• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Stainless screws for locking hut ring?

jckkys

Contributor
Bronco Guru
Joined
Mar 15, 2012
Messages
5,221
The screw heads that secure the chrome plated rings on the locking hubs are rusty eye sores. There's no protection from the elements, so I'm thinking of trying stainless ones. The problem I'm told, is metal incompatibility. The nut and bolt supplier says stainless screws may seize in non stainless steel. Is there a reason to worry? Would thread seal or anti seize work?
 

Revelation

Bronco Guru
Joined
Oct 9, 2004
Messages
4,825
With the grease being in there I would not worry about it. Stainless is cool!
 

knack

Contributor
Sr. Member
Joined
Feb 2, 2007
Messages
877
Not sure what kind of use the truck sees, but if the screws are going to be stressed a lot, stainless might not be the way to go. Ask your fastener supplier, but I think a grade 5 or 8 alloy steel screw will be less likely to fatigue and break.
 

ntsqd

heratic car camper
Joined
Jan 30, 2005
Messages
5,970
Loc.
Upper SoKA
I think your vendor has it bass-ackwards. Stainless fasteners are predominately made form 18-8 alloy (roughly 302 -304 SST). Being 300 series they will gall the most on like-alloy female threads. Screwing them into carbon steel should not be a problem. Screwing them into aluminum or an aluminum containing alloy may cause trouble from Galvanic Corrosion. Any other alloy will hav ethis trouble, but aluminum is the most active and therefore has the most potential for trouble. Really depends on how much water will be available and can get in between those threads.

If they were load-bearing (like they are on a CJ-5 or Scout's hub) then they're a non-starter as they are about a Grade 2 in strength, at best. They wouldn't be anywhere close to strong enough. However, in a splined-drive type of locking hub all they do is hold the assembly together. They're not supposed to transmit ANY of the driving force. In that use they should be fine.

FWIW my local Ace Hardware stocks chrome plated bolts too. I've never wanted any so no idea what's actually there, but those would also solve your problem.
 
OP
OP
J

jckkys

Contributor
Bronco Guru
Joined
Mar 15, 2012
Messages
5,221
I did have a problem with bolts going through aluminum and cast iron with water present. But that was the long bolts through the water pump, timing chain cover, and water jacket. The cure there was thread sealer. I've owned or own several pistols and revolvers that were made of a combination of stainless and carbon steels. Some are all stainless or all carbon steel. The only problem was an all stainless 1911 45 that had minor galling on the slide and frame bearing surfaces. The 6 screws in the locking hubs only hold the ring on against maybe 15 lbs. pressure from the coil spring. There is no water in there. Ford recommended cleaning the hub and wheel bearings out after fording streams. I learned the hard way to follow this advice. I think I'll put anti seize on every other screw and check them after a few months. I'll happily share the results. I can say the stainless screws look a lot better.
 

bmc69

Contributor
Bronco Guru
Joined
Jun 11, 2004
Messages
12,015
. I think I'll put anti seize on every other screw and check them after a few months. I'll happily share the results. I can say the stainless screws look a lot better.

As a previous poster noted, the compatibility problem is between stainless and adjacent aluminum, not anything steel.

Being in the marine equipment business, we deal (successfully) with that issue every day. There are several brands and types of thread lube that deal very effectively with the issue; all contain some zinc and most include teflon as well. TefGel is probably the most "famous" and the marine industry swears by it. Mercury Marine sells their produce in tubes as "Special Grease 101" or something like that...

I use a zinc-loaded anti-seize on all the bolts in a 5.0, for example, that go through or in to the aluminum intake and the timing cover.

The WORST thing you can do..and we see it all the time, unfortunately...is use the Permatex brand anti-seize sold in every autoparts store that has copper in it.
 
OP
OP
J

jckkys

Contributor
Bronco Guru
Joined
Mar 15, 2012
Messages
5,221
Good to know. My anti seize is the Permatex that works well in most situations. I'll us thread seal for this job. The thread sealer should supplied with new water pumps.
 
Top