• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Black Cloud Boob Job Build Thread

OP
OP
C

coby

Full Member
Joined
Apr 24, 2003
Messages
317
Loc.
Fort Collins, CO
Gonna get her rewired...it's been a long time and I wasn't the best wirin' guy to begin with. What's the current best setup for doing a lot of custom circuits? Kinda like that Access 24/7 fuseblock; is that fairly waterproof and durable? Is Painless still one of the better fuseblocks around? Who's making a good starter harness that plays nice with the SEFI and has extra room for lots of custom stuff?

Ben over at Filthy turned me onto the BlueSea stuff...I'm really diggin' the power distribution switch panel. Check it out: BlueSea WeatherDeck™ Waterproof Circuit Breaker Panels
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
So you gonna keep the Hanson stuff on there still Coby, or are you going to start completely from scratch?

Good luck in the build. Hope it rolls along smoothly. It's going to be fun either way though, I'm sure.

Paul
 

SC74

Contributor
Bronco Guru
Joined
May 24, 2004
Messages
3,472
Subscribed....

Great pics on the link... keep them coming!
 

Scoop

Contributor
Bronco Old Fart
Joined
Feb 1, 2006
Messages
11,122
Loc.
Cuchara, CO
Gonna get her rewired...it's been a long time and I wasn't the best wirin' guy to begin with. What's the current best setup for doing a lot of custom circuits? Kinda like that Access 24/7 fuseblock; is that fairly waterproof and durable? Is Painless still one of the better fuseblocks around? Who's making a good starter harness that plays nice with the SEFI and has extra room for lots of custom stuff?

Will be following this thread too. I think I was getting active on CB about the time you left - so really don't know much about your first build.

You might want to look at the new Painless Bronco harness. They redesigned the harness with LOTS of help from the forum. They did a nice job.
 
OP
OP
C

coby

Full Member
Joined
Apr 24, 2003
Messages
317
Loc.
Fort Collins, CO
So you gonna keep the Hanson stuff on there still Coby, or are you going to start completely from scratch?

Good luck in the build. Hope it rolls along smoothly. It's going to be fun either way though, I'm sure.

Paul

The Hanson bumper, which I lusted after about 15 years ago and have run for a hella long time, is coming off. It's just too wide for 42's and havin' that front axle pushed forward. I'll put it up for sale. Still love that bumper. Aaron's going to fab up a new, narrower version of the Hanson design.
 
OP
OP
C

coby

Full Member
Joined
Apr 24, 2003
Messages
317
Loc.
Fort Collins, CO
Meats!

Tahres showed up today!!

20120124-IMG3670-X2.jpg


They shipped quick....unlike the Creepy Crawlers I tried to get.

20120124-IMG3634-X2.jpg


I dig the tread; the voids are freakin' huge. I'm used to the old Super Swamper TSL's so this is a switch for me. These are 42" by 15" Pitbull Rockers on 17" rims.

20120124-IMG3699-XL.jpg


Here's approximately where the axles outta end up. Gonna have to cut up to the front grill, and back to the rear taillight housing. Gonna have to narrow the front. Don't wanna narrow the rear though....we'll deal with it. I'll sell the tailgate and make a tube one...that'll save weight too, hopefully. We got some talkin' done on how to do the cage. Looks like a fair bit of frame will be cut out as well. Body will be rigidly supported with the tube frame.

20120124-IMG3638-X3.jpg


Winch showed up today too..went for the Warn 9500 XP-S instead of the usual 9500...I like the lower profile and slightly faster pullin'.

Got the plan worked out mostly for doing the paint as well. Going to get new panels for the quarters and the fenders instead of dealing with that rust. I'd like this rig to last another 20 years at least. Oh, and we're going to fab up door inserts out of steel instead of doing fiberglass....outta survive longer and be stronger.
 

bsquared

Contributor
Sr. Member
Joined
Dec 4, 2010
Messages
972
Man - o - Man....talk about some GOOD Bronco dirty-pics! I am going to live vicariously through your pocket-book. Muy Loco! Me likey. Subscribed
 

camomog

Full Member
Joined
Sep 10, 2008
Messages
254
Loc.
Reno, Nv.
I remember when you did the exo cage and had it at the bronco reunion way back when. I also had a exo cage though much simpler with a camo paint job. So if you are cutting and tubing part of the frame and changing body panels, why not throw in a 10" stretch? It would give more room inside and let the tail lights remain bronco in apperance and wouldn't be much extra work. Just a thought, I do like how you are building this.
 
OP
OP
C

coby

Full Member
Joined
Apr 24, 2003
Messages
317
Loc.
Fort Collins, CO
I remember when you did the exo cage and had it at the bronco reunion way back when. I also had a exo cage though much simpler with a camo paint job. So if you are cutting and tubing part of the frame and changing body panels, why not throw in a 10" stretch? It would give more room inside and let the tail lights remain bronco in apperance and wouldn't be much extra work. Just a thought, I do like how you are building this.

It's a thought, but if I did that I'd lose that departure angle. Aaron's trying to talk me into dovetailin' it. Gah. I'd prefer to leave the back straight if possible. But if we have to, we have to. Gotta keep the CG low and gotta flex.
 

roundhouse

Bronco Guru
Joined
Sep 5, 2003
Messages
2,956
Does "Full hydro" mean no real mechanical link 'tween the steering wheel and the tie rod?

If so ,Id be nervous about that on the highway.
 

Madgyver

Bronco Madman
Joined
Jul 30, 2001
Messages
15,030
Ah, I remember the "Black Cloud"

Coby,
you still got 427 in there?
 
Top