• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Liftgate Latch pins fall out

Jaybr

Contributor
Sr. Member
Joined
Oct 8, 2019
Messages
587
I tried to install the liftgate latch a couple weeks ago and had a few issues:

When tightened down the latch bound up in the cut out on the lift gate. I filed that down and got it moving freely

Second problem was the flat ends of the rods wouldn’t fit in the slots on the latches. Again, filed them down and got them moving freely.

The last problem I have not resolved and could use some advice. The 1/8 pins don’t fit tight in the rods. When opening the hatch spring pressure is released from the pins and the move and eventually fall out. The pin under the spring I have to hammer in with a roll pin punch, the ones in the rod I can push in with my finger.

Is there something I can put on them to hold them in place (loctite?). Or should I take it back apart and drill the holes to 5/32 and use larger pins?


Sent from my iPhone using Tapatalk
 
OP
OP
Jaybr

Jaybr

Contributor
Sr. Member
Joined
Oct 8, 2019
Messages
587
97faa168d67435c1765da7084859c455.jpg


In closed position the spring pressure holds the pin fine

55cc0cdf69af46582f59545bc7e8d38a.jpg


In open position the pin falls out
18436fc0233746ae542629308403035d.jpg

Orientation of mechanism

The hole in the rod is too big for the 1/8 pins that came with it, too small for a 5/32 pins


Sent from my iPhone using Tapatalk
 

ntsqd

heratic car camper
Joined
Jan 30, 2005
Messages
5,970
Loc.
Upper SoKA
Looks like new parts, any chance of getting the vendor to make it right?

The auto trans column shifter in the Wagon has a similar problem, the roll pin pivot for the lever has wallowed-out the casting and it would easily slip out. My short term solution (until I get the floor shifter mounted) was to run a piece of Ø.032 safety wire thru the hole in the pin and wind the two ends tightly together with safety wire pliers. That might also work for you. the pins will still be able to move around, but they won't fall out an they will stay engaged with the parts that they're supposed to be engaged with.
 
OP
OP
Jaybr

Jaybr

Contributor
Sr. Member
Joined
Oct 8, 2019
Messages
587
They are all new parts, I’m sure vendor would send me new ones if I wanted to wait, but I’m trying to get this latch done so I can move the bronco to the new house (where we’ve already moved in). Also not sure the new parts would be any different than these.

I’m understanding now why I should have salvaged as many original parts as possible from the old body.

I’m not sure I could get wire in there as tight as it is, can’t get fingers in there at all. The other issue is they have to stay centered so they fit through the slot in the bracket, wire wouldn’t help with that.

I could weld up the holes and redrill them the proper size, but that would require I take the parts to the new house where the welder is (3 hours away)

Or I could drill the holes out to fit a larger pin, and my drill press is here with the bronco. (But all my bits are at the new house )


Sent from my iPhone using Tapatalk
 

ntsqd

heratic car camper
Joined
Jan 30, 2005
Messages
5,970
Loc.
Upper SoKA
Pop them loose at the center and pull the assemblies out far enough to get better access.

Those pins don't need to be perfectly centered, just just need to engage both draw-plates - something it looks to me like a wire retainer will do.
 
OP
OP
Jaybr

Jaybr

Contributor
Sr. Member
Joined
Oct 8, 2019
Messages
587
In the open position the pin passes through a slot in the plate, if it’s off center it will hang up. If it slips on the outside of the plate, I won’t be able to turn the handle. If it slips on the inside I’m not sure the latch would retract enough.


Sent from my iPhone using Tapatalk
 

ntsqd

heratic car camper
Joined
Jan 30, 2005
Messages
5,970
Loc.
Upper SoKA
Had to look at it closer. The pin has to go all the way thru that tab to release? What would happen if the pin stopped against that tab without going thru it, is that enough travel to release?
 
OP
OP
Jaybr

Jaybr

Contributor
Sr. Member
Joined
Oct 8, 2019
Messages
587
Can’t say yet, when I had it all assembled briefly, it wouldn’t close. I need to adjust the top a little to make room for the latches.

If I knew it didn’t need to go all the way through, I’d try your method.

Just pulled into Harbor Freight for drill bits, I’ll pick up some safety wire while I’m here


Sent from my iPhone using Tapatalk
 
OP
OP
Jaybr

Jaybr

Contributor
Sr. Member
Joined
Oct 8, 2019
Messages
587
I drilled out the rods, ran a countersink bit on the holes to make it easier to get pins started, and it’s all assembled with no loose pins.

Thanks for the ideas!


Sent from my iPhone using Tapatalk
 
Top