• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

lars bars- no bend?

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
You might have to re-engineer some of the geometry, but I don't see why they could not be made to work as a straight bar.
But why do you really want to go to all the trouble of fabbing up new radius arms and not do the bend? It's mainly for tire clearance for keeping that wonderful Bronco turning radius.
If that's not a big deal to you, then you won't be upset. What size tires you planning to run?

Anyway, I'm sure some of the engineering types here will chime in with some specific recommendations about it.

Good luck.

Paul
 
OP
OP
P

PABrian

Full Member
Joined
Aug 6, 2003
Messages
165
Loc.
North central PA
having never seen a set in person, i was just wondering how much difference the 9* bend in them really amounted to. I was thinking perhaps i could simply bring them closer together slightly at the frame end. don't know if it would work, though
 

nvrstuk

Contributor
Just a Bronco driver for over 50 yrs!
Joined
Jul 31, 2001
Messages
10,622
Loc.
PNW
Why not have a bend in them? Curious...
 
OP
OP
P

PABrian

Full Member
Joined
Aug 6, 2003
Messages
165
Loc.
North central PA
never really liked the idea of bent links, in suspension or steering. makes a weak spot. I'm not busting on anyone who runs them bent, just my personal preference
 

gddyap

Bronco Guru
Joined
Mar 8, 2005
Messages
1,334
Loc.
Mtn View, CA
The bend matches the angle of the stock arms and allows the end of the arms to be parallel to the frame where it connects. Without the bend, the arms either have to be the same length as stock to mount under the frame or mount inside the frame if the arms are longer than stock. The 6" (?) of added length of the parallel section is what gives it the balance of off-road and on-road performance. Longer than stock for added leverage for off-road flex, but not so long that you get excessive body sway on-road.
 

lars

Contributor
Been here awhile
Joined
Jun 29, 2001
Messages
3,334
Loc.
NorCal flatlands
Another reason for the bend: If the extended arms are straight, then the angle between the arms is less. Which results in an outward moment being placed on the C bushings in the plane of the arms. It's not a lot, but it would make assembly more difficult, and the constant load would possibly (which is to say not verified by experiment) lead to shorter life for the bushings.

Oh yeah, then there is the matter of tire clearance... that's not trivial. With my 35" tires and correctly (stock) back spaced wheels, I have to allow the tires to scrape the radius arms to maintain something resembling the wonderful stock early Bronco turning radius. Without the bend it would be worse.

Best for a great 2016, y'all!
 

ZOSO

Sr. Member
Joined
Jan 25, 2003
Messages
385
I built a set of these last year. Still have yet to install them but it's on the list for this winter. We designed them as a group here and made a jig. A local engineer ran all the numbers and in the end we came up with adding an extra degree of caster to them. We went with a metal cloak duroflex joint. http://www.metalcloak.com/Jeep-Suspension-Builders-Parts-s/235.htm Initially we were not going to put any bend in them for strength reasons. But the metal cloak joints shouldn't be side loaded like they would see if the arms were straight and pulled out to be even with the frame.
 

welndmn

Bronco Guru
Joined
Nov 12, 2001
Messages
2,112
With the 1/4 wall tube of the Lars bars, a cheap harbor freight tube kinker does a great job of bending them too.
 

70_Steve

Old Guy
Joined
Dec 13, 2002
Messages
8,317
I went to an old school independent exhaust shop that had one of those huge hydraulic exhaust tubing benders. Only cost me $20.
 

drtodd

New Member
Joined
May 11, 2011
Messages
12
Loc.
Eagle
I am not bending mine. The following issues will allow me to use the sexier straight (!) look.

1. full width axles. The wedges aim directly at where the new pivot point is.
2. negative offset Humvee rims. 37" tires. Not tested the turning radius yet, but I believe it will clear.
3. extra length arms. I am adding 12-14 inches to the arms from old pivot to new pivot
4. I am correcting the caster by bending the upper part of the forged existing arm by about ten degrees to compensate for the six inch lift. This will also straighten the massive forwrd bow on my coil springs. I still need to address the issue of locating the lower spring cups directly under the uppers. Or moving the uppers out. Or angling the lowers inward to aim the spring directly at the upper cup. Any ideas on that?
 

Apogee

Contributor
Bronco Guru
Joined
Nov 26, 2005
Messages
6,348
Loc.
Tangent, OR
I am not bending mine. The following issues will allow me to use the sexier straight (!) look.

1. full width axles. The wedges aim directly at where the new pivot point is.
2. negative offset Humvee rims. 37" tires. Not tested the turning radius yet, but I believe it will clear.
3. extra length arms. I am adding 12-14 inches to the arms from old pivot to new pivot
4. I am correcting the caster by bending the upper part of the forged existing arm by about ten degrees to compensate for the six inch lift. This will also straighten the massive forwrd bow on my coil springs. I still need to address the issue of locating the lower spring cups directly under the uppers. Or moving the uppers out. Or angling the lowers inward to aim the spring directly at the upper cup. Any ideas on that?

Have you thought about your pinion angle? Just rolling the axle back is great for caster, but will kill your front pinion angle, especially with so much lift. I'm currently putting full width F150 axles under mine with 3.5" lift and will be rotating the knuckles so that I can have good caster and pinion angle.
 

garberz

Bronco Influencer
Joined
Jun 24, 2007
Messages
6,864
Loc.
Conejo Valley, Ca.
Have you thought about your pinion angle? Just rolling the axle back is great for caster, but will kill your front pinion angle, especially with so much lift. I'm currently putting full width F150 axles under mine with 3.5" lift and will be rotating the knuckles so that I can have good caster and pinion angle.

If he's doing a hi-pinion, he can roll it back plenty, and the pinion angle still won't be an issue like a LP44.

Mark
 

drtodd

New Member
Joined
May 11, 2011
Messages
12
Loc.
Eagle
Yeah that short little drive shaft is kind of scary. I hope that double cardon does its job!

I'll get some photos up soon, but Saturday, it's Jamaica!
 

Apogee

Contributor
Bronco Guru
Joined
Nov 26, 2005
Messages
6,348
Loc.
Tangent, OR
If he's doing a hi-pinion, he can roll it back plenty, and the pinion angle still won't be an issue like a LP44.

Mark

It may not be a binding issue, but it might shake like a wet dog at speed. My plan is to stick with a double cardan shaft up front with the pinion basically in line with the shaft to avoid any issues. My current setup with a low-pinion D44 and long travel arms leaves a lot to be desired with respect to my front pinion angle, and I'm not a huge fan of the offset u-joints in practice. Great band-aid, but not very fun at speed in 4WD.
 

ntsqd

heratic car camper
Joined
Jan 30, 2005
Messages
5,970
Loc.
Upper SoKA
If you're going to that much work already, do it right - cut-n-turn the C brackets. Don't try to correct Caster in the arms.
 

drtodd

New Member
Joined
May 11, 2011
Messages
12
Loc.
Eagle
Hope that double cardon does its job! My six inch lift left the existing caster at 5 degrees negative and the spring bowed forward freakishly.
 
Last edited:
Top