• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

full width questions

JGO

Contributor
Sr. Member
Joined
May 22, 2013
Messages
783
Hi all,

Has anyone done full width with cast wedge HP44? I recently bought a project with this axle and I want to finish cheap. After I relocate spring buckets I will have 4.5" of lift. Will 7 degree C bushings get my caster to a reasonable level? Also what steering are you guys using? I have enough parts to do Chevy tie rod over. Will that work without rubbing on a 15in rim? and what kind or track bar/track bar mounts are you guys running? Any pictures out there?

Thanks, Jim
 

WILDHORSES

Sponsor/Vendor
Bronco Guru
Joined
Nov 7, 2003
Messages
2,253
Loc.
USA
You should be in the neighborhood with the 7 degree. Ultimately the only way to know for sure is to check it when installed.

WH sells a trac bar riser for the 78-79 Bronco-F150 D44 that a lot of people are using with this swap. Usually you will need a custom length trac bar. You have to measure after the install and then deal with the trac bar. It's all custom so just about everyone doing a swap does it a little different.

https://www.wildhorses4x4.com/product/Trac-Bar-Riser-78-79-Bronco/Suspension_Parts_78yr

Jim
 

Attachments

  • 13494_8572_popup.jpg
    13494_8572_popup.jpg
    31.8 KB · Views: 36

Digger556

Sr. Member
Joined
Aug 8, 2013
Messages
801
Hi all,

Has anyone done full width with cast wedge HP44? I recently bought a project with this axle and I want to finish cheap. After I relocate spring buckets I will have 4.5" of lift. Will 7 degree C bushings get my caster to a reasonable level? Also what steering are you guys using? I have enough parts to do Chevy tie rod over. Will that work without rubbing on a 15in rim? and what kind or track bar/track bar mounts are you guys running? Any pictures out there?

Thanks, Jim

Yes, did it without modifying the axle itself, with the exception of adding a trackbar riser to improve suspension geometry.

The HP44 with cast wedges is 6" wider than the stock EB axle. All 6 inches are in the long side tube, so when centered, the diff is 3" further to the driver's side of the vehicle.

You will have to deal with the springs being 3" outboard on both sides. I did this by moving the upper spring buckets outboard 2" each and redrilling the lower spring buckets 1" inboard. 7° bushings will be a must for 4.5" of lift unless you a using radius arm drop brackets or aftermarket radius arms. I'm using homemade extended radius arms with no caster correction and the mounts directly under the frame with 3.5" of lift. Caster is measuring 4.5° right now.

Steering and trackbar will be custom. It is a good time to go tie-rod-over by re-reaming the knuckles. I'm used EB drum knuckles with Chevy brakes and had zero clearance issues with 15x8 rims with 3.5" back spacing. I now have 17x9 rims with 4.5" backspacing and no issues.

I got mine installed cheap with Chevy TREs, but I do a lot of fab myself.
 

68ford

Bronco Guru
Joined
Dec 26, 2004
Messages
2,710
Not sure on caster question being I made my own radius arms and did not use c bushing. Highly recommend doing that, but you may already have arms. As far as wheel clearance, if you run a average backspace 8in wide wheel there is no issues. I run 7/8 heims and have plenty of room. Also I highly recommend utilizing the additional width and room from inner edge of the tire to the frame and make your own track bar bracket that not only goes down, but outward towards the tire to be able to run the longest tracbar avail. You can build is easily to be strong and not need a riser. Then you do not have to limit your up travel because the riser hits the frame.
 
OP
OP
J

JGO

Contributor
Sr. Member
Joined
May 22, 2013
Messages
783
You should be in the neighborhood with the 7 degree. Ultimately the only way to know for sure is to check it when installed.

WH sells a trac bar riser for the 78-79 Bronco-F150 D44 that a lot of people are using with this swap. Usually you will need a custom length trac bar. You have to measure after the install and then deal with the trac bar. It's all custom so just about everyone doing a swap does it a little different.

https://www.wildhorses4x4.com/product/Trac-Bar-Riser-78-79-Bronco/Suspension_Parts_78yr

Jim
Thanks, Order coming!
 
Top