• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Filler hole cut question

ngsd

Contributor
Bronco Guru
Joined
Mar 2, 2019
Messages
2,702
I am about to cut a hole for the gas filler in a perfect painted quarter. The body shop never cut it before paint. What would be the cleanest way to do this? Hole saws tend to walk and even with masking tape I am scared of messing this up. Anyone with suggestions other than normal carbide hole saws?
 

JWMcCrary

Contributor
Bronco Guru
Joined
Oct 14, 2004
Messages
5,001
Never done it but my thought would be to mark the hole and use a smaller hole saw to remain inside the opening needed. Then take a die grinder and work it to the correct size, but go slow, if the metal gets hot it might mess up the paint. obviously this should have been done before paint, but you are past that now. Good luck. I'm sure somebody has done this successfully.
 

1970 Palmer

Sr. Member
Joined
Mar 2, 2020
Messages
454
Greenlee knock out punch. If you have any electrician buddies, have them drop by for a beer, while you borrow the tool for five minutes. It's a pricy tool, but the best for the job.

John
 
OP
OP
ngsd

ngsd

Contributor
Bronco Guru
Joined
Mar 2, 2019
Messages
2,702
Greenlee knock out punch. If you have any electrician buddies, have them drop by for a beer, while you borrow the tool for five minutes. It's a pricy tool, but the best for the job.

John

I have used on bare metal but finished surfaces will leave marks i think.
 

BronCowie

Contributor
Old Timer
Joined
Apr 24, 2007
Messages
8,290
Loc.
Vancouver, WA
Greenlee knock out punch. If you have any electrician buddies, have them drop by for a beer, while you borrow the tool for five minutes. It's a pricy tool, but the best for the job.

John

These make a very clean cut. Maybe you can tape around the hole area and also on the outer cutting die edge to protect your paint. I used one on a stainless steel kitchen sink for a soap dispenser and it worked great. FYI, I've used these for years as an electrician for their intended purpose, they work flawlessly.
 

mustanggarage

Contributor
Sr. Member
Joined
Aug 14, 2018
Messages
647
I used one of these https://www.amazon.com/Tungsten-Car...B2Q,B01EIP2EWO,B099K1K33Y&srpt=SAW_BLADE&th=1 when I cut the hole in my dash to put my fuel pressure gauge in, after the dash was painted. I masked it and ran the drill on the low speed side and didn't push too hard and it worked perfect.
nOdiiBu.jpg
 

73azbronco

Contributor
Bronco Guru
Joined
Nov 11, 2007
Messages
8,782
My experience with the hole punches of that size from amazon and harbor freight, they don't like to penetrate thick american made sheet metal.
 

blubuckaroo

Grease Monkey
Joined
Jun 11, 2007
Messages
11,796
Loc.
Ridgefield WA
I'd use the correct size hole saw.
Make sure the mandrel and hole saw are tight, and the chuck is tight.
Make sure it's sharp, use slow speed, use very little pressure, and keep the saw square with the surface.
 
OP
OP
ngsd

ngsd

Contributor
Bronco Guru
Joined
Mar 2, 2019
Messages
2,702

Broncobowsher

Contributor
Total hack
Joined
Jun 4, 2002
Messages
37,112
If that doesn't work...
Try a unibit to make a starter hole and a body saw with a fine blade to trim to size.
And a half dozen layers of masking tape to protect the surrounding area.

Have you asked the body shop to cut the hole and finish it out?
 
OP
OP
ngsd

ngsd

Contributor
Bronco Guru
Joined
Mar 2, 2019
Messages
2,702
If that doesn't work...
Try a unibit to make a starter hole and a body saw with a fine blade to trim to size.
And a half dozen layers of masking tape to protect the surrounding area.

Have you asked the body shop to cut the hole and finish it out?

All good suggestions. I think after I practice on a couple old panels it will tell me whether I should just take it to the body shop like you suggested. I also need to have some scratches taken out of the clear anyway so it might work out.

I may also need to ask you a couple more questions about the AOD as I decided to give it a try. I put in a new TV cable and shifter with the Sniper and will surely be looking for advice on how to adjust it since you are the expert here!
 

Broncobowsher

Contributor
Total hack
Joined
Jun 4, 2002
Messages
37,112
Not sure how well the sniper will play with the AOD. The Sniper throttle goes from zero to full power with almost no opening. The AOD looks at torque based on throttle position, not vacuum level as a C4 would do. It would be easy to burn up an AOD at light throttle driving. A progressive linkage kit should help with that, but you have to run computer controlled timing as the ported vacuum is on the secondary butterfly. Best bet would probably be to run the Quadrajet replacement version of the Sniper. That would solve a lot of the issues. You loose the built in pressure regulator, but could care less as it is easy to use the LS fuel filter with built in regulator.
 

Broncobowsher

Contributor
Total hack
Joined
Jun 4, 2002
Messages
37,112
That looks like it. The linkage is progressive, secondaries don't open until about 50% primary throttle. and it looks like the ported vacuum goes to a primary throttle bore.

I had the standard Sniper and had big drivability issues at first. No ater how gentle I was o the throttle it was snappy off the line. Sure it feels like it has power. But it is on or off, might as well be a light switch. Opening all 4 throttle bores at once didn't offer control. So I got the aftermarket progressive linkage kit (that is standard on the Quadrajet version) and that fixed drivability. Flat ground cruise as well. I could not hold a steady speed on a flat road, either slightly gaining speed or slightly loosing it at 6-7% throttle. With the progressive linkage I could hold speed at 15% throttle. I passed on the Quadrajet version because I didn't want to add a pressure regulator, before I learned how simple the LS fuel filter would have been.
 
OP
OP
ngsd

ngsd

Contributor
Bronco Guru
Joined
Mar 2, 2019
Messages
2,702
Thanks I appreciate that. Do you have any recommendations for a local shop that could tune this for me? I am really lost on this and have never done an AOD/Sniper. It does already have an Edelbrock external regulator on it that was put on before the sniper purchase. I used the sniper on my crate blueprint and it was pretty much plug and play with a little tweaking but that was an AX15.
 

Broncobowsher

Contributor
Total hack
Joined
Jun 4, 2002
Messages
37,112
I don't have a recommended shop. This work I do myself at home, which I can't do now as I am about to have knee surgery.
 
OP
OP
ngsd

ngsd

Contributor
Bronco Guru
Joined
Mar 2, 2019
Messages
2,702
I don't have a recommended shop. This work I do myself at home, which I can't do now as I am about to have knee surgery.

Ok thanks I appreciate the help. Good luck with that surgery.
 

Rustytruck

Bronco Guru
Joined
Feb 24, 2002
Messages
10,872
I used a standard Bi-metal hole saw. mark your location and drill a 1/4" hole now take your hole saw and take out the drill bit and replace it with a 1/4 Inch rod. the rod will guide the hole saw and not dig out the center hole. masking tape the area and spray wd-40 as You should paint the edge of the hole to keep rust from creeping in from the edge of the cut.u saw through. then deburr the hole and remove the tape. clean the surrounding area.
 
OP
OP
ngsd

ngsd

Contributor
Bronco Guru
Joined
Mar 2, 2019
Messages
2,702
That is a good idea to change out the bit so it doesn't continue to walk out. Thanks
 
Top