• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

SpareParts Build Thread...Linked and tons!

OP
OP
SpareParts

SpareParts

Bronco Guru
Joined
Nov 13, 2004
Messages
5,595
It runs!!!

Still need to get the air intake finished, more like decide what I want to do with it. Plugs were fouled when I started the EFI swap, so I know I need to change those also. I have played with the timing and for throttle response 14* seems about right.

As far as a rest drive...mother nature dumped 6-7" of snow on us today. Maybe tomorrow, I don't feel like a snow, night run as a shake down run.

48acd124-955e-da55.jpg
 
Last edited:

Ratch

Contributor
Sr. Member
Joined
Nov 1, 2007
Messages
695
Glad to hear you got it going. Hopefully the snow will be gone tomorrow for a shake down!
 

NYLES

Bronco Guru
Joined
Aug 13, 2004
Messages
9,846
Most cool!!!!!! ya like the way it runs? well in the shop anyway?

It OK the flip IAD upside down? might help my fitment

Glad ya gotter done!
 

broncoitis

Bronco Guru
Joined
Jul 23, 2010
Messages
4,449
Just caught up with the thread and definitely some nice work! Can't wait to just get mine on the road. Nice lookin Bronco for sure. Keep up the good work. :cool:
 
OP
OP
SpareParts

SpareParts

Bronco Guru
Joined
Nov 13, 2004
Messages
5,595
Thanks guys,

Nyle's, it runs pretty good in the shop. I smoked the tires off a little in the shop, felt good but it's not a good test on how it runs. :cool:
 
OP
OP
SpareParts

SpareParts

Bronco Guru
Joined
Nov 13, 2004
Messages
5,595
I don't think it makes any difference? When it is open it is open, it don't matter if it's upside down or not.

It runs and idles with no problem, no adjusting even.
 

YellowBronc

Bronco God
Joined
Jan 6, 2002
Messages
1,830
I don't think it makes any difference? When it is open it is open, it don't matter if it's upside down or not.

It runs and idles with no problem, no adjusting even.

That's the magic of EFI!!!!! Haven't been on here in a while. This was good news to read. You were pretty much unstoppable before.........now......Lookout!
 
OP
OP
SpareParts

SpareParts

Bronco Guru
Joined
Nov 13, 2004
Messages
5,595
Runs good, I took it for a test drive tonight. I adjusted the kick down and played a little bit. It does have more power than it has had before. I'm not too surprised at that, considering the Motorcraft 2 barrel that I was running on it!

I did run into a problem, I tried to do the KOEO and KOER tests and it came ip computer not connected. I also am not getting a check engine light test when the key is turned on.

I rechecked all the wiring between the computer and the data link and they all checked out fine, less than .2 ohms. The computer is a A9P, the #30 wire is hooked to the "s" terminal on the soleniod. After rereading the #30 bulletin, I do have a little bit of idle surging like he stated as well as no codes. I'm pretty sure I have a bad EEC. They have a new one on order for me and it will be on on Wed.
 
Last edited:

YellowBronc

Bronco God
Joined
Jan 6, 2002
Messages
1,830
Dave, I've been thinking about your no MIL light issue. It sounds like you already have an EEC on the way but maybe another way to check things would be to do it manually (so to speak). I think the Self test out "STO" is the same wire that goes to the MIL.
So my thinking is you could ground the single wire "Self Test In" (STI). Then use a test light or voltage meter between the positive side of the battery to the "Self Test Out". Then turn the key to "On" and the self test should start. Once the fuel pump stops going you should get codes through the light or voltage meter.

This may at least tell you if the EEC is giving the light indication.
 

Attachments

  • selftest04.gif
    selftest04.gif
    4 KB · Views: 55
Top