• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Hood front adjustment at Grill

Torkman66

Contributor
Sr. Member
Joined
Apr 3, 2022
Messages
854
Loc.
New Braunfels, Tx
New hood, fenders, and grill. everything lines up very nice after a day of tweaks, bends, twists, and some light dolly work. Lines down hood and fenders are 5/16" on both sides and parallel. Hood arch matches fender arches. Grill mates up to fenders very nice. Rear of fenders have nice 1/4" line with doors (after much gnashing of teeth and some slight metal mod).

However, the hood is about 1/4" short. (see pics). It is about 3/16" short on the drivers side and 1/4" short on the passenger side because I used a single shim on the drivers side hinge to square up the lines with the fenders. So I know I can shim the hinges more to get the hood to match the grill tip, but how much shim is too much? I will need approximtley 1/4" shim on both sides to get the hood to match the grill. That will make a 1/4" + gap on back of hood at the windshield/cowl area. Is that OK or are there other options to consider?

IMG_6556.JPG IMG_6555.JPG
 

jamesroney

Contributor
Bronco Guru
Joined
Sep 11, 2007
Messages
2,607
Loc.
Fremont, CA
Somebody’s door gaps are too big.

Take a straight edge and show me where your fender is located in relation to your windshield hinge center.

Zero shims is the correct number. But 1/16 on one side or the other to square it up is OK.

I’ll post some pics tomorrow of mine.
 
Last edited:
OP
OP
Torkman66

Torkman66

Contributor
Sr. Member
Joined
Apr 3, 2022
Messages
854
Loc.
New Braunfels, Tx
I’ll snap some pics where fender meets windshield. FYI, door gaps ar 3/16” with quarters, 1/4” at fender. Holes all line up fender to post and fender to apron. No space to move fenders back without door gaps going to zero. All original pillars. Only change was rockers which went on after doors installed and gaped.
Frustrating!!
8D994173-180A-46BC-AB49-EF88CD6E3D86.jpeg 91E6290F-050A-49C4-859A-C52E331480CE.jpeg B57CDE28-4BC2-4574-9DA8-F9411A7DE33E.jpeg E703F48F-EAF4-4CB4-B7DE-B1EECA54F7D8.jpeg 7CD6701E-A550-4A5D-86DE-6A3AB556FBBE.jpeg 52367283-D6CC-488E-9A61-80BB417FC8AF.jpeg
 
Last edited:

bronkenn

Contributor
Bronco Guy
Joined
Apr 27, 2017
Messages
2,717
Loc.
Southeast Ohio
I am not agin bending hinges a little when needed. That is how it was done in the factory body shop at the Truck and Bus plant back in the 70's and 80;s.
 
OP
OP
Torkman66

Torkman66

Contributor
Sr. Member
Joined
Apr 3, 2022
Messages
854
Loc.
New Braunfels, Tx
I agree, but if I bend door hinges to move doors back, that will make door to quarter gap near zero. It is 3/16 to 1/4 now.
 

jamesroney

Contributor
Bronco Guru
Joined
Sep 11, 2007
Messages
2,607
Loc.
Fremont, CA
I agree, but if I bend door hinges to move doors back, that will make door to quarter gap near zero. It is 3/16 to 1/4 now.

Do you want to restore your Bronco correctly, or do you want to put it back together the way the factory did it? It is two very distinct and unique answers...and it will have a profound impact on what you do next.
 

Attachments

  • FEA259FF-D78B-455D-8D0C-6268A189CDBE.jpeg
    FEA259FF-D78B-455D-8D0C-6268A189CDBE.jpeg
    201.5 KB · Views: 228
  • B1F6A8C5-5845-44C3-94F1-DBA755AC320B.jpeg
    B1F6A8C5-5845-44C3-94F1-DBA755AC320B.jpeg
    186.3 KB · Views: 215
  • 4F47CF1A-161E-4D8A-8481-B939B9A39B51.jpeg
    4F47CF1A-161E-4D8A-8481-B939B9A39B51.jpeg
    166.5 KB · Views: 214
  • A3F5C269-2E83-4B51-A330-400D32D4346C.jpeg
    A3F5C269-2E83-4B51-A330-400D32D4346C.jpeg
    120.2 KB · Views: 217
  • 8A480105-6D3E-46AE-8555-00DE29BD3E9E.jpeg
    8A480105-6D3E-46AE-8555-00DE29BD3E9E.jpeg
    169.9 KB · Views: 240
Last edited:
OP
OP
Torkman66

Torkman66

Contributor
Sr. Member
Joined
Apr 3, 2022
Messages
854
Loc.
New Braunfels, Tx
Thanks for the background and advice. I am a retired military guy with one hobby…restoring a car or truck. Normally one a year. This Bronco is one of many old cars I have done and each have their challenges. The lines are important to me. First thing I look at are the lines and gaps on a show car. I know the hours of work required to get it right.

However, I am also a realist. If making the Bronco right means removing unrusted pillars or nicely installed quarters to gain a 1/4” at hood, then I’ll not go that far. If I was at the stage where all of the tub was being built, I know now that the fit has implications from tailgate to hood tip. But I’m way past that and now have a rust free truck with all welding near complete.

So, that lands me in the not perfect but way better than factory catigory. From the pics I posted my fenders look right when measured at the windshield hinge. I’m thinking I might try to move the doors aft as much as I can stand, move fenders aft as much as I can stand, then see what’s left with the grill hood line and shim as needed. Short of that process, not sure I have any other options given my position outlined above.
 

jamesroney

Contributor
Bronco Guru
Joined
Sep 11, 2007
Messages
2,607
Loc.
Fremont, CA
Thanks for the background and advice. I am a retired military guy with one hobby…restoring a car or truck. Normally one a year. This Bronco is one of many old cars I have done and each have their challenges. The lines are important to me. First thing I look at are the lines and gaps on a show car. I know the hours of work required to get it right.

However, I am also a realist. If making the Bronco right means removing unrusted pillars or nicely installed quarters to gain a 1/4” at hood, then I’ll not go that far. If I was at the stage where all of the tub was being built, I know now that the fit has implications from tailgate to hood tip. But I’m way past that and now have a rust free truck with all welding near complete.

So, that lands me in the not perfect but way better than factory catigory. From the pics I posted my fenders look right when measured at the windshield hinge. I’m thinking I might try to move the doors aft as much as I can stand, move fenders aft as much as I can stand, then see what’s left with the grill hood line and shim as needed. Short of that process, not sure I have any other options given my position outlined above.
Don't forget that the hood gets a little longer if you lower it in the back. And you can cheat a little on the hood hinges by bending instead of shimming.

I am also retired, and my hobby is car restoration. One a year was my target as well. (great minds...) I'm 100% in agreement with your assessment. Which is why I ended up shaving one door, and re-forming one fender at the A-pillar to get the front clip SQUARE, and then cheating the hood hinges to get it FLUSH.

The White Bronco that you see in the pictures is also retired USAF. It is an original sheet metal 1967 U13 Military Bronco that is 100% rust free. You can see that one side of the Bronco is longer than the other side by about 3/16. And it all shows up in the door gaps and at the hood. And no, I'm not going to un-weld good metal either.
 

jamesroney

Contributor
Bronco Guru
Joined
Sep 11, 2007
Messages
2,607
Loc.
Fremont, CA
Thanks for the background and advice. I am a retired military guy with one hobby…restoring a car or truck. Normally one a year. This Bronco is one of many old cars I have done and each have their challenges. The lines are important to me. First thing I look at are the lines and gaps on a show car. I know the hours of work required to get it right.

However, I am also a realist. If making the Bronco right means removing unrusted pillars or nicely installed quarters to gain a 1/4” at hood, then I’ll not go that far. If I was at the stage where all of the tub was being built, I know now that the fit has implications from tailgate to hood tip. But I’m way past that and now have a rust free truck with all welding near complete.

So, that lands me in the not perfect but way better than factory catigory. From the pics I posted my fenders look right when measured at the windshield hinge. I’m thinking I might try to move the doors aft as much as I can stand, move fenders aft as much as I can stand, then see what’s left with the grill hood line and shim as needed. Short of that process, not sure I have any other options given my position outlined above.
Don't forget that when the fender ends up "too long" that usually means that the door is too far forward. Which shows itself as the door gap ahead of the windshield pin. When that happens, the upper door frame at the TVW (Triangle Vent Window) will end up hitting the windshield frame when the top gets installed.

Yours might be fine, but I doubt it.

After you get done with your tantrum, and pick up all of the objects flying around your shop...The easiest way to fix it all is to shave the rear edge of the door by 1/8. Then porta-power the strike post about 1/16. Then pull the hinges rearward about 1/8. Then your door will fit properly in the opening, and the weatherstrip will actually fit.

Aren't you glad it isn't painted?
 
OP
OP
Torkman66

Torkman66

Contributor
Sr. Member
Joined
Apr 3, 2022
Messages
854
Loc.
New Braunfels, Tx
Nice!! I added 1/16” shims to door hinges which closed the gap with quarters to 1/8”. I moved the fenders back to a 1/8” gap and then added 1/16” shim to both hood hinges. The hood now mates right with the grill. Doors close nice with straight gap lines. 1/8” is a bit tight I think but maybe that’s not a problem???
Yes, I could go ahead and move doors to 1/16” gap which would put fenders at 3/16”. Shave rear door, bend piller back, could even get a 1/16” by cutting just behind quarter edge press together width of the cutoff wheel blade and spot weld.

Or, call it good. I have 1/8” hood shim in drivers hinge and 1/16” in passenger. 1/8” straight gaps front and rear of doors.
 

jamesroney

Contributor
Bronco Guru
Joined
Sep 11, 2007
Messages
2,607
Loc.
Fremont, CA
Nice!! I added 1/16” shims to door hinges which closed the gap with quarters to 1/8”. I moved the fenders back to a 1/8” gap and then added 1/16” shim to both hood hinges. The hood now mates right with the grill. Doors close nice with straight gap lines. 1/8” is a bit tight I think but maybe that’s not a problem???
Yes, I could go ahead and move doors to 1/16” gap which would put fenders at 3/16”. Shave rear door, bend piller back, could even get a 1/16” by cutting just behind quarter edge press together width of the cutoff wheel blade and spot weld.

Or, call it good. I have 1/8” hood shim in drivers hinge and 1/16” in passenger. 1/8” straight gaps front and rear of doors.
Is it a keeper, or a flip? You know that 1/8 is tight. But if both doors are tight like that, it's probably OK. If one is tight, and one is loose...then you have duplicated the factory look! But you will have to look at it every day, and every time you get in it. It might not bother you, but it would bug the crap out of me. And then I'd have to sell it. Eventually it w

Sleep on it, and look at it in the morning. Body work always looks worse in the AM. Always looks great when you quit for the day. The decide if you are building a show car, or a beater. Then fix it. (you can blame me.)
 
OP
OP
Torkman66

Torkman66

Contributor
Sr. Member
Joined
Apr 3, 2022
Messages
854
Loc.
New Braunfels, Tx
Man, you are in my head!! Yes, both sides are right at 1/8". All gaps are straight. This is intended as a keeper that I want to be show car quality. The gaps at the rear doors need to be 3/16" in my opinion to look right. Some say a paint stick is right, that is 0.125 which is exactly 1/8". But it just looks tight to me. I have no idea how the weather stripping is going to affect all of this. I've read hard to close posts. Wonder if the 1/8" gap will help or hurt closing with weatherstrip?

If I shave the rear of the door, I'll need to go past what I want a small bit in order for room to weld a tiny bead down the door edge to reseal the skin...is that how you would do it?
 

jamesroney

Contributor
Bronco Guru
Joined
Sep 11, 2007
Messages
2,607
Loc.
Fremont, CA
Man, you are in my head!! Yes, both sides are right at 1/8". All gaps are straight. This is intended as a keeper that I want to be show car quality. The gaps at the rear doors need to be 3/16" in my opinion to look right. Some say a paint stick is right, that is 0.125 which is exactly 1/8". But it just looks tight to me. I have no idea how the weather stripping is going to affect all of this. I've read hard to close posts. Wonder if the 1/8" gap will help or hurt closing with weatherstrip?

If I shave the rear of the door, I'll need to go past what I want a small bit in order for room to weld a tiny bead down the door edge to reseal the skin...is that how you would do it?
"Show car quality keeper." Nothing I say matters now. You know it, and I know it.
 

bronkenn

Contributor
Bronco Guy
Joined
Apr 27, 2017
Messages
2,717
Loc.
Southeast Ohio
I was wondering if you have your door strikers and latch are on? With a 1/8th inch gap it might interfere with the closing as contact with striker and door. I worked a while to get my door fits to look real nice only to have the seals rain on my parade.
 
OP
OP
Torkman66

Torkman66

Contributor
Sr. Member
Joined
Apr 3, 2022
Messages
854
Loc.
New Braunfels, Tx
Yes, they work great. Thanks for checking. The details overlooked are what creat the biggest problems!! Did you solve your weatherstripping issue?
 
OP
OP
Torkman66

Torkman66

Contributor
Sr. Member
Joined
Apr 3, 2022
Messages
854
Loc.
New Braunfels, Tx
Taking James’ inputs that the problem was with the fender placement which is a factor of the door placement, I moved everything back. Small 1/16” hood shim put hood exactly on grill tip.

1/8” gaps at fender and quarter I could just not leave. I shaved down 1/16” off the front of door and 1/16” off back of door. Had to weld the skin edges where the shaving broke through, then smoothed with flap pad. Now I have 3/16” top to bottom on fender and quarter gaps. 1/4” along rocker.

Tomorrow, second door.

Also, I wanted to mention that I know a lot of you use paint sticks and such for door gap checks. That’s ok in a pinch, but if you’re setting gaps and want them really close to say 3/16”, make a steel gap gauge. The one I made is a 3/16” with one end for checking gaps and the other is a scribe that sets a mark into adjoining gap edges that need to enlarge. The wooden sticks have flex and some degree of shrinkage over time. The metal gauge takes 10 minutes to make and is always accurate.
BEDBA003-EB19-4973-A14D-240F764E9621.jpeg EB7F0152-6FD0-405D-9E91-D8B9CC6B82B6.jpeg
 

bronkenn

Contributor
Bronco Guy
Joined
Apr 27, 2017
Messages
2,717
Loc.
Southeast Ohio
Yes, they work great. Thanks for checking. The details overlooked are what creat the biggest problems!! Did you solve your weatherstripping issue?
I did some trimming on mine and they work OK but the door fit isn't as good as before the seals. Good luck with yours.
 

Madgyver

Bronco Madman
Joined
Jul 30, 2001
Messages
15,030
I had similar issues and just tweaked the SS hood hinges a little. bend a little and or add shims.
 

BOBS 2 68S

Full Member
Joined
Jul 26, 2015
Messages
280
Loc.
Hudson, CO
OK. Not to hi-jack this, But my hood sits proud of the grill and fenders about 3/16 of a inch. No shims. The hood in not original to this tub.
 
Top