• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Lowest lift needed for 35's

73azbronco

Contributor
Bronco Guru
Joined
Nov 11, 2007
Messages
8,782
I searched, cannot find that answer. what the heck, my search skills are horrible. I have 35'S, 3.5sl, 2 inch bl. cut fenders.

Thinking out loud, I will never need that amount of lift, built this way because it was going to crawl, that never did nor will happen now. Hate to say it, it's about 2 inches to high for my butt, and my butt is not getting younger.

Considering loosing all SL, return to stock height SL springs, keep the 2 inch BL. Maybe use 1 inch coil pucks and 1 inch leaf spring block.

Will zero lift, 2 inch BL with cut fenders allow me to use 35's, knowing I'm not going to be flexing it?

This is a "thinking about in years" project, if at all. Heck I am just getting my 7 deg bushes next week.
 

Scoop

Contributor
Bronco Old Fart
Joined
Feb 1, 2006
Messages
11,122
Loc.
Cuchara, CO
I think I'd reduce the BL to 1 inch, cut 1 coil off both of your front springs and remove a leaf or 2 from your leaf packs. That should get you about a 2 inch drop.

I prefer a combo of SL and BL to get the lift you want. No SL and 2 inch BL is not the way to go IMO. Plus the addition of coil spring pucks and leaf blocks is just a sloppy way to get lift back. Plus the blocks could induce axle wrap. What I suggest above is a much neater and cleaner solution. And probably less costly.

This will probably still allow you to run 35s but will depend on how high your fender cuts are.
 

JeepGuy

Contributor
Bronco Guru
Joined
Aug 24, 2006
Messages
1,521
Body lift install isn't too expensive. I'd drop that 2" BL down to 1", or stock unless you really need to get between the body and frame rails. That is probably your cheapest route.
 

spap

Bronco Guru
Joined
Jan 2, 2010
Messages
2,642
I run a 3.5 SL and a 1 bl with 35s that is pretty much the norm and why I did it
I could easily run a 2.5 SL keeping the 1 bl and would have plenty of clearance however my front and rear fenders are cut. I agree with the others to reduce the body lift to one inch
 

Cortez

Bronco Guru
Joined
Jan 29, 2009
Messages
1,205
I see two easy options for you. BTW I also run a 3.5SL and 1”BL. You could easily reduce your BL to a 1” or eliminate it altogether and go strictly with a 3.5” SL but you may have to trim a little mor on the fenders...some guys will cut the fenders up to the body line. My preference is 3.5” SL and 1” BL
 

Attachments

  • 3B15865B-0EEF-4AEB-8DAC-F188F70727C1.jpg
    3B15865B-0EEF-4AEB-8DAC-F188F70727C1.jpg
    172.4 KB · Views: 228

Yeller

Contributor
Bronco Guru
Joined
Mar 27, 2012
Messages
7,692
Loc.
Rogers County Oklahoma
I’ve done one with 1” body lift, new stock 11 leaf springs and 1-1/2” coils from Wild Horses. It was really nice and with cut fenders had plenty of room. That was a street truck, I’ve been wanting to do a crawler with the same set up but haven’t gotten any takers, it will work better than a 3-1/2” with 2” body lift, lower is better
 

rguest3

Bronco Guru
Joined
Dec 13, 2012
Messages
3,780
73az - I would assume from your signature you still have the NV4500. If so, and for floor boards sake, then I would go to the 1" Body lift and a 2 1/2" SL. New Coils up front and drop a leaf from the rear. (which ever one is recommended)

The 7* Bushings should still be fine. You can keep the Drop Pitman Arm and Drop Trac Bar Bracket installed as well.
 

AZ73

Bronco Guru
Joined
Mar 28, 2012
Messages
3,813
I have 2.5 SL and 1 BL. I would easily get away with 1 SL and 1 BL.
 
OP
OP
73azbronco

73azbronco

Contributor
Bronco Guru
Joined
Nov 11, 2007
Messages
8,782
Thanks all.

Really want to avoid BL change, nv4500 has about 1 inch body clearance, if I drop I'd need to cut more off the hump.

so, all things equal, consensus is 2.5-3.5 total lift is what you need cut for 35's, non rock crawling.
 
OP
OP
73azbronco

73azbronco

Contributor
Bronco Guru
Joined
Nov 11, 2007
Messages
8,782
73az - I would assume from your signature you still have the NV4500. If so, and for floor boards sake, then I would go to the 1" Body lift and a 2 1/2" SL. New Coils up front and drop a leaf from the rear. (which ever one is recommended)

The 7* Bushings should still be fine. You can keep the Drop Pitman Arm and Drop Trac Bar Bracket installed as well.

I have raised arm, can you keep a raised arm with stock lift?
 
OP
OP
73azbronco

73azbronco

Contributor
Bronco Guru
Joined
Nov 11, 2007
Messages
8,782
last problem, I have shock hoops with almost no clearance, so BL needs to stay
 

sprdv1

Contributor
REBEL
Joined
Mar 8, 2007
Messages
81,996
I’ve done one with 1” body lift, new stock 11 leaf springs and 1-1/2” coils from Wild Horses. It was really nice and with cut fenders had plenty of room. That was a street truck, I’ve been wanting to do a crawler with the same set up but haven’t gotten any takers, it will work better than a 3-1/2” with 2” body lift, lower is better

being new would be nice too....
 
OP
OP
73azbronco

73azbronco

Contributor
Bronco Guru
Joined
Nov 11, 2007
Messages
8,782
Next question, oil pan clearance, I use a Weiand 2 sump 7 qt. Without getting under the truck, will that fit with stock lift? I think it mimics the EB stock hump, and is lower on back hump.

Duff has 1.5 progressive springs, looking at those. That would lop 2 off easy.

Back springs are currently 3.5 lift 11 pack from WH. Is it doable to remove leafs to get it to drop enough, or should I go down to 2.5 remove a leaf or just go Duff 1.5?

Again, not doing this this year, this is a going project.
 

Broncobowsher

Contributor
Total hack
Joined
Jun 4, 2002
Messages
37,112
The best thing you can do in the front is to put the frame on jackstands and take out the front springs. Jack the axle up. See what hits and what clears. Takes care of all the details specific to your ride.

Too bad the rear isn't as easy.
 

toddz69

Sponsor/Vendor
Bronco Guru
Joined
Nov 28, 2001
Messages
11,222
Next question, oil pan clearance, I use a Weiand 2 sump 7 qt. Without getting under the truck, will that fit with stock lift? I think it mimics the EB stock hump, and is lower on back hump.

Duff has 1.5 progressive springs, looking at those. That would lop 2 off easy.

Back springs are currently 3.5 lift 11 pack from WH. Is it doable to remove leafs to get it to drop enough, or should I go down to 2.5 remove a leaf or just go Duff 1.5?

Again, not doing this this year, this is a going project.

I wasn't able to find Duff's 1.5" springs on their website. Do you know if they're available and just not shown?

Thanks,
Todd Z.
 
OP
OP
73azbronco

73azbronco

Contributor
Bronco Guru
Joined
Nov 11, 2007
Messages
8,782
The best thing you can do in the front is to put the frame on jackstands and take out the front springs. Jack the axle up. See what hits and what clears. Takes care of all the details specific to your ride.

Too bad the rear isn't as easy.
Yeah, oh well sucks 15 years passed me by building this and my body fell apart more than this thing:)
 

rguest3

Bronco Guru
Joined
Dec 13, 2012
Messages
3,780
Going back to a lower 1.5" or stock height Suspension Lift would require stock Pitman Arm and delete Trac Bar Drop Bracket.
 
Top