• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Gauges and dash

mini73

Sr. Member
Joined
Aug 12, 2013
Messages
969
I'm wanting to add more gauges soon. Thinking of a 5" auto meter speedometer and 5"auto meter tach and auto meter fuel, oil, volt meter, water temp and trans temp gauges. I have the factory gauge in there now. If I get the 5" auto meter speedometer do yall think it will fit where the factory on is? I'm thinking the factory gauge is bigger but not sure. Want to make new holes in the original dash to the right of the steering wheel for the others to go in. I know I could go with a blank dash and place the things where I want but the blank dashs are kind of pricey and I really don't know how to get the old dash out to do it. Is hard to get the dash out and do this? Anyone recommend me cutting the holes while the old dash is in the truck still?
 
OP
OP
mini73

mini73

Sr. Member
Joined
Aug 12, 2013
Messages
969
I'm wanting to add more gauges soon. Thinking of a 5" auto meter speedometer and 5"auto meter tach and auto meter fuel, oil, volt meter, water temp and trans temp gauges. I have the factory gauge in there now. If I get the 5" auto meter speedometer do yall think it will fit where the factory on is? I'm thinking the factory gauge is bigger but not sure. Want to make new holes in the original dash to the right of the steering wheel for the others to go in. I know I could go with a blank dash and place the things where I want but the blank dashs are kind of pricey and I really don't know how to get the old dash out to do it. Is hard to get the dash out and do this? Anyone recommend me cutting the holes while the old dash is in the truck still?


I'm wanting to do something like what is in the pic but with a 5" speedometer and 5" tach. How would I go about making holes in the dash?
ImageUploadedByTapatalk1425331333.992280.jpg
 

jw0747

Bronco Guru
Joined
Nov 22, 2006
Messages
2,434
Loc.
San Antonio, TX
Hole saws...

http://www.homedepot.com/b/Tools-Ha...-Bits-Hole-Saws-Arbors-Hole-Saws/N-5yc1vZc268

If you've never done it good luck. There's a ton of wires and other important do-dads behind your dash that you don't want to destroy. Building a dash requires careful planning and measuring because you can't undrill a hole. You're still going to have a big hole where the factory gauges were if you take the cluster out. As opposed to maybe wrecking your good dash consider adding a gauge panel to the bottom of your dash like a three holer that you can get at most any auto parts store or Jeg's or Summit and install whatever gauges you want in it.
 
OP
OP
mini73

mini73

Sr. Member
Joined
Aug 12, 2013
Messages
969
Hole saws...

http://www.homedepot.com/b/Tools-Ha...-Bits-Hole-Saws-Arbors-Hole-Saws/N-5yc1vZc268

If you've never done it good luck. There's a ton of wires and other important do-dads behind your dash that you don't want to destroy. Building a dash requires careful planning and measuring because you can't undrill a hole. You're still going to have a big hole where the factory gauges were if you take the cluster out. As opposed to maybe wrecking your good dash consider adding a gauge panel to the bottom of your dash like a three holer that you can get at most any auto parts store or Jeg's or Summit and install whatever gauges you want in it.

I already have 2 below my dash now. Want to get some auto meter gauges and put them in the dash. If I plan on the hole with my dash and while still in the bronco I will remove everything from behind where I will make the hole. I'm thinking with since the 5" auto meter is somewhat smaller I can fabricate some kind of plate to keep it going through the original speedometer hole.
 

JoeB458

New Member
Joined
Aug 9, 2013
Messages
48
Loc.
Springfield
I am working toward a similar setup. I used a hole saw to cut the hole for gauges. Lowes or Home Depot have them. Just be sure they are for metal.
 
OP
OP
mini73

mini73

Sr. Member
Joined
Aug 12, 2013
Messages
969
I am working toward a similar setup. I used a hole saw to cut the hole for gauges. Lowes or Home Depot have them. Just be sure they are for metal.

I got hole saws at work as I work in maintenance. just got to figure out what gauges I want to go with and what size. Also wondering if I should go with electric or keep them mechanical
 

DuctTape

Bronco Guru
Joined
Jun 20, 2008
Messages
1,148
Loc.
Bozeman, MT
I'm currently in the middle of mocking up gauges installed into wildhorses under dash cubby. Might be an option for you.
 

DuctTape

Bronco Guru
Joined
Jun 20, 2008
Messages
1,148
Loc.
Bozeman, MT
Take the dash out, not hard once you figure it out.

There are two bolts that hold the steering column to dash. Your column setup my vary but drop those bolts, remove the column support thing on firewall, disconnect the rag or ujoint, unhook yo the electrical and column comes right out.

Disconnect gauges and switches (if you get stuck on ignition switch come back here).

The dash has two bolts that also hold your windshield up, two bolts on the sides (tabs), and possibly two more at the bottom edges on either side (I had a PO that welded these on...).

I think you will find you save time in the long run pulling the dash. If you did that you could config it however you like, patch anything you want, drop a fresh coat of paint on it and voila.

If you don't want to spend that much time then I think you are better off adding some gauges to the bottom of the existing dash.
 

Digger556

Sr. Member
Joined
Aug 8, 2013
Messages
801
Just my $0.02, but in my case a full set of Autometer gauges costs more than the Dakota Digital setup and I still didn't have turn signals, check engine, high beam indicator etc. In addition, a full set of Autometers was going to be cluttered looking with my dash.

I waited for the DD set to go on sale and saved money over the Autometer.

IMG_20140506_203637_692_zpsc90ab696.jpg
 

WorkerBee

Full Member
Joined
Aug 22, 2011
Messages
224
Loc.
Northern CA
X2 on taking the dash out. It's really not that hard once you have the windshield dropped.

I made my own dash but if I didn't have the resources to do so I would have bought a blank one. I had a great experience buying gauges from Speedhut and I am really happy with them so far. They can customize just about anything you want. They're a little spendy but worth it in my opinion. They're very shallow and easy to install.

One other benefit is that the speedo is run off of GPS so there's no more cable. I was planning on doing a full write up on the gauges but didn't want to speak to soon. I wanted to give them a little more time to make sure they're reliable. So far so good though.

http://www.speedhut.com/
 

Attachments

  • 4910.jpg
    4910.jpg
    75.6 KB · Views: 155
  • 4915.jpg
    4915.jpg
    89.8 KB · Views: 162
  • 4927.jpg
    4927.jpg
    118.5 KB · Views: 162
  • 4934.jpg
    4934.jpg
    83.4 KB · Views: 152
OP
OP
mini73

mini73

Sr. Member
Joined
Aug 12, 2013
Messages
969
X2 on taking the dash out. It's really not that hard once you have the windshield dropped.



I made my own dash but if I didn't have the resources to do so I would have bought a blank one. I had a great experience buying gauges from Speedhut and I am really happy with them so far. They can customize just about anything you want. They're a little spendy but worth it in my opinion. They're very shallow and easy to install.



One other benefit is that the speedo is run off of GPS so there's no more cable. I was planning on doing a full write up on the gauges but didn't want to speak to soon. I wanted to give them a little more time to make sure they're reliable. So far so good though.



http://www.speedhut.com/


I don't have no problem with letting the windshield down has I have no top and no dash pad. I do have a full roll cage but the way it ended up when I installed it, it's not that close to the dash so I might be able to get it out. Never thought about the gauges you are talking about. Interesting. But I can not see the pics you posted
 

markw

Contributor
Bronco Guru
Joined
Sep 10, 2009
Messages
2,066
Ron, that's a great layout! I'd love to pay you for a copy, it looks like a lot of thought and work went in to that layout. Mark
 

RonJones

Contributor
Full Member
Joined
Jun 30, 2001
Messages
347

BoureeOne

Bronco Guru
Joined
Mar 28, 2011
Messages
3,068
Loc.
Madisonville, La
My route is a little unique. I am using 1948 Lincoln Continental gauges. I also found a 1948 dash, and modded it to fit into my dash. I also picked up an extra clock that is going to be converted into a tach.
 

Attachments

  • Lincoln Dash.jpg
    Lincoln Dash.jpg
    94.1 KB · Views: 98
  • Lincoln Gauges in Dash.jpg
    Lincoln Gauges in Dash.jpg
    105.5 KB · Views: 86
  • Lincoln Gauges in Dash 2.jpg
    Lincoln Gauges in Dash 2.jpg
    132.6 KB · Views: 88
  • Lincoln Gauges.jpg
    Lincoln Gauges.jpg
    56.5 KB · Views: 93
Top