• Just a reminder that you won't be able to start new posts or reply to existings posts in the Archive forum.

    This is where all the old posts go so they can still be used for reference and searched.
  • Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

gear reduction

sprdv1

Contributor
REBEL
Joined
Mar 8, 2007
Messages
81,996
Good luck big boy.. Just do what you got to do :)
 

rjrobin2002

Contributor
Bronco Guru
Joined
Oct 13, 2007
Messages
2,951
So its like a doubler and you could put it in low range and your dana 20 in low range to have basically a 5:1 low range? But it will add 6 inches to your drivetrain and you will have to shorten your rear and lengthen your front shaft.
 

ScanmanSteven

Bronco Guru
Joined
Dec 19, 2010
Messages
1,129
I have an earlier version that used the BW1356 and couldn't be happier with it. I was making major changes to my drivetrain so the new driveshafts were just part of the change. For the price, Behemoth can't be beat! For the quality, Behemoth can't be beat! For innovation, Behemoth can't be beat! For the wait time, Behemoth can't be beat! Clarifying the last one, I've never met Jacob but have bought 2 units from him, I think he's a brilliant machinist but his delivery can be long, the last one I bought he sent me pictures of the finished product before I paid for it but unfortunately one section was wrong which he replaced, but it took 3 months to get the replacement.

I would recommend his products, I would buy from him again, just give yourself plenty of lead time and you won't be disappointed.
 

68rockcrawler

Bronco Guru
Joined
Sep 18, 2006
Messages
1,417
Doesn't this box replace the adapter between tranny and transfer case? If so it wouldn't lengthen the drivetrain at all. I had been considering getting a Blackbox from Northwest Fab (http://www.northwestfab.com/BlackBox-i_p_12.html), but this one is a lot cheaper. There has to be some reason for the differing prices. Maybe the blackbox uses new gears vs re-used gears in the Behemoth?

I also thought that this made it so you could skip the adapter when putting the Dana 20 on the back of a different tranny such as a 4R70W. It seems like the info on the Behemoth and NWF sites is a little lacking.
 

Broncobowsher

Contributor
Total hack
Joined
Jun 4, 2002
Messages
37,112
So I read that as a $700 kit that you build with parts from a NP2xx transfer case as a donor.
 
OP
OP
Boss Hugg

Boss Hugg

Contributor
Bronco Guru
Joined
Jun 8, 2010
Messages
2,213
Jacob builds the case, shifter and shafts, you supply planetary set.

It still requires the adapter on the transmission. I've done lots of measuring myself to try to build one that takes place of the adapter. However, it would require a new short transmission output shaft similar to the one you get with the 4r70w/d20 adapter from advance adapters. Also, the output shaft bushing boss sticks out so far past the end of the case that it doesn't save enough length to make it pay off.




Sent from my iPhone using Tapatalk
 

Scoop

Contributor
Bronco Old Fart
Joined
Feb 1, 2006
Messages
11,122
Loc.
Cuchara, CO
I have the Blackbox i with the short AA adapter and it adds 3/4" to the drive train. But you have to go with a manual valve body.
 

68rockcrawler

Bronco Guru
Joined
Sep 18, 2006
Messages
1,417
I have the Blackbox i with the short AA adapter and it adds 3/4" to the drive train. But you have to go with a manual valve body.
Which transmission do you have? Is that the same adapter that would adapt your transmission right to your tcase, or just like a ring with bolt holes?

Sent from my XT1254 using Tapatalk
 

garberz

Bronco Influencer
Joined
Jun 24, 2007
Messages
6,864
Loc.
Conejo Valley, Ca.
It's a great idea, been done a few different ways before. Just don't expect a Dana 20 to hold up behind it for very long.

Mark
 

sykanr0ng

Bronco Guru
Joined
Aug 11, 2014
Messages
5,363
One of the things that would keep me from ever buying from him is that he starts the warranty when you buy it not when you get it or even when he ships it.
All the months while you are waiting for him to make it and send it to you are on the clock for your warranty.
 

Scoop

Contributor
Bronco Old Fart
Joined
Feb 1, 2006
Messages
11,122
Loc.
Cuchara, CO
Which transmission do you have? Is that the same adapter that would adapt your transmission right to your tcase, or just like a ring with bolt holes?

Sent from my XT1254 using Tapatalk

Drew, I've got a C4. It sorta looks like a big yo-yo with bolt holes on both sides!
 

68rockcrawler

Bronco Guru
Joined
Sep 18, 2006
Messages
1,417
It's a great idea, been done a few different ways before. Just don't expect a Dana 20 to hold up behind it for very long.

Mark
Yeah I've heard of guys splitting Dana 20s in half. Np205 seems like the best way to go.

Sent from my XT1254 using Tapatalk
 

ScanmanSteven

Bronco Guru
Joined
Dec 19, 2010
Messages
1,129
If you're worried about the warranty on the Behemoth I wouldn't worry about that too much as by design it's virtually indestructible. The ones of us that have them beat the snot out of our rigs and never worry about the doubler. But totally agree that a 205 needs to be behind it. D20 output shafts are prone to breakage, that's what caused my change. Even the Atlas has experienced breakage, NP205 breakage is rare.
 
Top