• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Help! 10x2.5" brake woes.

LoneRanger

Contributor
Sr. Member
Joined
Jun 13, 2007
Messages
577
Loc.
Gunshine State
Rebuilding a 66' 9" small bearing 10x2.5 drum setup.

Got new (to me) backing plates from Nick @ NorthEastFordParts.

Got a full 10x2.5" drum rebuild from Bronco Graveyard.

The shoes DO NOT fit on these backing plates. See photos. While the shoes measure 2.5" across they sit 1/4" (or more) high on the top post. You can see light underneath them.

I need part numbers for the correct shoes (from all the normal chain stores as I want to drive wherever it takes to get this stuff TOMORROW)

I did quick measurements with Nick (on the shop floor) when I called earlier but later I remeasured on a semi flat bench. The backing plate sits up on 2 bumps (one of which is for the ebrake cable) as well as the bleeder nipple on the brake cylinder.

I then remeasured with the cylinder loose and the 2 bumps hanging off the edge of the bench so it was flat and got a much different number.

Also I need 2 sets of the bake shoe links or wheel cylinder pins. I've heard them called both. Part numbers greatly appreciated.

See pics attached.

L.R.
 

Attachments

  • PXL_20231116_230816476.jpg
    PXL_20231116_230816476.jpg
    155.4 KB · Views: 103
  • PXL_20231116_230823177.jpg
    PXL_20231116_230823177.jpg
    173.1 KB · Views: 96
  • PXL_20231116_230901128.jpg
    PXL_20231116_230901128.jpg
    115.1 KB · Views: 92
  • PXL_20231116_230935272.jpg
    PXL_20231116_230935272.jpg
    137.4 KB · Views: 73
  • PXL_20231116_231102743.jpg
    PXL_20231116_231102743.jpg
    187.3 KB · Views: 111
  • PXL_20231116_231410825.jpg
    PXL_20231116_231410825.jpg
    124.9 KB · Views: 69
  • PXL_20231116_231523486.jpg
    PXL_20231116_231523486.jpg
    167 KB · Views: 103
  • PXL_20231116_231607497.jpg
    PXL_20231116_231607497.jpg
    224.7 KB · Views: 100
  • PXL_20231116_231707801.jpg
    PXL_20231116_231707801.jpg
    223.7 KB · Views: 89
  • PXL_20231116_230911735.jpg
    PXL_20231116_230911735.jpg
    201.4 KB · Views: 80

BROwN COw

Sr. Member
Joined
Dec 14, 2006
Messages
450
Rob, I have no idea on this, but I find that O’reily’s carries more EB specific stuff than others.
 

jamesroney

Contributor
Bronco Guru
Joined
Sep 11, 2007
Messages
2,607
Loc.
Fremont, CA
Are the backing plates for the 11 X 1-3/4" brakes?
Without being able to see this thing, I am going to guess that those are a set of back plates from a small bearing 9 inch, (or an 8 inch) from a passenger car (or E100 Van) that is looking for 10x2 shoes.

Tragically, the brake offset is the same for the 10x2 and the 10x2.5. So while the back plate sits deeper, the drum also sits deeper.

I had this exact same problem, (but backwards) when I was looking for back plates for my 67 Shelby GT500. They are supposed to be 10x2.5, but people often install a full set of 10x2 Mustang drums and back plates. It works fine on the Shelby, because you can get either 2 inch or 2.5 inch drums for the passenger car in 5x4.5 lug pattern.

But trying to put 2 inch wide shoes on a Bronco is going to be a challenge. Even if you find shoes to fit those back plates, (65-70 Mustang 10x2) the 2.5 drums will be too deep. You can prove this by putting the back plate on the axle, and trying to mount the drum. You will find that the drum hits the back plate by about 1/2 inch. Trying to find a set of 10x2 drums in 5x5.5 might be hard. A 1963-1973 CJ5, or Scout will probably do it. But the center hole will be wrong.

But it's silly. You really want to find a set of back plates from Bronco. Best of luck.
 

jeffncs

Contributor
Bronco Guru
Joined
May 4, 2004
Messages
1,898
Loc.
Raleigh, NC
I struck out everywhere finding 10” drums for my truck…. NAPA found some for me. I paid shipping and more, but she found them for me!
 

englewoodcowboy

Lick Creek Restorations
Joined
Jul 25, 2010
Messages
4,201
Rob by your last measurement I’m thinking those are 11” backing plates. If you have a 10” drum, set it on the plate to confirm, it should nestle in the lip.
 
OP
OP
LoneRanger

LoneRanger

Contributor
Sr. Member
Joined
Jun 13, 2007
Messages
577
Loc.
Gunshine State
The new raybestos drums I have sit perfectly on the plates (pn not currently available) but they came in the Bronco Graveyard 10" kit.

L.R.
 
OP
OP
LoneRanger

LoneRanger

Contributor
Sr. Member
Joined
Jun 13, 2007
Messages
577
Loc.
Gunshine State
See attached drum pics, PN and fitment.

Nick sent me a text last night and it's possible I got 10" mustang backing plates by mistake.

L.R.
 

Attachments

  • PXL_20231117_132135609.jpg
    PXL_20231117_132135609.jpg
    174.9 KB · Views: 97
  • PXL_20231117_132156522.jpg
    PXL_20231117_132156522.jpg
    191.7 KB · Views: 85
  • PXL_20231117_132205351.jpg
    PXL_20231117_132205351.jpg
    100.4 KB · Views: 92
Top