• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Edelbrock carb install

deltabronco

Bronco Guru
Joined
Dec 27, 2005
Messages
1,100
I was about to install my 1405 and was wondering is there supposed to be any kind of spacer or adapter that fits in between the carb and the intake? ( other than the gasket) I lined the carb up today and it looks like it should just bolt straight on to the manifold.
 

rguest3

Bronco Guru
Joined
Dec 13, 2012
Messages
3,780
If you have enough height clearance to install a Phenolic spacer, I would recommend it.
 

valveamp

Full Member
Joined
May 30, 2011
Messages
287
I've had some heat issues with my Autolite 4100. I just installed a 1/4" spacer from Cool Carb yesterday. I'm still testing it out. So far, so good. A while back, I installed a 1" spacer and it was tool tall, the air cleaner hit the hood. I recommend some type of heat suppression.

http://www.coolcarb.com/
 

Master Chief

Contributor
Bronco Guru
Joined
Nov 24, 2006
Messages
1,312
Benefits?


It helps prevent fuel from boiling out of the carb. I had this issue until I removed a previous owner installed aluminum spacer and installed the Edelbrock spacer...problem solved.

Info below is step 14 on this document: http://www.edelbrock.com/automotive/misc/tech-center/install/1000/1405.pdf

When restarting the vehicle, after it has been sitting for 10-30 minutes, you may experience some difficulty starting. The result
will be similar to a flooded carburetor. To help eliminate or minimize this issue, the use of an Edelbrock Heat Insulator Gasket
Part Number 9266 (sold separately) is highly recommended. For additional heat insulator selections please visit www.edelbrock.com.
 

blubuckaroo

Grease Monkey
Joined
Jun 11, 2007
Messages
11,796
Loc.
Ridgefield WA
Thanks Master Chief, I was typing as you were answering...;)

Engines will transfer heat into the carb. It becomes a problem when the heated engine is shut down and there is no longer air/fuel flowing through it.
Modern fuel boils at a lower temperature than back when these cars were born. The fuel can boil over, and run out of the float bowl and right down into the intake manifold. This creates a flooded start problem.

A spacer will help isolate the carb from that hot motor.

Here's one made for a four barrel on a dual plane divided plenum manifold. It's also available with four holes and open plenum depending on your needs. Since it's actually just a very thick gasket, no additional gasket is needed for this one.

http://www.summitracing.com/parts/edl-9266/overview/
 
Last edited by a moderator:

savage

Bronco Nut
Joined
Apr 18, 2007
Messages
2,483
Loc.
Renton
When I put my 1405 on ,I had to put a spacer on to clear the linkage, edlebrock manifold and c-4 kick down linkage.
 

savage

Bronco Nut
Joined
Apr 18, 2007
Messages
2,483
Loc.
Renton
Hey deltabronco ,I went to your garage and see you have a tall intake, and it look's like yours will clear the linkage. What intake manifold?
 
OP
OP
deltabronco

deltabronco

Bronco Guru
Joined
Dec 27, 2005
Messages
1,100
Local company did the build so I'll have to look and see what they put on.
 

broncnaz

Bronco Guru
Joined
May 22, 2003
Messages
24,342
Here's a common adapter for edelbrocks that have been on broncos.:eek: Couldnt resist. Hope you have good luck with the edelbrock.
 

Attachments

  • Trashcan.jpg
    Trashcan.jpg
    32.4 KB · Views: 118

HB73

Sr. Member
Joined
Nov 24, 2012
Messages
788
I didn't have a spacer on mine. Shut her off at the gas station to fuel up. Went to restart, was sluggish and hard, backfired through the carb and caught on fire. A quick blast from the fire extinguisher put her out. Carbs off to rebuild tomorrow, could have been prevented with a spacer? I don't really know, but can't hurt to try.
 

BronCowie

Contributor
Old Timer
Joined
Apr 24, 2007
Messages
8,291
Loc.
Vancouver, WA
A local guru recommended that I put two gaskets in to help prevent percolation. Been running great as of 20K miles ago. ...and yes, I did replace my fuel line since I took this picture. :p
 

Attachments

  • Carb Gaskets50.png
    Carb Gaskets50.png
    151.1 KB · Views: 147
Top