• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

lars bars- no bend?

drtodd

New Member
Joined
May 11, 2011
Messages
12
Loc.
Eagle
If he's doing a hi-pinion, he can roll it back plenty, and the pinion angle still won't be an issue like a LP44.

Mark

Yes it's a high pinion. I don't see rolling that diff down ten degrees as much of a problem.
 

needabronco

Bronco Guru
Joined
Jul 2, 2004
Messages
6,411
Loc.
Prescott/Farmington
I'm building another set right now after breaking my 10 year old Lars Bars. I've built several sets and have always had exhaust shops do the 9 degree bend. The most I've been charged to date was $10 to bend 6 pieces. The shop I'm using now is $2.50 per bend. It literally takes them about 30 seconds per tube and their exhaust bender doesn't even sound like it's working hard.
 

drtodd

New Member
Joined
May 11, 2011
Messages
12
Loc.
Eagle
If you're going to that much work already, do it right - cut-n-turn the C brackets. Don't try to correct Caster in the arms.

Cut the axle tubes and reweld to the proper caster? I'm afraid that's above my pay grade.

Here's what I did. Cut the stock radius six inches longer than the existing Lars recipe calls for, removed the web down to the existing clamp bend, and bend the upper member up ten degrees. I later dialed that back to five degrees.
 

ntsqd

heratic car camper
Joined
Jan 30, 2005
Messages
5,970
Loc.
Upper SoKA
Cut the C brackets loose from the axle tubes, check/set the pinion angle (bent radius arms favoring caster will screw that up), Set caster and weld the C's to the axle tubes. Sure sound like less work and will result in a stronger assembly, but it's done so I guess we'll see how well it works and lives.
 

KyleQ

Bronco Guru
Joined
Apr 24, 2008
Messages
5,480
Interesting - my father build very similar arms without the bend with far heavier tubing and sleeved the arms further up, but similar deal.

20160403_143341_zpsypu7vc46.jpg

IMG_20130726_174845_355_zpsb55e4ec4.jpg

IMG_20130726_174852_691_zps3de49870.jpg

20160403_161332_zpsuf9mulfl.jpg
 

ntsqd

heratic car camper
Joined
Jan 30, 2005
Messages
5,970
Loc.
Upper SoKA
Don't think they can be called "Lars Bars" at that point, they're not the same thing.

I have wondered about adding a strap of the same thickness as the bottom flange of the OE radius arm to the full length of the bottom on these arms. Butt the strap up against the end of the flange. Partly to create a "rub rail" (for those who grind them on rocks) and partly to eliminate the stress riser created by the step at end of the flange.
 

drtodd

New Member
Joined
May 11, 2011
Messages
12
Loc.
Eagle
Photos?

Anybody know how to upload photos? The FAQ's aren't much help. I don't see a "manage attachments" button as it says.
 

bronconut73

Bronco Guru
Joined
Aug 7, 2012
Messages
9,919
Anybody know how to upload photos? The FAQ's aren't much help. I don't see a "manage attachments" button as it says.

Become a contributor. Its only like $12 bucks a year, then you can upload photos in a normal fashion.
 

OPCJeff

Jr. Member
Joined
Apr 30, 2016
Messages
99
Loc.
Orange, CA
So I have the duff arms on mine and when you run the high lift it really does mess with the pinion angle. What I noticed most is that the arms are no longer at the same radius as the front driveshaft so as the diff drops it stays horizontal putting a greater angle to the u joint. So basically it will bind quicker. The double cardones help with vibration but I don't think they help much h with u joint bind because of the extreme angle. I'm sure the high pinion will help this a lot but at the same time you may still have issues at full suspension drop. I would seriously consider getting the k buckles twisted. Then you have the right caster plus the right pinion angle
 

KyleQ

Bronco Guru
Joined
Apr 24, 2008
Messages
5,480
I've got no issues with Cage arms and pinion angle-
20150726_120712_zpsc61x2r1x.jpg
 

patrickk1

Jr. Member
Joined
Mar 7, 2011
Messages
135
Loc.
Cambridge
When I priced out the parts to make Lars Bars, it wasn't going to cost that much more to just buy parts to 3link the front suspension.
 

ntsqd

heratic car camper
Joined
Jan 30, 2005
Messages
5,970
Loc.
Upper SoKA
When I priced out the parts to make Lars Bars, it wasn't going to cost that much more to just buy parts to 3link the front suspension.
For crawling I don't see any gain for the extra effort. For high speed dirt it might be worth the trouble depending on your driving style.
 

needabronco

Bronco Guru
Joined
Jul 2, 2004
Messages
6,411
Loc.
Prescott/Farmington
With Lars bars your bend will cost a few bucks at an exhaust shop to get done and it will get you more turning radius. Worrying about this 'extreme' pinion angle at maximum droop is almost pointless for 99% of us as we don't drive at maximum axle droop. You might go a few feet like that at most? I've run Lars bars for years and have beat the snot out of them (I even broke a set bombing down too many washes), I just built another set a couple of weeks ago...

Lar's (the original designer) is an engineer and has done his homework on this design. I even have the cad drawings and a jig built to Lars' spec's. They are fairly simple to build if you have the time and a few tools, and are confident in your welding ability. If this was some back woods engineered design I'd be concerned, but this is a tried and true setup that flat out works!
 
Top