• Just a reminder that you won't be able to start new posts or reply to existings posts in the Archive forum.

    This is where all the old posts go so they can still be used for reference and searched.
  • Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Car diving toward right when braking...

broncodriver99

Bronco Guru
Joined
Jan 27, 2008
Messages
4,780
Loc.
Glen Allen, VA
Brakes need adjusted some more. ;D

Are you still running the factory front drums? They can be a pain to get dialed in. My last bronco that had front drums would sometimes change lanes on me while braking. I finally tossed them in favor of a disc setup and now it stops straight every time.
 

pa69broncoguy

Sr. Member
Joined
Sep 6, 2011
Messages
566
any recent brake line replacement, sometimes when you change one rubber line the vehicle will pull. Its always a good practice to change everything in pairs
 

Kbpony

Sr. Member
Joined
Jan 31, 2012
Messages
386
If you are adjusting them yourself, take it to a gravel road or big parking lot. Step on the brakes hard enough to lock up the wheels and then get out and look at the skid marks. They should all lock at the same time. Adjust by tightening up the drums with the shortest skid marks. Repeat until they all grab together. You can adjust them yourself with a screwdriver, just stick it in the slot in the backing plate and pull down once you get it in a tooth on the adjuster wheel.
 

RustBeltRefugee

Jr. Member
Joined
Feb 25, 2011
Messages
70
Loc.
Santa Clarita
Is there any chance that air got into the system? With a dual cylinder master cylinder, If there is air in one side then it would pull. Pulling to the right could mean that there is more air in the section that applies the right front brake and probably the left rear brake. Air might be in a location that will be difficult bleed out at the calipers or wheel cylinders and it might be helpful to try bleeding it by cracking the lines at the master cylinder.
 

bronco loco

It never ends
Joined
Nov 12, 2005
Messages
2,735
Loc.
Long Island New York
If you are adjusting them yourself, take it to a gravel road or big parking lot. Step on the brakes hard enough to lock up the wheels and then get out and look at the skid marks. They should all lock at the same time. Adjust by tightening up the drums with the shortest skid marks. Repeat until they all grab together. You can adjust them yourself with a screwdriver, just stick it in the slot in the backing plate and pull down once you get it in a tooth on the adjuster wheel.

I got to remember this one when i need to adjust my rear drums, thanks;D;D;D
 

blubuckaroo

Grease Monkey
Joined
Jun 11, 2007
Messages
11,796
Loc.
Ridgefield WA
Back before the world went to front disc brakes, a lot more attention was given to front brake replacement.
Arcing the linings to the drum contour was necessary for a good brake job, that wouldn't pull when applied. Most brake facilities don't even have the equipment or knowledgeable employees to do that anymore.
The best you can do is to make sure the brake shoes are assembled correctly for the side they are on, and they are adjusted the same on both sides. Also, make sure one of the wheel cylinders isn't stuck.
 

CopperRanger

Bronco Guru
Joined
Sep 26, 2007
Messages
1,796
Mine was pulling to the right a little and I found a frozen up wheel cylinder on the right side.
 

bronconut73

Bronco Guru
Joined
Aug 7, 2012
Messages
9,919
Back before the world went to front disc brakes, a lot more attention was given to front brake replacement.
Arcing the linings to the drum contour was necessary for a good brake job, that wouldn't pull when applied. Most brake facilities don't even have the equipment or knowledgeable employees to do that anymore.
The best you can do is to make sure the brake shoes are assembled correctly for the side they are on, and they are adjusted the same on both sides. Also, make sure one of the wheel cylinders isn't stuck.

We called it truing or cam grinding the shoes to the drum.
Actually used to do it at Sears when I turned wrenches there.

The older lathe had mounts for doing it but of course as the years went by it got used less and less.
Rear drums don't generally need this.
Front drums didn't need it very often.
 
Last edited:
Top