• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Dana 60 front swap question

TRABY

Jr. Member
Joined
Oct 7, 2011
Messages
128
Loc.
Little Rock Arkansas
I've purchased a Dana 60 front with a matching Sterling rear from an 04 Superduty, and my question is this: I plan to get a set of the weld on "c"'s from James Duff, how difficult is it to get the bushings in the correct orientation to ensure proper caster angles? Can the drivers side spring perch be cut off to offer more room? I plant to run about a 40" tire and I'm not looking for major articulation, just a solid mud truck with decent street manners. My Bronco already has radius drop brackets from the previous owner and I'm not too worried with them grabbing rocks, because it will never see any rock crawling. Thanks for y'alls help
 

SpareParts

Bronco Guru
Joined
Nov 13, 2004
Messages
5,595
You are in Little Rock, AR....and won't go rock crawling? In two weeks there is the second biggest Bronco event in the world going on just miles from you! You NEED to go to OCBR, it will give you all kinds of ideas. It's in Hot Springs in case you haven't heard about it. Two weeks away!!

Sorry, I'm kinda excited about going again for my 7th year in a row. Back to your question, the D60 from a 04' I believe is pretty close to the 88' that I have in mine. You will get real freindly with a grinder if you want to remove the pearch from the axle on the diff. side. That is what I think you have to do to use the newer axles. Call Suzy "Duff" and ask here in the morning, she'll have the correct answer and sells the weld on wedges. I used the Cage stuff and I'm having problems with not having the C-bushings. After OCBR I'm tearing mine apart and going to do 3 link. My pics are in my build thread below, they may give you some ideas.
 

KyleQ

Bronco Guru
Joined
Apr 24, 2008
Messages
5,480
You can hack off the leaf spring perch off the center section, it will be fine and has been done many times. I don't think you need to though - I'm running cage arms on my 90' D60 and didn't need to cut anything. All of the axles from 80' on up have the same spacing, if we didn't have problems, you won't.

 

brewchief

Sr. Member
Joined
Feb 11, 2007
Messages
877
The super duty axles I've seen only have about an inch of tube showing, I think fitting C's will be tough.
 

allenfahey

Bronco Guru
Joined
Mar 18, 2004
Messages
2,672
Something else to watch out for when doing a D60 swap is the headers. I have a 79 D60 and the long tube headers dump right into the pumkin. Had to get Wild Horses shorties.

SpareParts... Curious since I have Cage arms. What kind of problems are you having with the arms and no bushings?
 

SpareParts

Bronco Guru
Joined
Nov 13, 2004
Messages
5,595
SpareParts... Curious since I have Cage arms. What kind of problems are you having with the arms and no bushings?

I'm eating the bushings between the arms and the weld on mounts. The first set lasted and looked brand new when I did my ton swap. That's also when I switched to the weld on mounts. They were probably out after a short time but never paid close attention. I changed them right before OCBR last year and after it and one other trip I noticed they had movement in them again. Suzy and I talked about it and all we could figure out was because the C bushing wasn't taking up any of the slack, the small bushings have to take all the flex. The other thing to contribute is that the 40" tire should have a vertical separation of about 10" or 1/4 of the tire size. The Cage/Duff arms only have 4 1/2", this puts a lot more stress than most people running 35's. 3 link is in my future because of some of this, along with wanting to progress.
 

KyleQ

Bronco Guru
Joined
Apr 24, 2008
Messages
5,480
I'm eating the bushings between the arms and the weld on mounts. The first set lasted and looked brand new when I did my ton swap. That's also when I switched to the weld on mounts. They were probably out after a short time but never paid close attention. I changed them right before OCBR last year and after it and one other trip I noticed they had movement in them again. Suzy and I talked about it and all we could figure out was because the C bushing wasn't taking up any of the slack, the small bushings have to take all the flex. The other thing to contribute is that the 40" tire should have a vertical separation of about 10" or 1/4 of the tire size. The Cage/Duff arms only have 4 1/2", this puts a lot more stress than most people running 35's. 3 link is in my future because of some of this, along with wanting to progress.

Yeah - I've roared through a set of these after only a few trail rides, front digs are not helping either %) They are not all that hard to replace, I'm chalking it up as regular maintenance, but I get a few years out of mine...
 

SpareParts

Bronco Guru
Joined
Nov 13, 2004
Messages
5,595
My last set I only got a few Days of wheeling! Not a bad design, just not big enough for the ton's and 40's.
 

KyleQ

Bronco Guru
Joined
Apr 24, 2008
Messages
5,480
Yikes, maybe I'm on the edge with 37's... I'm mostly on dirt and mud though, I stay away from the rocks so far. Where do you wheel?
 

sstclair

Sr. Member
Joined
Dec 10, 2007
Messages
399
I'm eating the bushings between the arms and the weld on mounts. The first set lasted and looked brand new when I did my ton swap. That's also when I switched to the weld on mounts. They were probably out after a short time but never paid close attention. I changed them right before OCBR last year and after it and one other trip I noticed they had movement in them again. Suzy and I talked about it and all we could figure out was because the C bushing wasn't taking up any of the slack, the small bushings have to take all the flex. The other thing to contribute is that the 40" tire should have a vertical separation of about 10" or 1/4 of the tire size. The Cage/Duff arms only have 4 1/2", this puts a lot more stress than most people running 35's. 3 link is in my future because of some of this, along with wanting to progress.

Dave, a couple questions.. 10" vertical seperation? between the arm and bumpstop? Also, I'm buying what you say about the small bushings because I questioned it before I went to weld ons. I'll have to see what mine look like now they have some serious trail time on them. The progression though, what do you hope to gain over long arms?
-Steve
 
OP
OP
T

TRABY

Jr. Member
Joined
Oct 7, 2011
Messages
128
Loc.
Little Rock Arkansas
Axle

The axle I have came out of what the PO was told was an '04 Superduty, I can't find a BOM on the tubes and the only thing I can find is "248" cast into the pumpkin and the yoke nut is bigger than 1 1/4" so I'm told this means Dana 60?? I picked them up this morning and there is MAYBE an inch to work with on the short side so how can the stock configuration go in here without removing some or all of that spring perch? Again, I don't want major articulation, just good street manners and a mud beast....
 

sstclair

Sr. Member
Joined
Dec 10, 2007
Messages
399
The axle I have came out of what the PO was told was an '04 Superduty, I can't find a BOM on the tubes and the only thing I can find is "248" cast into the pumpkin and the yoke nut is bigger than 1 1/4" so I'm told this means Dana 60?? I picked them up this morning and there is MAYBE an inch to work with on the short side so how can the stock configuration go in here without removing some or all of that spring perch? Again, I don't want major articulation, just good street manners and a mud beast....

Sorry for the hijack.. I haven't been able to find measurements but from some of the pics I found it looks like they went crazy with with casting to the point it's like you described, not nearly as much room in as in the earlier 60s, mine is an 89 with 3.25 inches between the knuckle and the casting. With the earlier ones, I've seen people do a combination of some of the casting and some of the wedge, then the c kind of overlaps onto the casting a little. One other concern I would have is that they went to the metric wheel pattern on the SD, are you thinking of going to 5 on 5.5 or do you have something else in mind for matching rear axle?
 
Last edited:
OP
OP
T

TRABY

Jr. Member
Joined
Oct 7, 2011
Messages
128
Loc.
Little Rock Arkansas
Axle

I got the matching Sterling 10.5 so no real concerns on lug pattern yet. Is the drivers side tube plug welded and pressed in? I think it is if I'm not mistaken, I should be able to cut all of the spring perch and some of the webbing/supports and just smooth it off and re-weld the entire axle tube all the way around and gussett it if needed??? Or am I gonna mess it up? There is about 7/8" axle tube between the perck and the knuckle
 

brewchief

Sr. Member
Joined
Feb 11, 2007
Messages
877
Your axle should a 60, only because they gave up on the dana 50 before the SD.
They did not give up on the 50 before the superduty, lots of superduty came with 50 including mine.

The dana expert site tells me you have a 2002-2003 dana 60 from the numbers posted on pirate.
 

sstclair

Sr. Member
Joined
Dec 10, 2007
Messages
399
They did not give up on the 50 before the superduty, lots of superduty came with 50 including mine.

The dana expert site tells me you have a 2002-2003 dana 60 from the numbers posted on pirate.

Thanks for setting me straight. I have to admit I was quoting something I stumbled on without verifying it.
-Steve
 

KyleQ

Bronco Guru
Joined
Apr 24, 2008
Messages
5,480
I'll duplicate my Pirate4x4 post for those who like info-
-info taken from a P4x4 build thread- BJ D60 Build

If you search you can find plenty of threads where people are successfully cutting that leaf casting out of the way...

DSCN0487.jpg
DSCN0488.jpg


and...

ATT00013.jpg
ATT00016.jpg
 

SpareParts

Bronco Guru
Joined
Nov 13, 2004
Messages
5,595
Dave, a couple questions.. 10" vertical separation? between the arm and bump stop? Also, I'm buying what you say about the small bushings because I questioned it before I went to weld ons. I'll have to see what mine look like now they have some serious trail time on them. The progression though, what do you hope to gain over long arms?
-Steve

The vertical separation that I'm talking about is the distance you have between the attaching points of the arm/arms on the front axle. The Cage and Duff arms only have 4 1/2" between the attaching bolts that hold them to the axle on either the cast C wedge design or the weld on design. All the stress of keeping the axle from rolling is transmitted through this 4 1/2". If you make the mounting distance further apart and you get more control and less axle wrap. Think of it as a leaver, the longer you make it the easier it is to turn whatever is attached. The long arms are awesome for almost every bronco out there. When you get to a taller tire, they take more separation to keep the axle under control. I think most with 37" have no issues, with the 40's along with the power and weight of mine, I'm eating the bushings, this is what I mean by progression!

Sorry for the Hi-jack!
 
Top