• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

76-77 dana 44 measurement

moses_m

Full Member
Joined
May 5, 2013
Messages
262
I need a ballpark measurement from center to center on knuckles for a 76-77 dana 44 front axle. Grabbed a 76 dana 44 from a fellow member and installing heim style steering from toms. Had dana 30 before so I cant use that measurement. Thanks.
 

garberz

Bronco Influencer
Joined
Jun 24, 2007
Messages
6,864
Loc.
Conejo Valley, Ca.
Mine is 50 1/2" center to center. My drag link is 41 1/2". The drag link runs from the top of the knuckle to the pittman arm. Stock PS box and arm, 3 1/2" coils. Heim steering, tie rod under, from Duff's.

Mark
 

Attachments

  • 10325177_10201914605456800_2461159867760718859_n.jpg
    10325177_10201914605456800_2461159867760718859_n.jpg
    110.7 KB · Views: 66
OP
OP
moses_m

moses_m

Full Member
Joined
May 5, 2013
Messages
262
thanks exactly what I needed. So you went under? Do you have castle nut on top? What size rims and backspacing are you running? My current rims are 15X10 with 4 inch backspacing. Will that work or do I need a spacer?
 

garberz

Bronco Influencer
Joined
Jun 24, 2007
Messages
6,864
Loc.
Conejo Valley, Ca.
The nuts are on top. Nylon locking nuts. Drilled through the nut and bolt to install 1/8" cotter pins. I'm running 8" rims, with 3 3/4" BS. I was running a 1/4' spacer when it was tie rod over, but now it's not needed. It's very close, so I'd say you'll probably need spacers with the 4" BS.

Mark
 
OP
OP
moses_m

moses_m

Full Member
Joined
May 5, 2013
Messages
262
Yea thats what Im thinking. Have never run spacers. Dont like the thought of adding more parts. Might go to 17" wheel and maybe so it clears everything.
 
OP
OP
moses_m

moses_m

Full Member
Joined
May 5, 2013
Messages
262
whats the different in the trac bar mount? I know the 76 77 track bar is longer than previous years. My bronco is a 69, will my trac bar work? What do I have to do it to make it work with 76 track bar.
 
OP
OP
moses_m

moses_m

Full Member
Joined
May 5, 2013
Messages
262
The kit I got from toms had a couple extra bolts and nuts.
Do all rods just take one jam nut like in pic?
 

Attachments

  • IMG_20141206_135148_503.jpg
    IMG_20141206_135148_503.jpg
    66 KB · Views: 58

Justafordguy

Bronco Guru
Joined
Sep 26, 2009
Messages
6,255
Mine is also 50 1/2" center to center. I just measured it yesterday, getting ready to install 1 ton steering from Extreme Custom Fab.;)
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,651
Steering linkage should always use some sort of retention, such as a jam nut, Nyloc, Loctite, cotter pin, etc.

Your bolt is looking a little out of threads in the pic. Is that just because the nut is still loose? If you're out of threads, you may have to modify the order of the parts installed, or simply leave out that last washer perhaps?

Generally speaking, unless clearance is an issue, you won't need high-angle offset spacers on the tie-rod ends (lower link in your pic) because the rod ends simply rotate and do not change angles in other planes.
The draglink does change angles in multiple planes however, so definitely needs the spacers like you have them.
Maybe someone else can verify, but I would say you could leave the top washer out since the nut is bearing down on the flange of a spacer.
Leaving a washer on the lower end is a good idea I would say, because it would be a little extra safety device in case of a catastrophic failure of the tie rod end.

Like I said, get other's opinions that have used spherical rod ends more often, to make sure. If it's just not tight yet, and has plenty of threads available still, ignore everything I just said...;D

Paul
 
OP
OP
moses_m

moses_m

Full Member
Joined
May 5, 2013
Messages
262
Sorry should of stated that it is still loose. Want to get everything mocked up before I tighten down. 45lbs is what directions recommended
 
OP
OP
moses_m

moses_m

Full Member
Joined
May 5, 2013
Messages
262
Will also drill 1/8 hole through nut and bolt and install carter pin when snugged up.
 

garberz

Bronco Influencer
Joined
Jun 24, 2007
Messages
6,864
Loc.
Conejo Valley, Ca.
Sorry should of stated that it is still loose. Want to get everything mocked up before I tighten down. 45lbs is what directions recommended

45 ft.lbs? That's not right. You're gonna want way more toque than that. The standard torque spec. on those 3/4" bolts is 380 ft.lbs. I'd try to get at least 175 ft. lbs. on those. If it's gets a little loose, it will wallow out your steering knuckles. You can't hurt those heims. I don't think you'd be able to get them too tight. Call Tom's and ask them what the deal is with the 45 ft.lbs.

Mark
 

shifter

Full Member
Joined
May 2, 2004
Messages
181
Loc.
Agua Dulce, CA
Wow the proof reader was on vacation that week. If you have not checked already what grade bolts and nuts are in that kit? That will determine how much torque you can put on them. My two cents is nylocs have no place in a steering linkage anyway. Slotted or castle nuts with cotter pins is much more secure. I like the grade9 F911 bolts, overkill is just right!
 
OP
OP
moses_m

moses_m

Full Member
Joined
May 5, 2013
Messages
262
Will eventually go to stainless on hardware. Bolts are grade 6 5/8" So im thinking 125lbs on nylon nuts and will call Toms on jam nuts for heim joints.
Does the orientation on my radius arm bushings look correct? They are the 4 degree bushing. Hopefully installing diff in tomorrow if brake lines and spacers show up tomorrow.
 

Attachments

  • IMG_20141209_161722_213.jpg
    IMG_20141209_161722_213.jpg
    98.8 KB · Views: 42

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,651
Should be rotated 180 from what I see. If you imagine the angle of the arms being down in the front (from the lift) and the frame brackets being more straight ahead (because they're oriented stock height) then I think your bushings should be the other way.

You want them more level when the arms are down in the front.

Paul
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,651
You'd know anyway, once you start to install them into the brackets. You'll see the natural orientation they'd want to be in.

Thought of just editing my last post, but decided to bump myself up to 19,000 posts with this one! Post-whore that I am obviously...;)

Paul
 
OP
OP
moses_m

moses_m

Full Member
Joined
May 5, 2013
Messages
262
How about now? 19K and counting
 

Attachments

  • IMG_20141210_145314_098.jpg
    IMG_20141210_145314_098.jpg
    83.6 KB · Views: 28

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,651
Hah! Yep, been busy this morning. Looks good from here. The proof is always in the pudding, as they used to say. But looks like it should be the ticket.

Paul
 
Top