• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

LOWERING my Bronco

OP
OP
greatguy57078

greatguy57078

Contributor
Bronco Guru
Joined
Jul 15, 2006
Messages
3,430
nice tank...can you run intank pumps with it? i see more holes in it...or are those for different filler neck options?

Yes. I bought the tank from Tanks,Inc over in Iowa. You can use any one of the three filler locations. The two holes in the top (with the six mounting holes) have a baffle under them for the "in tank" fuel pump. Of course the rear most hole (with 5 mounting holes) is for the sending unit. I bought everything I needed from Tanks.
 

Attachments

  • 100_8621.jpg
    100_8621.jpg
    74.8 KB · Views: 63
OP
OP
greatguy57078

greatguy57078

Contributor
Bronco Guru
Joined
Jul 15, 2006
Messages
3,430
I was going to run the tank behind the bulkhead, but after trying to figure out where I would locate the wiring panel and ECU I decided to place it back underneath. I am either going to run the wiring/ecu behind the seat (stand the bulkhead up straight), or right behind the bulkhead out of the way. I bought a nice waterproof/dustproof Hoffman enclosure to stuff all the sensitive components into.
 

Attachments

  • 100_8631.jpg
    100_8631.jpg
    39.4 KB · Views: 52
  • 100_8634.jpg
    100_8634.jpg
    35.7 KB · Views: 54
Last edited:
OP
OP
greatguy57078

greatguy57078

Contributor
Bronco Guru
Joined
Jul 15, 2006
Messages
3,430
Hard lines are run. Tank is pretty much mounted just have to finish cutting the straps to fit and get some rubber mounting strips.

After seeing what my buddy had to deal with using the Lincoln 4.6 DOHC engine in his '65 Mustang fastback, I decided to just go with the hydroboost. Considering the cost of the vaccuum booster kit, and the advantage of the hydroboost, it was a no-brainer for me. The fact that I wouldn't know if the vacuum booster would even fit was the deciding factor here.

I found the "inline bracket" on eBay (ant0290) that should resolve any clearance issues that I may have had using the conventional '76-'77 angle vaccum booster/bracket. It repositions the whole hydroboost assembly over the driver's side wheel well.
 

Attachments

  • lines again.jpg
    lines again.jpg
    71.6 KB · Views: 78
  • INLINE BRACKET.jpg
    INLINE BRACKET.jpg
    54.3 KB · Views: 77
OP
OP
greatguy57078

greatguy57078

Contributor
Bronco Guru
Joined
Jul 15, 2006
Messages
3,430
Mine won't have that much rake...but I like the concept! Hopefully I get the headers welded up tomorrow and the engine/trans back in the chassis. Moving closer to getting the body on the frame pretty soon...I hope!
 
Last edited:
OP
OP
greatguy57078

greatguy57078

Contributor
Bronco Guru
Joined
Jul 15, 2006
Messages
3,430
All the hydroboost items are ordered, and all the hard brake lines should be installed by this weekend. Also all the radiator parts are in hand except the fan assembly which should be here by the end of the week. Getting closer to purchasing the wiring harness and having the ECU reflashed. I am getting excited about (possibly) getting this driiving by this summer! :p
 
OP
OP
greatguy57078

greatguy57078

Contributor
Bronco Guru
Joined
Jul 15, 2006
Messages
3,430
Ok. I stripped off the original harness. The headers are welded, painted and back on the engine. So the 4.6 DOHC "fat piggy" is ready to re-install back into the chassis tomorrow.

Onward ho! :p
 

Attachments

  • 222.jpg
    222.jpg
    112 KB · Views: 108
OP
OP
greatguy57078

greatguy57078

Contributor
Bronco Guru
Joined
Jul 15, 2006
Messages
3,430
Well it was another knuckle buster but I got that fat bitch wedged back in the chassis. I have to take the lower water inlet/oil filter bracket and grind some clearance into the bottom to clear the power steering rack.

Then I can mount the Ford Motorsports oil filter adapter on that I found that will allow me to rotate the filter 90 degrees. I need that adapter so I can actually get the filter on and off as it sets too close to the inside frame rail. I will post pics of that tomorrow.
 

Attachments

  • big bitch.jpg
    big bitch.jpg
    102.7 KB · Views: 108

behemoth

Bronco Guru
Joined
Jul 2, 2003
Messages
1,736
Looks really good, is it possible to make or modify an existing oil filter adapter to run a remote oil filter? That is what I did with the 5.0 in mine, makes for easier access and provides more room for the steering, headers and other things in there.
 
OP
OP
greatguy57078

greatguy57078

Contributor
Bronco Guru
Joined
Jul 15, 2006
Messages
3,430
I will post pics tomorrow of the adapter I ended up using. I had a Moroso product, but the Ford Racing adapter is exactly what I needed.
 
OP
OP
greatguy57078

greatguy57078

Contributor
Bronco Guru
Joined
Jul 15, 2006
Messages
3,430
That's the part. The Moroso part was just relocated the filter so you still had to buy another piece to make it work. I may have posted pics of that setup in a previous thread.

Hopefully the Ford Motorsport adapter doesn't get in the way of something else, but it looks like it will work...so far.
 

01Dudley

Sr. Member
Joined
Jul 16, 2012
Messages
974
Loc.
Knoxville
Holy Cow I can't wait to see the headers! Also are you going to notch the frame for the rack and pinion? Looks like with the control arm travels up the tie rod is going to hit the frame?



Well it was another knuckle buster but I got that fat bitch wedged back in the chassis. I have to take the lower water inlet/oil filter bracket and grind some clearance into the bottom to clear the power steering rack.

Then I can mount the Ford Motorsports oil filter adapter on that I found that will allow me to rotate the filter 90 degrees. I need that adapter so I can actually get the filter on and off as it sets too close to the inside frame rail. I will post pics of that tomorrow.
 
OP
OP
greatguy57078

greatguy57078

Contributor
Bronco Guru
Joined
Jul 15, 2006
Messages
3,430
Looks really good, is it possible to make or modify an existing oil filter adapter to run a remote oil filter? That is what I did with the 5.0 in mine, makes for easier access and provides more room for the steering, headers and other things in there.

I may end up doing just that. I bolted the water inlet/oil filter piece on and discovered that I needed to grind a corner off the bottom to clear the steering rack. It should be fine as that is just a threaded hole with a plug in it.

Then while fitting the Ford Motorsport adapter onto the engine, I realized that the original angle of the oil filter surface is not 90 degrees out from the engine, so with the 90 degree adapter it still hits the inside of the frame rail. I can/may mill the mounting surface of the bracket to bring the original oil filter location to an actual 90 degrees and then recut the bolt holes so they stay on the same plane as the mounting surface.

All that said and done, it sure looks like the simple remote kit would be easier, and the results much more predictable.
 

Attachments

  • trim.jpg
    trim.jpg
    92.4 KB · Views: 93
Last edited:
OP
OP
greatguy57078

greatguy57078

Contributor
Bronco Guru
Joined
Jul 15, 2006
Messages
3,430
I trimmed a little more off the end of the OEM bracket today, and tapped the hole a little deeper for the plug. Of course I was very careful not to let any of the shavings fall into the hole. After cutting the end down and cleaning up the mounting surface a little with a file, I found that I had a little more room than I originally had.

I then searched and found a shorter filter that would work for this engine. I went and picked up a Wix 57060. What do you know...it's a very tight fit....but it fits! On and off no problem! No adapter needed! I am pretty happy about that! ;D
 

Attachments

  • trim more.jpg
    trim more.jpg
    92.9 KB · Views: 73
  • rack clears.jpg
    rack clears.jpg
    107.9 KB · Views: 91
  • wix 57060.jpg
    wix 57060.jpg
    109.7 KB · Views: 93

behemoth

Bronco Guru
Joined
Jul 2, 2003
Messages
1,736
That's a tight fit, looks good. I spent what I had getting it one color or close... I'll run it like this.
evupyzys.jpg
9ebezezu.jpg
2adaqydy.jpg
sequoia brown I really like it but I miss the aged patina look it had. That and the colors were closer. Oh well I still grin when driving it.
 
Top