• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Shock Tower Placement

Okie69

Contributor
Sr. Member
Joined
Nov 28, 2011
Messages
842
How does this placement look to y’all? I’m using the bolt on kit from Duffs so I can easily switch to a taller tower later if I want. I wonder about leverage on the frame in this position.

Red marks to show where the four bolts would go.
085CFBA3-31F3-4AC3-B62E-E1B7DB7FBC55.jpeg
EC1D4B79-F909-4A89-A786-9814B97CC1AB.jpeg


I thought I was supposed to use these existing holes but I don’t think that’s gonna work 😳

FF3BBE66-9D72-4460-9B5B-7177559ECA9B.jpeg
24009486-EFD7-49D0-993B-56E7CFE0FB83.jpeg
 
OP
OP
Okie69

Okie69

Contributor
Sr. Member
Joined
Nov 28, 2011
Messages
842
Why would you go longer towers later and not now?
Why would you not go longer now and weld them in good and tight?

Valid point, but I’ve already got these so I’m just gonna give them a go. These are “long travel” towers from Duffs they’re just the 0-1” body lift variety.
 

Jamie Chriss

Sr. Member
Joined
Feb 28, 2015
Messages
577
I replaced min a few years back. if you were welding them on pic one looks good. If you are bolting them on the last pic, make sure it aligns with the spring perch.
Do you have any welding experience? Its ok to use the bolts, but is would weld the sides to the frame it were me. Also what does the instruction say about placement and do you need 6 bolts, I think that would just weaken the frame drilling all those holes.
 

Yeller

Contributor
Bronco Guru
Joined
Mar 27, 2012
Messages
7,692
Loc.
Rogers County Oklahoma
Valid point, but I’ve already got these so I’m just gonna give them a go. These are “long travel” towers from Duffs they’re just the 0-1” body lift variety.
I always find this interesting. I'm posting this for thought and discussion, not a debate or slander of anyone's thoughts, or set up, just sharing what I have experienced in a few decades of building and using stuff.

Your only going to get about 9" maybe 10" useable travel. Why do you need a 15" travel shock that you are using 50-60% of? just doesn't make since. Do what packages easy and gives you what you really need. A shock with 26" of extended length and a compressed length of 15" is easy to package and has more wheel travel then you will ever use, even 24" extended and 14" compressed is more than enough. Now if you do long arms you can get more to a point but there still only so much that is usable. People are always amazed that the shocks on my bronco are only 11" travel, it gets run like a desert racer and crawls with the best of them and I've been told performance wise it has been a lot of builders bench mark. Just something to think about.

FYI: your installation location looks good for what I can see in the pic.
 
OP
OP
Okie69

Okie69

Contributor
Sr. Member
Joined
Nov 28, 2011
Messages
842
Interesting questions to bring up. I don’t have answers. This is my first build and my first foray into trying to make something with a little more flex. I’m trying to make sure my shocks aren’t the limiting factor on the front end.

Once I get everything mounted up I’m going to figure out a way to flex it out and measure before ordering shocks.

Also, I wanted to get rid of the stud mount shocks so if nothing else I’ve got that handled. haha

With the 2.5” lift and 35s and T-Rex arms I assume I’ll be getting into the body before running out of travel.
 

Yeller

Contributor
Bronco Guru
Joined
Mar 27, 2012
Messages
7,692
Loc.
Rogers County Oklahoma
Yes with those towers, shock length will not be the limiting factor. That is as long as the installed shock isn't too long and limiting up travel.
 

Apogee

Contributor
Bronco Guru
Joined
Nov 26, 2005
Messages
6,348
Loc.
Tangent, OR
Just to add to what Yeller said, I'd be worried about bottoming out on the shock if it's too long. I'm mid-swap on a HPD44 and I'm putting the axle at full stuff (without springs), and then positioning my shock mounts based on the collapsed length of my shocks...with a little room to spare since I'd rather lose 1" of travel than blow out my shocks on a hard impact. This allows me to set the height of my bumpstops as well, so that it' bottoms out on those rather than the CAGE long-arms hitting the frame.
 

ngsd

Contributor
Bronco Guru
Joined
Mar 2, 2019
Messages
2,702
I have a set of those towers I won in a raffle if anyone needs some
 
OP
OP
Okie69

Okie69

Contributor
Sr. Member
Joined
Nov 28, 2011
Messages
842
So just as a follow up I got these mounted. If anyone is reading this at a later date I would steer clear of the bolt on option for this setup. It’s a hassle. Trying to drill through the frame and have the backing plate holes line up is no fun, and I had to go get shorter bolts to clear the starter on the passenger side.

I initially went with this because I don’t own a welder, but if I was going to do it again I would’ve just found somebody to weld them on. Or I would’ve went with f250 shock towers…
219A04E2-E9D4-4A01-BB43-F24EC5E975A4.jpeg
824B1E81-246A-4556-9C33-7885BCB03FF4.jpeg
 

U15FLG

New Member
Joined
Aug 25, 2022
Messages
12
So just as a follow up I got these mounted. If anyone is reading this at a later date I would steer clear of the bolt on option for this setup. It’s a hassle. Trying to drill through the frame and have the backing plate holes line up is no fun, and I had to go get shorter bolts to clear the starter on the passenger side.

I initially went with this because I don’t own a welder, but if I was going to do it again I would’ve just found somebody to weld them on. Or I would’ve went with f250 shock towers…
View attachment 883011 View attachment 883012
Really appreciate the pictures and experience, I m getting ready to install the same shock mounts. What engine trans are you running? How much clearance between the starter and the bolts/nuts/backing plate did you end up with after install?
 
OP
OP
Okie69

Okie69

Contributor
Sr. Member
Joined
Nov 28, 2011
Messages
842
It’s a 302 and stock 3 speed in these pics. There is very little clearance between the starter and the closest bolt on that side. It’s really not worth it in my opinion. Get them welded on and save yourself the hassle.
 

RODRIG3911

Contributor
Bronco Guru
Joined
Jul 9, 2007
Messages
1,019
Loc.
Tucson
So just as a follow up I got these mounted. If anyone is reading this at a later date I would steer clear of the bolt on option for this setup. It’s a hassle. Trying to drill through the frame and have the backing plate holes line up is no fun, and I had to go get shorter bolts to clear the starter on the passenger side.

I initially went with this because I don’t own a welder, but if I was going to do it again I would’ve just found somebody to weld them on. Or I would’ve went with f250 shock towers…
View attachment 883011 View attachment 883012
Hello Okie. I just wanted to tell you that you still can weld on those towers at a later date if you choose. Probably even better, because you can plug weld the bolt holes along with welding all around the outside. I have a very similar set up to you. F250 shock mounts, duff long arms and f150 knuckles. Works well =)
 

U15FLG

New Member
Joined
Aug 25, 2022
Messages
12
It’s a 302 and stock 3 speed in these pics. There is very little clearance between the starter and the closest bolt on that side. It’s really not worth it in my opinion. Get them welded on and save yourself the hassle.
Original plan was to weld...but mocking them up today I have them tight against the spring tower and don't see how I could get a weld gun tip in on those front facing edges. I m doing a coyote swap and sat the engine/trans in the frame for the first time yesterday to check starter clearance based on your post. I have the thickness of a tape measure between my inner frame rail and the starter solenoid (I have a clickable starter but it is rotated as much inward as possible currently) which is just barely enough for the backing plate and a nut (assuming I cut the excess bolt off). Unless I can find a solution on how to weld that front edge my plan is to use the marks I made for solenoid location and see if I can work around that area with my bolt placement. Open to ideas/suggestions. Also, are your shock towers straight up and down (parallel to the spring towers)?
 

Wild horse 75

Sr. Member
Joined
May 9, 2023
Messages
464
Loc.
BC
Original plan was to weld...but mocking them up today I have them tight against the spring tower and don't see how I could get a weld gun tip in on those front facing edges. I m doing a coyote swap and sat the engine/trans in the frame for the first time yesterday to check starter clearance based on your post. I have the thickness of a tape measure between my inner frame rail and the starter solenoid (I have a clickable starter but it is rotated as much inward as possible currently) which is just barely enough for the backing plate and a nut (assuming I cut the excess bolt off). Unless I can find a solution on how to weld that front edge my plan is to use the marks I made for solenoid location and see if I can work around that area with my bolt placement. Open to ideas/suggestions. Also, are your shock towers straight up and down (parallel to the spring towers)?
I wouldn’t worry about welding the front edge too much. You can probably slide them back a bit to gain clearance. But if you weld the top edge and the two side on the side of the frame plus plug welding all the bolt holes there will be plenty of weld to hold them. Shocks mounts shouldn’t be holding vehicle weight just shock pressure (unless you’re using coil overs). Proper bump stops should stop up travel before you put weight on the shocks. You could also add a brace from the top of the spring perch to help gusset it even more. Lots you can do to make up for not welding that front edge.
 

U15FLG

New Member
Joined
Aug 25, 2022
Messages
12
I wouldn’t worry about welding the front edge too much. You can probably slide them back a bit to gain clearance. But if you weld the top edge and the two side on the side of the frame plus plug welding all the bolt holes there will be plenty of weld to hold them. Shocks mounts shouldn’t be holding vehicle weight just shock pressure (unless you’re using coil overs). Proper bump stops should stop up travel before you put weight on the shocks. You could also add a brace from the top of the spring perch to help gusset it even more. Lots you can do to make up for not welding that front edge.
good points, are your shock towers straight up and down (parallel to the spring towers)?
 
OP
OP
Okie69

Okie69

Contributor
Sr. Member
Joined
Nov 28, 2011
Messages
842
good points, are your shock towers straight up and down (parallel to the spring towers)?
I’ll check mine when I get back around the house. I think they’re angled back slightly.
 
Top