• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Inspection Height

70bronc

Sr. Member
Joined
Jul 4, 2004
Messages
399
Loc.
st. peters, MO
Ok so got my new (to me) 76 and still working out the kinks. One of those being... i just failed inspection. Im too high. I am not a suspension/lift guru.... what it the quickest/safest way to lower my rig about 3 inches?

2011-09-27_13-35-13_209.jpg


2011-09-27_13-35-25_482.jpg


2011-09-27_13-35-34_958.jpg
 

Rustytruck

Bronco Guru
Joined
Feb 24, 2002
Messages
10,872
Where are they measuring? If frame to ground borrow a set of smaller tires.
 
OP
OP
70bronc

70bronc

Sr. Member
Joined
Jul 4, 2004
Messages
399
Loc.
st. peters, MO
5.5 which i though was pretty close to my 70, so not sure why this one's too high. oh well, maybe my 70 just went unnoticed, or the laws have changed.
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
Hey 70. Lots of stuff done to that rig for sure.
First thing I would do is measure the distance between the front bumpstop (if it's still got stock beehive shaped bumpstops that is) and a frame rail. Anything over 7" (edit: corrected from my previous statement) is the amount of lift you have currently. From there we can better address how far down you have to go.

FYI, that 9" is stock, so they can't make you go below that. How much is allowed in your area?
Did they mention the steering rode ends? They look to be of smaller size than the more desirable ones, and are obviously not stainless steel either. As the extensive rust will show. I'd consider replacing them with new ones, just out of hand, but I suppose it's better to just do a quick test to see if they're loose at all first. If they're still tight, then there's not much reason to change them out.
If they're loose, see if you can find some more robust looking versions. If available to fit into your tie-rod tubes.

Looks like you might have our variable rate coils up front there, but they're already looking a bit compressed. If that's the case, even if they're 5.5" coils, you might not have that amount of lift anymore. Hence the bumpstop measurement.

Good luck. Let us know what you find. Hopefully you won't have to go too far down. But at least the springs are easy to replace if you end up having to go way down, then want to go back up afterwards.
Oh, and did you get any of the old stock parts with your purchase? Things like pitman arms and shorter shocks might come in handy and help you not spend so much to lower your rig.

Paul
 
Last edited:

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
35" tires? Like mentioned, borrow some smaller ones and see what you get. If just bumpers and headlights are the concern, tires might be enough.

Paul
 
OP
OP
70bronc

70bronc

Sr. Member
Joined
Jul 4, 2004
Messages
399
Loc.
st. peters, MO
yea i didn't get the old stuff, and i sure dont want to have to replace it all (ugh). Im not sure about the stoppers, ill have to check.

yea, 35" tires.
 

73azbronco

Contributor
Bronco Guru
Joined
Nov 11, 2007
Messages
8,781
let the air out of the tires, 3 inches right there.

Put in about 1,000lbs of dead weight.

What specific thing are you failing, bumper to ground height, headlight height?
 

daddycreswell

Contributor
Bronco Guru
Joined
Jul 30, 2011
Messages
2,854
Loc.
Lebanon, TN
Boy am I glad we don't have to do this type of thing in Tennessee. Another reason why it's the greatest state in the country
 

Explorer

Bronco Guru
Joined
Mar 2, 2008
Messages
4,390
Loc.
Raphine, Virginia
Stock wheels and tires should do it to just pass inspection, you're on your own after that. Anything else is going to get involved. VA is 20' bumper height if I remember right and some lower their bumpers.
 

73azbronco

Contributor
Bronco Guru
Joined
Nov 11, 2007
Messages
8,781
Then weigh her down, make sure to strap the wieghts down in front, even to the bumper if you need. I can get mine to sag an inch with just me at 230lbs.
 

Old School

Sr. Member
Joined
Jun 22, 2011
Messages
440
Loc.
AZ
Unbolt the bumper.

Bolt it back on with the top of the bumper on the bottom of the frame.

Voila' 4 inches lower.
 

76 bronco J

Bronco Guru
Joined
Oct 20, 2005
Messages
1,480
First thing I would do is measure the distance between the front bumpstop (if it's still got stock beehive shaped bumpstops that is) and a frame rail. Anything over 9" is the amount of lift you have currently.


Paul

>>> general consensus is......7 inches from the bottom of the frame rail to the top of the axle tube is stock height......9 inches from the top of the stock bumpstops to the frame rail is alot of lift......
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
Oops! You're right J. Sorry for the mis-direction there everyone.
Thanks for the correction. I'll go back and correct my post.

Paul
 
Top