• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

How I Fixed My Loose Tracking Bar

EricLar80

Bronco Guru
Joined
Jun 14, 2001
Messages
2,170
Like many others, the bolt hole for the tracking bar had been egged out at the frame end. I wanted to post up what I did in case anyone was looking for ideas.

The stock bolt on a 1973 is 9/16", and the sleeve for the bushing has an OD of 3/4". I decided to convert the bolt to 5/8" and keep the sleeve the same OD.

I started out by buying a few items from McMaster:
- 4130 Tube #89955k599
- Grade 8, 5/8"-18 x 4" long bolt #91257A829; 4.25 may work better
- Grade 8, 5/8"-18 poly lock nut #97135A275
- I already had washers to make line everything up correctly.

Next I cut the tube down to the exact inside width of my frame bracket to make a new bushing sleeve - 1.775" in my case. Note that my bushing sleeve before was 1.75", which was part of the problem and didn't allow me to tighten the bolt down onto the sleeve properly. I had to drill the center of the sleeve a little because it was a too close to slip it over the bolt. I also decided to harden the sleeve by heating it with MAPP gas until it was a dull cherry red color and then immediately threw it into a can of oil.

I picked the bolt so that the un-threaded region spans the entire width of the bracket, so it was pretty long. I cut about a 1/2" of the threads off to make it the appropriate overall length and filed it down a little so the nut would thread on properly.

Drilled the hole to 5/8" with a large chuck drill, then bolted it all up and tightened to about 110 ft-lbs. The steering gear bolts to the frame had to be taken off so the gear could move to the side to fit the drill in there.

I haven't taken it out yet, but there isn't any more movement. :cool:

Eric
 

66horse

Bronco Guru
Joined
Jan 7, 2002
Messages
3,394
Like many others, the bolt hole for the tracking bar had been egged out at the frame end. I wanted to post up what I did in case anyone was looking for ideas.

The stock bolt on a 1973 is 9/16", and the sleeve for the bushing has an OD of 3/4". I decided to convert the bolt to 5/8" and keep the sleeve the same OD.

I started out by buying a few items from McMaster:
- 4130 Tube #89955k599
- Grade 8, 5/8"-18 x 4" long bolt #91257A829; 4.25 may work better
- Grade 8, 5/8"-18 poly lock nut #97135A275
- I already had washers to make line everything up correctly.

Next I cut the tube down to the exact inside width of my frame bracket to make a new bushing sleeve - 1.775" in my case. Note that my bushing sleeve before was 1.75", which was part of the problem and didn't allow me to tighten the bolt down onto the sleeve properly. I had to drill the center of the sleeve a little because it was a too close to slip it over the bolt. I also decided to harden the sleeve by heating it with MAPP gas until it was a dull cherry red color and then immediately threw it into a can of oil.

I picked the bolt so that the un-threaded region spans the entire width of the bracket, so it was pretty long. I cut about a 1/2" of the threads off to make it the appropriate overall length and filed it down a little so the nut would thread on properly.

Drilled the hole to 5/8" with a large chuck drill, then bolted it all up and tightened to about 110 ft-lbs. The steering gear bolts to the frame had to be taken off so the gear could move to the side to fit the drill in there.

I haven't taken it out yet, but there isn't any more movement. :cool:

Eric

Great write up. Had a similar problem, but went a different route. Welded hardened washers on the end to maintain bolt size. Lasted a little bit but not long.

I think the fact the new bushing come with a sleeve that is too short is a big part of the problem.

Dig your solution.

Thanks for sharing.

Cheers,
Steve
 
OP
OP
E

EricLar80

Bronco Guru
Joined
Jun 14, 2001
Messages
2,170
I have fixit washers in my drawer now. I decided to go this route first because I don't have to bring out my welder, I didn't have a 3/4 drill bit in my drawer already to use, and I can always do that if this has an issue later.

For those considering it, the McMaster tube route costs about $15, if you already have the drill bit. You need access to a lathe or a grinder in either case. The fixit washers are too long and need to be cut down to .188", or the tube needs to be cut as mentioned above.

Eric
 

RPM289

Sr. Member
Joined
Jan 4, 2008
Messages
835
Like many others, the bolt hole for the tracking bar had been egged out at the frame end. I wanted to post up what I did in case anyone was looking for ideas.

The stock bolt on a 1973 is 9/16", and the sleeve for the bushing has an OD of 3/4". I decided to convert the bolt to 5/8" and keep the sleeve the same OD.

I started out by buying a few items from McMaster:
- 4130 Tube #89955k599
- Grade 8, 5/8"-18 x 4" long bolt #91257A829; 4.25 may work better
- Grade 8, 5/8"-18 poly lock nut #97135A275
- I already had washers to make line everything up correctly.

Next I cut the tube down to the exact inside width of my frame bracket to make a new bushing sleeve - 1.775" in my case. Note that my bushing sleeve before was 1.75", which was part of the problem and didn't allow me to tighten the bolt down onto the sleeve properly. I had to drill the center of the sleeve a little because it was a too close to slip it over the bolt. I also decided to harden the sleeve by heating it with MAPP gas until it was a dull cherry red color and then immediately threw it into a can of oil.

I picked the bolt so that the un-threaded region spans the entire width of the bracket, so it was pretty long. I cut about a 1/2" of the threads off to make it the appropriate overall length and filed it down a little so the nut would thread on properly.

Drilled the hole to 5/8" with a large chuck drill, then bolted it all up and tightened to about 110 ft-lbs. The steering gear bolts to the frame had to be taken off so the gear could move to the side to fit the drill in there.

I haven't taken it out yet, but there isn't any more movement. :cool:

Eric

Can we get some pic's of this mod? "Sounds" good :)
 
OP
OP
E

EricLar80

Bronco Guru
Joined
Jun 14, 2001
Messages
2,170
You will have to use your imagination. I didn't take pictures, and I do not have the ability to upload images.

Eric
 
Top