• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Tail Light pigtail replacement

jckkys

Contributor
Bronco Guru
Joined
Mar 15, 2012
Messages
5,221
I need to replace the tail light pigtail in the bucket. WH sells the pigtail but I don't see how it or the original are secured to the bucket. They are apparently inserted from the rear but are neither screwed in nor snapped in. Perhaps they are soldered. any insight would be helpful.
 

Pa PITT

Contributor
Bronco Guru
Joined
Jul 15, 2005
Messages
11,300
Loc.
Stephenville TEXAS
If they are like most old ''stuff''.. quality description there, but that's about it .
OLD TRAILER & Rear truck replacement lights. They are just 2 wires & a small circle of some fiber type material. You just simple cut your others off & Pushed the new pig tail through the tail light & Then put your new 1157 bulb in on top & give it a twist . Solder you 2 wires & you should have lights.
I'll say you should check & see if you've got the the correct wire hooked together .
...........
..... I'm going to say just go by your local NAPA store any good auto parts store should have the replacement pic tails. I sold them at my Parts Plus Parts Store.
... Also if your bronco has an aftermarket wiring harness It may come to the rear lamp with a 2 prong connector . Std Ign no. TC23 OR ALSO CALLED a 2 prong trailer connector . In my opinion this make it easier to replace next time .
But none of these items cost $5.00. Parts stores should still have new replacement red lens.
 
OP
OP
J

jckkys

Contributor
Bronco Guru
Joined
Mar 15, 2012
Messages
5,221
These are "new" 1968 buckets that Ford made out of stamped steel. With the pigtail inserted from the rear just pushing the bulb in the front pushes the pigtail out. If it's soldered heat would work. If it's spot welded I'm going to have to cut, drill, or grind it out. Trailer buckets are plastic so not much would apply to EB tail light buckets.
 

1970 Palmer

Sr. Member
Joined
Mar 2, 2020
Messages
454
If they are like most old ''stuff''..
But none of these items cost $5.00.

All of us old guys remember when this small stuff was "less than $5 bucks". LOL

But today, nothing costs less than $5 bucks. Just look at what happened to the price of small bulbs. They used to be 50 cents each, but now your forced to buy a package of two for $6 bucks. Check out the price of new wiper blades lately? Remember the days of buying just wiper blade inserts?

John
 

1970 Palmer

Sr. Member
Joined
Mar 2, 2020
Messages
454
These are "new" 1968 buckets that Ford made out of stamped steel. With the pigtail inserted from the rear just pushing the bulb in the front pushes the pigtail out. If it's soldered heat would work. If it's spot welded I'm going to have to cut, drill, or grind it out. Trailer buckets are plastic so not much would apply to EB tail light buckets.

I bet you could find some of the 1157 dual filament "snap in" sockets on the HELP rack at your auto parts store. Just measure your hole size and bring a caliper with you to compare the spring snap in diameter of the replacement.

I recently had my 1970 lights apart and cannot remember the type of pig tail. sorry.

John
 

EPB72

Contributor
Bronco Guru
Joined
Jul 13, 2019
Messages
1,216
Loc.
Pleasant Hill, CA
When I repaired my original ,the contacts where poor and a couple of the springs were rusted and collapsed,,,I found the bare contacts {in pics}.So I cut off the contacts from the wire tips ,theres a spring under the contact then the plastic block that keeps the contact in alignment ,,the wire pulls out the back side ..Cleaned everything up reassembled and crimped on the new contact..works great and still looks original,Wires were in good shape
 

Attachments

  • WIN_20200811_21_36_39_Pro.jpg
    WIN_20200811_21_36_39_Pro.jpg
    50.9 KB · Views: 107
  • WIN_20200811_21_37_04_Pro.jpg
    WIN_20200811_21_37_04_Pro.jpg
    52.6 KB · Views: 87

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
In my opinion the entire replacement tail lamp housing is the best way to go.
It's more expensive, but I've not had great luck trying to anchor the new sockets with pigtails to the old housings.
I know some have done it successfully, but mine were a mess. I think it would have been easier to glue them in with silicone, but then you don't get the ground bond with the reflector/housing.

And the bucket assembly has the correct wire colors (not a deal breaker) and the original style plug (again, not a deal breaker, but very nice!) to keep a more stock look and function.

I like to replace mine with Weatherpacks anyway, so keeping the original connector is low on my list of cool things, but it's high on my list of "man, that was easy" things.

Paul
 
OP
OP
J

jckkys

Contributor
Bronco Guru
Joined
Mar 15, 2012
Messages
5,221
I'm going with Paul's solution. After pulling the rubber off I can see the pigtail is at least welded in and removing it would mangle the bucket and the pigtail that includes the light socket. Even tho I can't see a spot weld, I don't see solder or brazing either. Some things aren't worth it.
 

Pa PITT

Contributor
Bronco Guru
Joined
Jul 15, 2005
Messages
11,300
Loc.
Stephenville TEXAS
1970 PALMER .. YOUR SO RIGHT ... I BOUGHT A Set of wipers about a month ago for this 2007 Ford Excape . I bought this thing to turn over after fixing the trans ..& I've got a Grand Son who will get his D/L in Sept or OCT.. & I WAS thinking he could use this as his 1st ride.
But his dad is going o buy him a cheaper ride.
... But I bought 28.00 wipers for this thing when I got it ...
they suck. I'M Thinking about going back & asking if I can trade them in & get some other brand . I replace a lot of wipers defective when I had my parts store.
 
Top