• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Where to start on body

Lando375

Jr. Member
Joined
May 23, 2020
Messages
118
Like the title says where do I start? The body on my EB is in pretty bad shape in all the right areas. I thought about just purchasing a new body but I’m a gluten for punishment. The floor and kick panels are the worst part. I plan on getting a complete floor platform and new kick panels. The doors posts are okay except for the lower portion under the rocker (both sides), that’s all rusted. I may replace those too. The inner fender aprons have rust in the usual spots but I think I can scab some sheet metal in. The rockers may be salvageable but both door strikers look like they were replaced at some time and may need to go. Last but not least. I’d like to replace both bed sides due to the cut fenders and welded on taillight housing. The PO welded the seam up all the way down the quarters.

So here’s my plan. Take a many measurements as possible. Install new body mounts. Brace the body up. Now is where I’m stuck. I’ve read start from front to back and I’ve read start from back to front.

Can I just cut the floor out and get the new one in and then do the kick panels one at a time? Also, is it possible to leave the door post in place when cut it free from the kick panel and slide a new kick panel in behind it? The door posts are the most intimidating part of this whole thing. What would you all do? Thanks for the advice!
 

AC932

Full Member
Joined
Sep 17, 2018
Messages
254
I, for no good reason, did kick panels, then floors, then door posts, then rockers, then bed.

I don't think you can slide a new kick panel behind the door posts, because (I think, its been a while) the door posts only attach to the kick panels.

I'd just start somewhere and work at it. No matter where ya start, there's gonna be times where it feels like it woulda been a whole lot easier if you'd started on the other side. As long as you're taking measurements and thinking everything through, you'll be fine (and have an easier time than me)
 

gmduncan

Sr. Member
Joined
Apr 30, 2019
Messages
388
Loc.
Annapolis
If it needs more than 50% of the sheet metal replaced, it may not be worth investing time and money. I'm not saying it's impossible to fix.

The amount spent for new sheet metal added to the hours of body shop or your labor, you might be close to the price of a new tub.

I'm in the same position you are... I've already done some simple math and at least for me, it's worth the money spent on a new tub.

Good luck and post some pictures.
 

Me2carcrazy1

Contributor
Jr. Member
Joined
Jan 11, 2019
Messages
130
Hmm, I recommend you eat a box of Wheaties for the job ahead of you since you are a "gluten" for punishment. Lots of gluten there to prepare you for your "glutton of punishment". LOL
Seriously, I agree with the others. Lay out a plan ahead of time of all the labor and parts you will need, add 20% cost for all the unexpected issues you will discover as you progress, and compare it to possibly buying a new tub. Finally, just pick a spot and start one small project at a time. I have already blown my budget, taken twice as long as I thought, still have a long ways to go but having a lot of fun doing it!
 
OP
OP
Lando375

Lando375

Jr. Member
Joined
May 23, 2020
Messages
118
Thanks guys. I did the math and it looks like for around $4k I can get all the parts I need to replace what I need to. The biggest costs is the complete floor pan and new flared quarters. Everything else seems to just add up. I'll be doing all the work myself so it would just be a labor of love and my time. I've never done this type of work before but I can cut and weld. I looked at NE Bronco's complete tub online and for the price, its really tempting. As much as I want to just purchase a new body, I want to see if I can do this. I've always done the mechanical work around cars but never the body. I guess we'll see.
 

Rustytruck

Bronco Guru
Joined
Feb 24, 2002
Messages
10,872
well its going to be a steep fast learning curve. buy the whole factory type rockers if you replacing rockers. try to keep your factory rear corners if you can. square and brace your rear tub with the tailgate on the rear tub tends to spread as the truck ages. make sure you keep the bed level front to back and side to side. Have fun no more vacations and holidays for you.
 
OP
OP
Lando375

Lando375

Jr. Member
Joined
May 23, 2020
Messages
118
well its going to be a steep fast learning curve. buy the whole factory type rockers if you replacing rockers. try to keep your factory rear corners if you can. square and brace your rear tub with the tailgate on the rear tub tends to spread as the truck ages. make sure you keep the bed level front to back and side to side. Have fun no more vacations and holidays for you.

HAHAHA Thanks for the tips!
 
OP
OP
Lando375

Lando375

Jr. Member
Joined
May 23, 2020
Messages
118
watch Stacey David do it on crazy horse. it may give you some ideas. all I know is it was beyond my ability so I bought a new body. good luck.

https://www.youtube.com/watch?v=DC6...aign=Full+Build:+1966+Ford+Bronco+Crazy+Horse

I actually watched watched the crazy horse episodes. I also found your build last week and sat down and binge read it start to finish. I'm highly impressed with your build. The crazy thing is I showed a co-worker your Bronco this morning.
 

ngsd

Contributor
Bronco Guru
Joined
Mar 2, 2019
Messages
2,702
Thanks guys. I did the math and it looks like for around $4k I can get all the parts I need to replace what I need to. The biggest costs is the complete floor pan and new flared quarters. Everything else seems to just add up. I'll be doing all the work myself so it would just be a labor of love and my time. I've never done this type of work before but I can cut and weld. I looked at NE Bronco's complete tub online and for the price, its really tempting. As much as I want to just purchase a new body, I want to see if I can do this. I've always done the mechanical work around cars but never the body. I guess we'll see.

It is hard to trealize it now but the amount of shop supplies, tools and additional work in final body prep will add significantly to that amount. Not saying to not do it, just prepare yourelf for the adds you cant anticipate until you have done this at least once.
 

Jamie Chriss

Sr. Member
Joined
Feb 28, 2015
Messages
577
I built my own tube after trying to salvage the one I had. If I could do it all over I would have purchased a new tub with no reservations. The new metal coming from the various vendors is suspect at best. Sure if you are replacing one or two panels, but every part is off enough when you finish you won't be happy.
 

ngsd

Contributor
Bronco Guru
Joined
Mar 2, 2019
Messages
2,702
I built my own tube after trying to salvage the one I had. If I could do it all over I would have purchased a new tub with no reservations. The new metal coming from the various vendors is suspect at best. Sure if you are replacing one or two panels, but every part is off enough when you finish you won't be happy.

Agreed, I spent months reading on this forum and no matter what, it still cant prepare you for what you are in for. The frustration about panel fit has been talked about a thousand times and you still get irratated when you get it in place and have to do surgery, bending and forcing to make them work. I really enjoyed it as well as hated it but in the end i learned a lot. And just like you, I learned I will either buy a rust free tub or get a new one next time!
 

Revelation

Bronco Guru
Joined
Oct 9, 2004
Messages
4,825
Mine was a blast to do, Was happy for the experience, We took out all bad metal before we started putting any new panels back in, replaced door posts, Rockers, and everything in front of the dash, even made the body stiffener that runs across in front of the seats To make things even more in depth all floors, firewall, bed cross braces, inner fenders and core support were all fabricated from 16 ga. stainless.
First-Day-Home2-Medium-1-1.webp
 

mustanggarage

Contributor
Sr. Member
Joined
Aug 14, 2018
Messages
647
I actually watched watched the crazy horse episodes. I also found your build last week and sat down and binge read it start to finish. I'm highly impressed with your build. The crazy thing is I showed a co-worker your Bronco this morning.

thanks. glad someone actually read it lol. btw I drove it for the first time tonight. so pretty pumped about that. it is worth it in the end. before I drive it much more it needs an alignment. I think I did a pretty good job with my tape measure and string but you know how it is lol. good luck with your project. post up a build thread when you get started.
 
Top