• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

not getting fuel after installing rear tank

ATXbronco

New Member
Joined
Mar 4, 2011
Messages
14
Loc.
Austin
I have 69 bronco with a 302 and edelbrock carburetor. I just installed the stock rear tank after it was removed about 8 years ago because the auxillary tank I was using had a leak. there is an electric fuel pump mounted under the hood pretty close to the location where the mechanical pump went. this pump was originally hooked up to the auxilly tank and got fuel to the carburetor just fine. i disconnected the auxillary fuel line and just connected the rear 3/8" fuel line in its place but now I'm not getting fuel to the carb. I'm thinking it's not working because the fuel line to the rear tank is longer. should I put another pump closer to the tank or maybe just move the pump I have now somewhere closer to the middle of the line? anyone have experience running the fuel lines for the stock rear tanks? I also haven't put a fuel filter in the line yet, not sure exactly where to place it. I was thinking between the pump and the carb.
 

shamu

Lucky as the day is long.
Joined
Jun 18, 2009
Messages
5,290
Loc.
Sachse,Tx
Make sure that your sending unit is not up side down. Don't laught I did that last week.
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,651
If you're still using the stock fuel tank selector valve too, make sure it's now in the MAIN position.
Wouldn't be the first time for that either.

And yes, if the switch is correct, the old pump might be having a bit more trouble priming the longer tube than it had before. Could be from it just being too old too, so you might have to experiment with a different source closer to the pump, or at least put your finger over the output to help prime the input. Don't know why that works, but it can help under the right circumstances.

Good luck.

Paul
 
OP
OP
A

ATXbronco

New Member
Joined
Mar 4, 2011
Messages
14
Loc.
Austin
thanks for the responses, hopefully it's not the sending unit upside down but it could be. I don't have a fuel switch in there right now, just the hose from the tank to the pump. how can I tell if the sending unit is right side up or not without taking it out of the tank? right now the fuel line connection is below the fuel gauge connection
 

shamu

Lucky as the day is long.
Joined
Jun 18, 2009
Messages
5,290
Loc.
Sachse,Tx
thanks for the responses, hopefully it's not the sending unit upside down but it could be. I don't have a fuel switch in there right now, just the hose from the tank to the pump. how can I tell if the sending unit is right side up or not without taking it out of the tank? right now the fuel line connection is below the fuel gauge connection

the fuel line is below. something else to think about, is the sock in the tank clogged?
have you tried to transfer gas from your fuel tank to a gas can to see if your fuel pump works? or try gas can to gas can to see if your ele pump is working.
Better here than on the trail.
 

bad 68

Sr. Member
Joined
Jul 1, 2010
Messages
930
Loc.
Northest Washington
Take the fuel line off at the tank. If the tank had fuel and there is no problem it will run out. If not try blowing air through the hose fitting at around 5 psi. I know this sounds like a bad idea but I would check the problem starting at the tank and working toward the motor.
 
OP
OP
A

ATXbronco

New Member
Joined
Mar 4, 2011
Messages
14
Loc.
Austin
Ok, the carb is getting fuel to it now. The bronco seemed to be running fine at first. I let it warm up for a little then went to drive a loop around the parking lot at my apartment. I made it halfway around and then the bronco died. Checked the fuel line at the carb again and it was empty but fuel came not long after I pulled the hose off. I went to try putting more fuel in and when I twisted the gas cap it blew out with a bunch of pressure. Should it be under so much pressure? At least I think it blew out, maybe it was sucking in. I put and older gas cap on and I'm gonna see if that makes any difference. these caps are supposed to be vented, right?
 
OP
OP
A

ATXbronco

New Member
Joined
Mar 4, 2011
Messages
14
Loc.
Austin
I just ran the fuel pump with the line off the carb and it was just kind of trickling out. I'm gonna check the connection at the tank and if that's good I'll probably try moving the pump a little closer to the tank.
 
OP
OP
A

ATXbronco

New Member
Joined
Mar 4, 2011
Messages
14
Loc.
Austin
Take the fuel line off at the tank. If the tank had fuel and there is no problem it will run out. If not try blowing air through the hose fitting at around 5 psi. I know this sounds like a bad idea but I would check the problem starting at the tank and working toward the motor.

I pulled the line of at the tank and nothing was coming out, just a very slow drip. Does this mean I have a bad sending unit?
 

shamu

Lucky as the day is long.
Joined
Jun 18, 2009
Messages
5,290
Loc.
Sachse,Tx
I pulled the line of at the tank and nothing was coming out, just a very slow drip. Does this mean I have a bad sending unit?

The sock or filter inside the tank is probably trashed. You will need to pull the sending unit to get to it. Be careful if you have over 4 gallons of gas it will pour out all over if you. Syphon the tank first. It will make things much safer. And you wont smell like gas for a week.
 
Top