• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

EFI Conversion Questions - Preparing to consider the job.

Pruneda

New Member
Joined
Nov 12, 2009
Messages
37
Father just bought a '76 w/ a 302. I have yet to see it, but it sounds like a solid beauty. I have owned 3 5.0L mustangs, so familiar with the engine displacement.

We are considering an EFI Swap, and am wondering if its suggested to convert the entire engine (swap,) from a donor vehicle or just swap out whats needed to do the EFI conversion.

Without digging too deep into it, search results neted me little (nothing) in terms of conversion kits/write-ups and ideas. I am aware the summit made a conversion kit for carb'd mustangs to EFI, but saw nothing for the bronco's.

Any info you all can offer is greatly apprecaited! Thank you!
 

bmc69

Contributor
Bronco Guru
Joined
Jun 11, 2004
Messages
12,015
The Mustang 5.0 EFI is easily the most common EFI conversion done on EBs. Some simply swap out the top end on an earlier block..others the entire Mustang engine. I've done both over the years and the effort is the same either way. There are TONS of threads on here about that upgrade and some good write-ups by those that have done them.
 

rguest3

Bronco Guru
Joined
Dec 13, 2012
Messages
3,780
Easiest May be to built a 5.0 with all the EFI. Keep what you have in the Bronco, when the EFI is complete do the swap all at once. Very little down time as well.
 

76Broncofromhell

Bronco Totalitarian
Joined
Jul 30, 2001
Messages
4,250
Loc.
Grass Valley, CA
Father just bought a '76 w/ a 302. I have yet to see it, but it sounds like a solid beauty. I have owned 3 5.0L mustangs, so familiar with the engine displacement.

We are considering an EFI Swap, and am wondering if its suggested to convert the entire engine (swap,) from a donor vehicle or just swap out whats needed to do the EFI conversion.

Without digging too deep into it, search results neted me little (nothing) in terms of conversion kits/write-ups and ideas. I am aware the summit made a conversion kit for carb'd mustangs to EFI, but saw nothing for the bronco's.

Any info you all can offer is greatly apprecaited! Thank you!


Make sure you are running a 5.0 or 351W camshaft so the firing order is correct, otherwise you'll never get it running right.

I've converted a 351W on my Flat Fender using 5.0 stuff, and it was fairly painless. It's definitely a bargain when you consider what a QJet or Truck avenger, 4 barrel manifold and all the parts and labor cost.

Here's a thread I did a few years back:

http://www.pirate4x4.com/forum/jeep-hardcore-tech/704649-gpw-kicked-carb-curb.html
 

Izzy

Bronco Guru
Joined
Sep 5, 2009
Messages
2,430
Loc.
Texas
I think the answer to your question is going to be based on the condition of the existing engine. If you have a good running engine and no need to replace it, then you can swap in EFI on top of it not problem. But if the engine is worn, then you might as well start with a mustang or an explorer engine and have it rebuilt and then swap that in.

Here are a couple of references I suggest you read up on.

http://www.classicbroncos.com/forums/showthread.php?t=119070

There is an old website that is no longer up called oldfuelinjection that had an incredible amount of info. Unfortunately it is gone but it is still available in archive sites. Try this link.
http://web.archive.org/web/20131229172849/http://oldfuelinjection.com/?p=62

If it does not work, PM me your email address and I will send you the PDFs from the site that I saved before the site was gone.

Good luck and feel free to ask questions. Lots of guys here have done this a few times now.
 

Scoop

Contributor
Bronco Old Fart
Joined
Feb 1, 2006
Messages
11,122
Loc.
Cuchara, CO
Another consideration is whether you want to keep the v-belt or go serpentine. Serpentine is a definite advantage if you'll be upgrading to a a 3G alternator. I kept the v-belt and stuck with the stock alternator and it's worked fine. If you want to go serpentine then consider the entire 5.0 swap which makes it easier.
 
OP
OP
P

Pruneda

New Member
Joined
Nov 12, 2009
Messages
37
Another consideration is whether you want to keep the v-belt or go serpentine. Serpentine is a definite advantage if you'll be upgrading to a a 3G alternator. I kept the v-belt and stuck with the stock alternator and it's worked fine. If you want to go serpentine then consider the entire 5.0 swap which makes it easier.

First off, thank all of you for the great responses!

As for the Alternator..that is a good point. I owned 3 '89 5.0's...all of which got the 130amp alternator upgrade on. Def. gonna write it down.

It will probably be a full swap. I would be smarter to go through a block first IMHO.
 
Top