• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Third times a charm v3.0

badmuttstang

redneck grease monkey
Joined
Oct 25, 2009
Messages
2,807
I have to say I'm jealous of your parts pile and can't wait to see yours when it's done at least done for this round
 
OP
OP
JSmall

JSmall

Bronco Guru
Joined
Feb 18, 2004
Messages
3,224
The universal top truss was a PAIN IN THE ASS!!! I got it cut out and tacked into place. The RuffStuff upper link mount is sitting in place.

 

broncoitis

Bronco Guru
Joined
Jul 23, 2010
Messages
4,449
I like the look of the truss. Where did you get the upper truss from? Planning on linking mine eventually as well! Keep the pics coming. ;D
 
OP
OP
JSmall

JSmall

Bronco Guru
Joined
Feb 18, 2004
Messages
3,224
I like the look of the truss. Where did you get the upper truss from? Planning on linking mine eventually as well! Keep the pics coming. ;D

That's the universal truss from Artec. Lots of cutting and grinding involved, but I think it looks good.
 
OP
OP
JSmall

JSmall

Bronco Guru
Joined
Feb 18, 2004
Messages
3,224
Hahahha!! You just felt my pain, those Artec Truss are a pain the ass, but seriously though!!

Just like everything else, I was over thinking it. I said "F it" and started cutting. I got it really close so I'm happy. I need to figure out what I'm going to do with the breather now because the truss blocks it.
 

Apogee

Contributor
Bronco Guru
Joined
Nov 26, 2005
Messages
6,348
Loc.
Tangent, OR
I only had about 3 good threads in my housing for the breather vent, so I just machined a little block from some 3/8" flat bar (still need to weld it to the housing and make the hard lines) to give me better thread engagement and space up the brake tee-fitting so the tube nuts aren't flat against the housing and a PITA to install.

You could notch the Artec truss for the brake hose and breather...keeping it on the drivers side assuming you're going to run your brake lines in the factory location.
 
OP
OP
JSmall

JSmall

Bronco Guru
Joined
Feb 18, 2004
Messages
3,224
I only had about 3 good threads in my housing for the breather vent, so I just machined a little block from some 3/8" flat bar (still need to weld it to the housing and make the hard lines) to give me better thread engagement and space up the brake tee-fitting so the tube nuts aren't flat against the housing and a PITA to install.

You could notch the Artec truss for the brake hose and breather...keeping it on the drivers side assuming you're going to run your brake lines in the factory location.

I'll take a look at tomorrow and see what my options are. Thanks for the suggestions
 
OP
OP
JSmall

JSmall

Bronco Guru
Joined
Feb 18, 2004
Messages
3,224
Took the axle to Warke Performance today for some advice and welding help. Badmuttstang stopped by and helped too. Ended up filling the vent hole so it will be relocated after the truss is fully welded.
 

Attachments

  • image.jpg
    image.jpg
    132.4 KB · Views: 270

badmuttstang

redneck grease monkey
Joined
Oct 25, 2009
Messages
2,807
Had a great time out there only problem is now I'm trying to figure out if I can swing a 4 link as well;D
Way to many cool things at Robert's shop.
 
Top