• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Fuse Box Replacement

BroncoJimbo

Contributor
Long-term owner
Joined
Jun 11, 2014
Messages
291
Loc.
North GA
Hey Gang,
This has been the state of my old fuse box for many years. I would say it's less than optimum %)



I am thinking of replacing the fuse box with an aftermarket one that uses blade fuses. As anyone else done this?
 

mtxride

Full Member
Joined
Jun 14, 2009
Messages
157
Loc.
San Antonio
Nice! I'm interested in this as well. Only two fuses in my main block are being used and I have a bunch of in-line fuses that I want to clean up. I've been looking into the Blue Sea Systems blocks:
https://www.bluesea.com/products/category/16/61/Fuse_Blocks/ST_Blade
They seem well built and they have multiple options, even a block with dual buses. So you can run switched ignition off one bus and constant 12v off the other.
 

omureebe

Contributor
Sr. Member
Joined
Jun 18, 2013
Messages
419
I picked up an accessory fuse block out of a F250 that had provisions for relays, and rewired my Bronco, putting the block on the passenger side wheel well. It's at the body shop now, so no photo available, but just do a google search on F250 accessory fuse and you'll see it. What is nice, to me, is one place with dedicated fuses and relays in an OEM box. And I think it looks weird to have a fuse box in your glove box...
 

ObscureMachine

Seatbelt Orifice Officer
Joined
Sep 28, 2006
Messages
3,998
Loc.
World Headquarters
I used this blue sea fuse block under the hood to power various things. Works great. No problems.
 

Attachments

  • 5026.jpg
    5026.jpg
    80.7 KB · Views: 166

broncnaz

Bronco Guru
Joined
May 22, 2003
Messages
24,342
I would take a good hard look at your whole wiring system before pulling the trigger on a fuse box. Just make sure your wiring is good enough to justify it. You may benefit from a whole new wiring harness vs just a fuse box.
 

ObscureMachine

Seatbelt Orifice Officer
Joined
Sep 28, 2006
Messages
3,998
Loc.
World Headquarters
I would take a good hard look at your whole wiring system before pulling the trigger on a fuse box. Just make sure your wiring is good enough to justify it. You may benefit from a whole new wiring harness vs just a fuse box.

Agreed. I just wasn't at the place to go with a new harness. A fuse box temporarily addressed some power needs and some potential safety (fire) issues. A new harness is on the list.
 
OP
OP
BroncoJimbo

BroncoJimbo

Contributor
Long-term owner
Joined
Jun 11, 2014
Messages
291
Loc.
North GA
Thanks Guys.
I am not ready to do a full wiring job at this point either. I am trying to clean up some of the poor wiring decisions I have made over the 26 years I've owned this beast. I don't mind the stock location and I really don't need more than a few additional circuits. I was hoping to find a fuse box that has the connectors behind the panel (like the original). I might have to scavenge one from a newer car as omureebe suggested.
 

brianstrange

Bronco Guru
Joined
Nov 22, 2011
Messages
1,626
Thanks Guys.
I am not ready to do a full wiring job at this point either. I am trying to clean up some of the poor wiring decisions I have made over the 26 years I've owned this beast. I don't mind the stock location and I really don't need more than a few additional circuits. I was hoping to find a fuse box that has the connectors behind the panel (like the original). I might have to scavenge one from a newer car as omureebe suggested.

I made the changeover on my 67 mustang. I used two 4 position blocks that clip together, one for Battery, the other for accessory. They cost about $5 each, and are available at Advance Auto. The downfall is they are not waterproof.

What's wrong with your fuse box? If you have wiring issues, I would consider installing an aux fuse box, but as others have suggested, a new harness will go a long way. There are affordable products out there like EZ wire, that can get it done for under $200 with a panel.
 

mtxride

Full Member
Joined
Jun 14, 2009
Messages
157
Loc.
San Antonio
Jimbo, I was in the same situation you are in. I ended up buying Hella box (link below) and it has worked great. I have room for extra fuses now. And I wired it up so there is constant power for a few fuses and switched power to other fuses.http://www.rallylights.com/hl62941-atc-fuse-box-12-gang-waterproof.html

That's exactly what I've been looking for. Although I can't seem to find anything about it. Do you happen to know, or have a link to any more information about it? Max amps per circuit, bus, block? Thanks.
 

Justafordguy

Bronco Guru
Joined
Sep 26, 2009
Messages
6,255
I used a Blue Sea fuse block with a dedicated power and ground feed for some accessories but used a simple blade fuse holder to replace the stock fuse box.
 

Attachments

  • 2014-12-20 15.02.05sm.jpg
    2014-12-20 15.02.05sm.jpg
    187.1 KB · Views: 345

ObscureMachine

Seatbelt Orifice Officer
Joined
Sep 28, 2006
Messages
3,998
Loc.
World Headquarters
I used a Blue Sea fuse block with a dedicated power and ground feed for some accessories but used a simple blade fuse holder to replace the stock fuse box.

I kept mine mounted to the inner fender because most of my power needs were under the hood, and I didn't want to run a bunch of wires into the cab. But I like what you did here.
 

Justafordguy

Bronco Guru
Joined
Sep 26, 2009
Messages
6,255
I kept mine mounted to the inner fender because most of my power needs were under the hood, and I didn't want to run a bunch of wires into the cab. But I like what you did here.

Thanks, I thought about leaving it under the hood but it turned out that most of my accessories are inside and this setup required less wires through the firewall. I have a large fuse on the wire that feeds the larger fuse panel, it's right by the battery.
 

suckerpunched

Sr. Member
Joined
Aug 24, 2006
Messages
882
heres the pictures. the one from the back side didn't turn out good, but you get the idea.
 

Attachments

  • 100_2953.jpg
    100_2953.jpg
    75.1 KB · Views: 234
  • 100_2954.jpg
    100_2954.jpg
    50.2 KB · Views: 207
Top