• Just a reminder that you won't be able to start new posts or reply to existings posts in the Archive forum.

    This is where all the old posts go so they can still be used for reference and searched.
  • Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

What Degree for Engine Angle?

fordguy

Contributor
Bronco Guru
Joined
Jan 23, 2005
Messages
6,361
mocking up motor, trans and t/c. what is recommended angle on intake? Another question is how do i keep the engine/trans straight, i have read on here where there will be an offset to one side? I am thinking of measuring from block to inside of frame front to back? Or do i tack everything up install driveshaft and check angles?
 

toddz69

Sponsor/Vendor
Bronco Guru
Joined
Nov 28, 2001
Messages
11,222
I don't have the Ford spec handy (it appeared in one of the later years shop manuals) but as I recall it was 4.xx deg. sloping towards the back. I've always kept mine around 5 deg.

Todd Z.
 
OP
OP
fordguy

fordguy

Contributor
Bronco Guru
Joined
Jan 23, 2005
Messages
6,361
I don't have the Ford spec handy (it appeared in one of the later years shop manuals) but as I recall it was 4.xx deg. sloping towards the back. I've always kept mine around 5 deg.

Todd Z.

Todd, thanks, that is what I was thinking. it wont matter as much for fuel as it will for pinion angle alignment because I have efi. Can I use the frame rails and block measurements to keep it square in the frame when I mount my custom crossmember (np205/awd 4r70)? I would think where the oil pan bolts on would be straight and measure fore and aft.
 

toddz69

Sponsor/Vendor
Bronco Guru
Joined
Nov 28, 2001
Messages
11,222
Todd, thanks, that is what I was thinking. it wont matter as much for fuel as it will for pinion angle alignment because I have efi. Can I use the frame rails and block measurements to keep it square in the frame when I mount my custom crossmember (np205/awd 4r70)? I would think where the oil pan bolts on would be straight and measure fore and aft.

Sounds like a good plan to me.

Todd Z.
 

Crush

Contributor
Bronco Guru
Joined
May 30, 2007
Messages
3,463
Loc.
Greenbottom, WV
If you use a carb intake when setting the engine in make sure the carb mounting surface is level front to back and side to side. This will give you the proper engine angle. The. You can switch out to your fi intake later. Might be better setting it with carb intake neway. Less stuff in the way. That is what i did with mine and everything turned out right. At least in my eyes. Lol
 
OP
OP
fordguy

fordguy

Contributor
Bronco Guru
Joined
Jan 23, 2005
Messages
6,361
If you use a carb intake when setting the engine in make sure the carb mounting surface is level front to back and side to side. This will give you the proper engine angle. The. You can switch out to your fi intake later. Might be better setting it with carb intake neway. Less stuff in the way. That is what i did with mine and everything turned out right. At least in my eyes. Lol

i understand about the level surface, but i dont understand why it make a difference between fi and carb intake. fi intake is setting on the engine at the moment and i do have a carb intake.
 
OP
OP
fordguy

fordguy

Contributor
Bronco Guru
Joined
Jan 23, 2005
Messages
6,361
If you use a carb intake when setting the engine in make sure the carb mounting surface is level front to back and side to side. This will give you the proper engine angle. The. You can switch out to your fi intake later. Might be better setting it with carb intake neway. Less stuff in the way. That is what i did with mine and everything turned out right. At least in my eyes. Lol

i understand about the level surface, but i dont understand why it make a difference between fi and carb intake. fi intake is setting on the engine at the moment and i do have a carb intake.
 

Crush

Contributor
Bronco Guru
Joined
May 30, 2007
Messages
3,463
Loc.
Greenbottom, WV
The fi intake is not angled like the carb intake. If you look at both intakes side by side the carb will be angled to the front and the fi ports will be level with the sides of the intake. If you look at an installed fi motor. The back of the plenum will be lower than the front. Looking at installed carb motors the ir cleaner is level. Is that clear as mud? Lol.
 
OP
OP
fordguy

fordguy

Contributor
Bronco Guru
Joined
Jan 23, 2005
Messages
6,361
that is as clear as gumbo mud LOL. no i understand the angle on the carb intake, but did not realize the fi was level. I have a performer intake i can use.
 
Top