Community
Buy / Sell
James Duff Rust Bullet Sexton Offroad
Bronco Tech
Ford Bronco Parts - Classic Vintage Early Bronco Parts
  • Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.
Timmy390

Timmy390

Contributor
Bronco Guru From Conway, AR
Joined
Last seen
Messages
5,564
Gallery
10

Latest activity Postings Images Gallery Albums About

    • Timmy390
      Timmy390 replied to the thread Should I Replace Timing Chain?.
      I'm not sure you can even buy nylon timing sets anymore.....but while your in there might as well check. PO's do some crazy...
    • Timmy390
      Timmy390 replied to the thread Should I Replace Timing Chain?.
      1. Yes 2. Yes Replace nylon gear teeth get hard and brittle thus break. 3, Leave it alone Tim
    • Timmy390
      Timmy390 replied to the thread Oil Leak on Filter.
      Make sure it's not a leak at the oil pressure sending unit and it's dripping down on the filter. Tim
    • Timmy390
      Timmy390 replied to the thread 5.8 zf tranny qestion?.
      Hummmm. How about putting pressure on the system with a radiator pressure tester? Make it leak more maybe and make it easier to find? Tim
    • Timmy390
      Timmy390 reacted to 73azbronco's post in the thread Engine Mod Recommendations with Like Like.
      you can do an explorer swap using a carb and front dress to get you bigger alternator, place of AC compressor, and serp belt which is...
    • Timmy390
      Timmy390 replied to the thread Engine Mod Recommendations.
      Yes with the right flex plate/flywheel. Old engine is 28oz and Explorer is 50oz balance. Engine, Flywheel/flex plate and harmonic...
    • Timmy390
      Timmy390 replied to the thread Engine Mod Recommendations.
      Building the old block is throwing good money after bad IMO. The only thing you plan to reuse it the block. Newer blocks are one piece...
    • Timmy390
      Timmy390 replied to the thread 5.8 zf tranny qestion?.
      Does the engine run? if so, add UV dye to the cooling system. I did this and tracked down a leak or three. The photo shows the last...
      • 20160825_084640.jpg
    • Timmy390
      Timmy390 replied to the thread Engine Mod Recommendations.
      Buy an Explorer with 302 and transplant it. Good heads, good cam, good cooling when using the front dress. Upgraded alternator, PS and...
    • Timmy390
      Timmy390 replied to the thread 5.8 zf tranny qestion?.
      One half dozen the other. I've done it both ways. My W goes in and out with ease. Same with the M5ODR2. I had the trans in and out...
    • Timmy390
      Timmy390 replied to the thread Steering Box Suggestions.
      Weakness. The Borgeson box is also known as the Delphi box and was designed for on road use. Think it came on Xterra's and the likes...
    • Timmy390
      Timmy390 replied to the thread 351w Swap.
      I'm not sure someone who did as you say would rate the title of "mechanic". I would be calling him "the defendant". To your question...
    • Timmy390
      Timmy390 replied to the thread Crossed my power steering lines..
      Don't feel like the lone ranger. Many of us have done this. I was so worried about it when I went to the Delphi box I put the front up...
    • Timmy390
      Timmy390 replied to the thread Steering Box Suggestions.
      Yup....unless going rock crawling the Borgenson box will serve you well. I've been running one for years. Tim
    • Timmy390
      Timmy390 reacted to 1969's post in the thread Steering Box Suggestions with Like Like.
      I have the borgeson box and it’s big and beefy with all new parts. Plus only about $500.
    Show older items
  • Loading…
  • Loading…
  • Loading…
  • Loading…
  • Loading…
Top