or reply to existings posts in the Archive forum.

    This is where all the old posts go so they can still be used for reference and searched.
  • Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Help! Door Hinge Backing Plate

msweb

Bronco Guru
Joined
Aug 29, 2003
Messages
2,377
I took the doors off my Bronco and proceeded to break 5 out of 6 bolts in the door hinge backing plate on the driver side, 3 out of 6 on the passenger side. What now? Leaving the doors off isn't an option.

I can't take my fenders off to access them because everything is covered in Rhino Lining and I'd have to cut it all up. The bolts aren't sticking out enough to get a nut on them to hold the backing plate still while I drill/ez-out the bolts.

Has anyone cut an access hole in the inner kick panel to get to them? I think I can make new ones if I can get them out. They look like they'd be pretty simple to make. Any reason why I couldn't?
 

farnorthdan

Full Member
Joined
Dec 15, 2009
Messages
344
Loc.
Eagle River, Alaska
We had the same thing happen on my 73'. we were removing the lower hinge on the drivers side to replace due to a bad pin. Two of the three bolts in door pillar broke. I ended up using a new hinge so we took the old hinge and cut the side off that mounts to the pillar and used it as a backing plate, it worked great....purfect fit...of course my inner wells are plenty rusted so no problem with access...


Dan
 
OP
OP
msweb

msweb

Bronco Guru
Joined
Aug 29, 2003
Messages
2,377
Not a bad idea. If nothing else, I can use the hinge as a template
 

crab

Bronco Guru
Joined
Feb 23, 2004
Messages
2,268
I've had great success from with helicoils. Go to napa and pick up a 5/16 set. They're cheap and if you don't have the patience, you're not out much. 1st couple will be a @#!&# but a pretty simple fix. I'd try that before hacking out my kick panels.
Good luck CRAB
 

tk1218

Bronco Guru
Joined
Nov 23, 2008
Messages
1,074
Loc.
Flower Mound
You will need to cut through the inner fender bottom to get them out. I pulled mine out and used a coat hanger to get the new 1 in place and then tacked it in so I could put the screws back in.
 

Sac '68 sport

Bronco Guru
Joined
Apr 9, 2004
Messages
1,176
Loc.
Orangevale
I was able to get the broken screws out with a propane tourch and vice grips. Once I got the backing plate hot enough they came right out no problem with just a little pair of needle nosed vice grips. Not really an option if you want to save the paint in the door jam though.
 
OP
OP
msweb

msweb

Bronco Guru
Joined
Aug 29, 2003
Messages
2,377
I was able to get the broken screws out with a propane tourch and vice grips. Once I got the backing plate hot enough they came right out no problem with just a little pair of needle nosed vice grips. Not really an option if you want to save the paint in the door jam though.

Not a good idea when it's covered in Rhino Lining either. VERY flammable :eek:
 

Casey835

Sr. Member
Joined
Mar 8, 2008
Messages
759
Unless Im not catching what you said, theres a much easier fix. When I took my doors off some of the screws broke off as well in the door post. What I did was drill the broken screw out with a small bit, then next size up, and so on stopping before you damage threads. Then when the center is drilled out, use something(screw driver, punch, needle nose, whatever it takes to dig the rest out.
 
OP
OP
msweb

msweb

Bronco Guru
Joined
Aug 29, 2003
Messages
2,377
Here's what I've got - the backing plates are floating around so there's no good way to hold it still while drilling out the bolts :mad:
 

Attachments

  • 100_2009.jpg
    100_2009.jpg
    225.6 KB · Views: 280
  • 100_2010.jpg
    100_2010.jpg
    224.7 KB · Views: 251
  • 100_2011.jpg
    100_2011.jpg
    214.6 KB · Views: 274
OP
OP
msweb

msweb

Bronco Guru
Joined
Aug 29, 2003
Messages
2,377
I've had great success from with helicoils. Go to napa and pick up a 5/16 set. They're cheap and if you don't have the patience, you're not out much. 1st couple will be a @#!&# but a pretty simple fix. I'd try that before hacking out my kick panels.
Good luck CRAB

Unless Im not catching what you said, theres a much easier fix. When I took my doors off some of the screws broke off as well in the door post. What I did was drill the broken screw out with a small bit, then next size up, and so on stopping before you damage threads. Then when the center is drilled out, use something(screw driver, punch, needle nose, whatever it takes to dig the rest out.

Good idea but how can I hold the backing plate still while drilling? I guess I could always tack it in place and hope I can bust the tack afterwards?
 

mcdobson

Sr. Member
Joined
Jul 28, 2008
Messages
401
Loc.
Sacramento
I don't get it either. I just rebuilt my hinges and the backing plates didn't fall off.
Lots of PB blaster and an impact driver got mine out without breaking(knock on wood). I still have the passenger side to do.
 
Last edited:
OP
OP
msweb

msweb

Bronco Guru
Joined
Aug 29, 2003
Messages
2,377
I don't get it either. I just rebuilt my hinges and the backing plates didn't fall off.
Lots of PB blaster and a torque driver got mine out without breaking(knock on wood). I still have the passenger side to do.

On the driver's side, the backing plates are loose inside the pillar.
 
OP
OP
msweb

msweb

Bronco Guru
Joined
Aug 29, 2003
Messages
2,377
You will need to cut through the inner fender bottom to get them out. I pulled mine out and used a coat hanger to get the new 1 in place and then tacked it in so I could put the screws back in.

I didn't think about going through the inner fender. How are the plates normally held in place? Why don't they just fall to the bottom when you take the last bolt out?
 

mcdobson

Sr. Member
Joined
Jul 28, 2008
Messages
401
Loc.
Sacramento
How about drilling a hole in the center of the sheet metal, positioning the plate, then tacking through the drilled hole.
You could then just grind the weld and still have it hold the plate.
 

Sac '68 sport

Bronco Guru
Joined
Apr 9, 2004
Messages
1,176
Loc.
Orangevale
I didn't think about going through the inner fender. How are the plates normally held in place? Why don't they just fall to the bottom when you take the last bolt out?

The door post is all closed up. You have to cut a hole somewhere to get the plates out.
 

GrillMaster

Contributor
Bronco Guru
Joined
Jun 5, 2008
Messages
2,505
I need to replace mine. Is it best to just cover with penetrating fluid a few days before and then heat up the bolts with a propane torch??? Would rather burn the paint than break the bolts.

Guess it would be best to run a tap through the threads and use some antiseize durring reassembly
 

Sac '68 sport

Bronco Guru
Joined
Apr 9, 2004
Messages
1,176
Loc.
Orangevale
I need to replace mine. Is it best to just cover with penetrating fluid a few days before and then heat up the bolts with a propane torch??? Would rather burn the paint than break the bolts.

Guess it would be best to run a tap through the threads and use some antiseize durring reassembly

I soaked mine for days and I don't think a drop got in there. I even cut all around the paint with a knife and I don't think it helped a bit. I didn't actually brake any off, 2 of my screws were stripped out so I drilled the heads off so that I still had some stud left to grab with vice grips.
 

Sac '68 sport

Bronco Guru
Joined
Apr 9, 2004
Messages
1,176
Loc.
Orangevale
Maybe you can wedge a pry bar between the sheet metal and backing plate, or a long wooden dowel between the backing plate and the other door post to hold them in place while you drill.
I'd keep hitting them with PB blaster, or I read a few places that 50/50 Acetone and tranny fluid is even better for loosening rusty bolts. Maybe even try a small Pezo torch on the backing plate through the holes before trying an ez out. Don't know if it will get it hot enough but it's worth a try. Get it all ready for the EZ out then focus the heat on the backing plate around the bolts. I think you have enough space there that the rhino should be ok with the pezo. A propane torch will probably catch it on fire. My fender, door post and hinge paint were burnt pretty bad when I was done, but the screws and studs I had left came out like they were brand new while they were hot. Almost no effort at all to turn them out.
 

Bronco_69

Bronco Guru
Joined
Jun 14, 2001
Messages
2,070
Loc.
Monette Ar
i just went through this.

1.put a bolt back through the one good hole to line the other two busted bolts up where they belong.

2. use whatever size nut and 11/16" wrench fits and center it over the broke bolt.

3. use a mig welder (turned up high) to weld from the center of the brok bolt to the inside of the nut. you want lots of heat!!

4. let it cool and then slowly work it out. a mixture of atf and thinner makes a great penetrating oil.



if that fails then take the one good hole and bolt a loose hinge back on while lining the other two broken studs up. use the hinge as a drill guide. use a normal (not reverse) drill bit for this. you may get lucky and it will come loose.
 

surfer-b

Contributor
Bronco Guru
Joined
Sep 7, 2006
Messages
3,013
Why don't they just fall to the bottom when you take the last bolt out?
If you ever cut out the front side of the post you will see how they are held in without falling, they have a box like piece, a little larger than the backing plate, welded to the post. The backing plate is inside of this so it wont fall but will still float around so the door can be adjusted.
As for what to do I would do as another suggested, get the plate so you can get to all the bolts, tack it in place, then drill out and retap. I always try and loosen these bolts if no success I just drill them out before they break. Most of the time after they have been drilled they can be removed without an ease-out.
 
Top