• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Largest ties with stock front fenders

Timmy390

Contributor
Bronco Guru
Joined
Jan 1, 2011
Messages
5,948
Loc.
Conway, AR
Did some searching but only found info in the rear uncut fenders.

I just finished up my project of replacing my cut front fenders with stock replacements. Spent about 8 hours on each getting them fitting with the original doors and grill but that's a different thread. Spoiler alert, they came out GREAT.

My rear fenders are cut however I plan on grafting in the stock front metal flairs to the rears. I'm not looking to tackle that project till next fall/winter but I need tires. My current tires are not going to last another year.

So the question is, what's the biggest tires anyone is running with stock front fenders. I've got a 2.5 SL and 1 inch BL. Currently running 31's (265/75/R16) MT's right now.

I think a 33 will fit but was looking at 34's. Did some mock up in the back and 34's just look huge. I want to run 285/75/R17's (a 34) on Method NV rims.

Tim
 

SHX669

Bronco Guru
Joined
Jan 9, 2009
Messages
1,997
Well I've got a 2 1/2' Susp lift and 1" body lift and I'm running 33x12.50x15s . They rubbed a little on the front " rolled in lip " when on odd angles so i just cut a little out of that area.
I've got 10" wide wheels so maybe 8 " wide or maybe 33x10.50s wont rub . This at least gives you a parameter for what WILL rub.
 
OP
OP
Timmy390

Timmy390

Contributor
Bronco Guru
Joined
Jan 1, 2011
Messages
5,948
Loc.
Conway, AR
The Method NV rims are 8.5's in a 17 inch

The 34 inch 285/75/17's have a cross section of 11.50 The 33 inch 285/70/17 also has a 11.50 cross section.

Tim
 

Rustytruck

Bronco Guru
Joined
Feb 24, 2002
Messages
10,872
My experience on my Bronco.

31-10.50-15" on an 8" rim will rub on the lower part of the front fender when you turn fully. You have to cut out the inside corner and remove the fender support.

33" 10.50 - 15" on an 8" rim will not only rub at the lower front it will also hit the vertical edge of the inner fender well if you bump up the wheel hard enough. It will put a razor like slice through the tread blocks. Both of these areas can be trimmed without showing on the outside of the fender.

The same trimming of the fender and rear inner fender will allow you to clear 33"-12.50-15" on 8" rims.

I have never used 10 inch wide rims so I can't comment on those.
 

SHX669

Bronco Guru
Joined
Jan 9, 2009
Messages
1,997
As all things Bronco your results may vary - i didn't have to remove my fender supports It looks like I stopped about 1" short on one side and 3/4" short on the other.
I try to never say anything definitive about these things - LOL
 

69broncofun

Bronco Guru
Joined
Nov 22, 2016
Messages
1,386
I am thinking of doing this to mine. Where did you get your front fenders if I may ask?

Thanks
 
OP
OP
Timmy390

Timmy390

Contributor
Bronco Guru
Joined
Jan 1, 2011
Messages
5,948
Loc.
Conway, AR
I am thinking of doing this to mine. Where did you get your front fenders if I may ask?

Thanks

I got mine through Dennis Carpenter (Blue Oval Industries) made in Taiwan per the sticker on the inside of the fenders. You can't beat $194 each to the door on fenders. $14.99 flat rate shipping. I ordered them separately thus paid $14.99 more than I could have.

They fit OK overall but need tweaking. I spent about 8 hours each getting them perfect. had to cut a few spot welds and reweld, bend here and there and do some tapping with a hammer. Here's the thread where I talked about them. Nothin hard but if you don't have a welder then you may have bad fitting fenders.
http://classicbroncos.com/forums/showthread.php?p=2923144

The fenders are shaped fine it's the welded mounting flanges that are off just a bit. I had to oblong a few holes too.

But they look great. I cut the holes for the side marker lights and got them installed. Have not drilled for the "Bronco" script yet. Will do that on a rainy day next month. I need to order a new script (one of mine is broken) and get new clips.

Tim
 

69broncofun

Bronco Guru
Joined
Nov 22, 2016
Messages
1,386
I got mine through Dennis Carpenter (Blue Oval Industries) made in Taiwan per the sticker on the inside of the fenders. You can't beat $194 each to the door on fenders. $14.99 flat rate shipping. I ordered them separately thus paid $14.99 more than I could have.

They fit OK overall but need tweaking. I spent about 8 hours each getting them perfect. had to cut a few spot welds and reweld, bend here and there and do some tapping with a hammer. Here's the thread where I talked about them. Nothin hard but if you don't have a welder then you may have bad fitting fenders.
http://classicbroncos.com/forums/showthread.php?p=2923144

The fenders are shaped fine it's the welded mounting flanges that are off just a bit. I had to oblong a few holes too.

But they look great. I cut the holes for the side marker lights and got them installed. Have not drilled for the "Bronco" script yet. Will do that on a rainy day next month. I need to order a new script (one of mine is broken) and get new clips.

Tim

has anyone heard of these ?? http://www.rockauto.com/en/catalog/ford,1969,bronco,5.0l+302cid+v8,1105355,body,fender,1380
 

duffymahoney

Contributor
Bronco Guru
Joined
Apr 26, 2015
Messages
2,734
285/75-17 fit fine in the stock front fenders with that much bs. I don't know about wider.
 
Top