• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Aired-down: how far per one tire revolution?

ntsqd

heratic car camper
Joined
Jan 30, 2005
Messages
5,970
Loc.
Upper SoKA
This came up in a thread not long ago and I got to thinking about it on the drive to work this morning. I recall, dimly, reading about this a number of years ago and it took me quite a while to wrap my head around how it worked then. When @jamesroney posted about this in whatever thread that was I had to re-think my thru it again because it had been so long since I'd last even thought about it. It was not really the topic of that thread and it was left unresolved. I figured that I'd take a stab at trying to lay it out so that hopefully everyone can see what's going on. If I'm not successful then maybe other's postings in this thread will make it so.

The part that only some understood about being aired down is that one tire revolution moves the vehicle a set distance. This distance changes with the tire's size because the tire circumferences are different, but it does not change with tire pressure. That last part causes a lot of people to say "BS! The tire has a shorter radius, so of course it doesn't go as far as when fully aired up."
That's an easy thing to think and it seems to make sense, but it's wrong.

When the tire had it's air pressure reduced that did not also reduce the length of it's tread. I think that this is the key to understanding what is actually happening. The tire tread is a fixed length regardless of the air pressure. If you think of a tank or Caterpillar track, those are both a fixed length. If we change the diameter of the drive & idler wheels we raise or lower the tank or dozer, but we don't change how far one complete revolution of the tracks will move the tank or dozer unless we add or remove some links from the track.

By lowering the air pressure in the tire we've changed the size of the "drive wheel" and altered the torque multiplication ratio, but we have not changed the length of the tread. One revolution of the tire still moves the vehicle whatever the circumference of the tire is. Obviously there can be some slip between the tread and the ground, but the same is also true of the tank or dozer tracks. Let's uncomplicate this sightly by saying that the tire never slips on the ground. This isn't real ALL of the time, but it is real MOST of the time and I hope it makes this easier to figure out.
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
Thanks for bringing it back up and putting the clarity in.
In that other thread you’re referring to, I think someone posted a video that had been done by a guy (possibly in Europe?). I think it was a Volkswagen van where they aired the tire down and with chalk marks on the ground and the tire, proved that it doesn’t change the distance traveled at all.

So, does that also equate to speedometer error? Which I think was the main subject that brought that up. Or no?
Because you mentioned it changes the torque multiplication seen at the other end, so what about the reading seen by the speedometer from any potential change and speed of the shaft inside the transfer case?
So how do we test that?😉😁
 

bmc69

Contributor
Bronco Guru
Joined
Jun 11, 2004
Messages
12,015
All that aside...airing down to 5 psi in my IROKs sure made one heck of a difference on how well they grip rocks. ;-)
 

JB Fab

Sponsor/Vendor
Bronco Guru
Joined
Mar 21, 2004
Messages
1,518
Interesting.... I remember back in the 90s a whole bunch of NY taxi drivers getting prosecuted for lowering their tire pressure to make more $. It would be interesting to see the data brought by the prosecutor...
 
OP
OP
ntsqd

ntsqd

heratic car camper
Joined
Jan 30, 2005
Messages
5,970
Loc.
Upper SoKA
One revolution is one revolution. The tread length is fixed. Lower air pressure operated at speed puts a lot of heat into the sidewall. One tire up and the other tire down wants to steer the vehicle or over-exercises an open diff, but that is due to the difference in drive ratio from one side to the other and not the distance each travels per revolution.
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
Understood. But does “drive ratio“ have any effect on the speedometer reading? In spite of the revolutions per mile staying the same?
Or are those two things the only things to consider? Speedometer readings and revolutions per mile being a hard pair so to speak?
 
OP
OP
ntsqd

ntsqd

heratic car camper
Joined
Jan 30, 2005
Messages
5,970
Loc.
Upper SoKA
If the axle shaft is going the same RPM and the tire is traveling the same distance per revolution then for there to be a difference the tire would need to be slipping on the pavement.

Maybe this will help; when the formula is assembled to calculate the conversion from engine RPM to vehicle MPH the tire's diameter is only used to calculate the circumference of the tire. The circumference of the tire is what is important to the calculation, not the tire's diameter or radius. Physically measuring the tire usually results in a small error because the slight sidewall bulge results in a radius that is shorter than actual. Better is to look up that tire's mfg's spec page and use their diameter (or radius) to calculate the tire's circumference.
 

rcmbronc

Contributor
Bronco Guru
Joined
Dec 15, 2003
Messages
2,778
Loc.
Tomah WI
What if the crown of the tire has a larger circumference then the edge of the tire. When aired down running on the edge of the tire with a lower circumference. Not sure the tire can deform that way but just for thought.
 
OP
OP
ntsqd

ntsqd

heratic car camper
Joined
Jan 30, 2005
Messages
5,970
Loc.
Upper SoKA
The length hasn't changed, the slightly longer crown of the tread is still that length.
I'm sure that with a tire like that there will be some slippage and that slippage may not be uniform across the width of the contact patch. Perhaps there always is unless you run them at some crazy high pressure. Air down such a tire enough and I think what will happen is that the longer center of the tread will 'cup' such that the resulting tire track on the ground will not show contact in the center.
 
Last edited:

Yeller

Contributor
Bronco Guru
Joined
Mar 27, 2012
Messages
7,692
Loc.
Rogers County Oklahoma
If I could just get a few days at home that weren’t booked to the hilt, I think it would be a fun Sunday afternoon project to prove. I know from using my GPS Speedo to compare to my trucks Speedo theirs no perceptible difference between the digital GPS and the mechanical gauge whether aired up to 25 psi or 10 psi

I do seem to remember a noticeable difference when I ran bias ply tires.
 

Broncobowsher

Contributor
Total hack
Joined
Jun 4, 2002
Messages
37,111
More fuel for the fire
Take an aired down tire and roll it over clean white concrete. You leave a tire mark. That tire mark is from the tires slipping on the ground. Rubber flexes, and slides.
 
OP
OP
ntsqd

ntsqd

heratic car camper
Joined
Jan 30, 2005
Messages
5,970
Loc.
Upper SoKA
I would suggest that such marks are from the squirm of the blocks of tread as they get pushed slightly sideways into making contact with the ground, and then get pulled slightly sideways as they're pulled away from the ground.

In any case, those marks do illustrate that tire contact with the ground is not always 1 to 1, but that the slippage is not a lot either or those marks would be considerably more blurry than they are. This introduces a small error, maybe a couple percent at the most. Which is why I suggested that it be ignored and to, at least in the beginning, assume that the tires do not slip. If only to make it easier to grasp the basic idea before considering all of the little nuances.
 

Broncobowsher

Contributor
Total hack
Joined
Jun 4, 2002
Messages
37,111
Speaking of tread block squirm...
Many years ago I was bombing my motorcycle down a dirt road. 650cc pinned wide open on the flat. Road went to pavement. As it did so the speedometer picked up a couple numbers (front wheel) and the tach dropped a little (rear wheel). The difference between tires sort of gripping the ground and strongly gripping the ground.

And years before that, had a delivery job with O'rielly's when they expanded from Springfield into KC. The little S10 trucks were no power house, but the tires were tiny as well. That summer was big road construction in town. I could look in the rear view mirror and see my tire marks. Not spinning, but the tread blocks were squirm enough to nudge the freshly rolled asphalt. Every gear shift the tread marks would stop.

I recall a spec of ~10% slip is the ideal level for traction.
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
If I could just get a few days at home that weren’t booked to the hilt, I think it would be a fun Sunday afternoon project to prove. I know from using my GPS Speedo to compare to my trucks Speedo theirs no perceptible difference between the digital GPS and the mechanical gauge whether aired up to 25 psi or 10 psi
No need to prove it to us anymore. I don’t think. If you didn’t see a difference in the speedometer with those different pressures, then it probably doesn’t make a difference. As most have been saying.
But yes, it would still be fun! :)

Hopefully you’ll get that little extra time anyway.
Besides, times spent on the Bronco are usually good times.
Even if it’s just airing up and airing down!
 
Last edited:

Broncobowsher

Contributor
Total hack
Joined
Jun 4, 2002
Messages
37,111
6 PSI is good for about 3 revolutions in one mile. That is in normal size tires. Don't know what modern large tires will do.
25 years ago I was doing new car testing and needed to force out of balance tires to go into and out of phase.
 

jamesroney

Contributor
Bronco Guru
Joined
Sep 11, 2007
Messages
2,612
Loc.
Fremont, CA
Speaking of tread block squirm...
Many years ago I was bombing my motorcycle down a dirt road. 650cc pinned wide open on the flat. Road went to pavement. As it did so the speedometer picked up a couple numbers (front wheel) and the tach dropped a little (rear wheel). The difference between tires sort of gripping the ground and strongly gripping the ground.

And years before that, had a delivery job with O'rielly's when they expanded from Springfield into KC. The little S10 trucks were no power house, but the tires were tiny as well. That summer was big road construction in town. I could look in the rear view mirror and see my tire marks. Not spinning, but the tread blocks were squirm enough to nudge the freshly rolled asphalt. Every gear shift the tread marks would stop.

I recall a spec of ~10% slip is the ideal level for traction.
I'll bet you've seen plenty of fresh motorcycle tracks in mud? A knobby motorcycle front tire makes a perfect impression of every nub in the mud.

Consider tire tracks from a car rolling in fresh snow? You can easily see the tread blocks, and every detail of the tread pattern. Looks just like you stomped them with your new shoes. (remember the old "waffle stomper?"

Rolling tires don't squirm, or slip much. Slipping tires squirm. Slipping, squirmy tires make more grip. Tires that slip, squirm. and make more grip wear out very fast on pavement.
 

AZ73

Bronco Guru
Joined
Mar 28, 2012
Messages
3,813
Uggg. We just went through this on another thread. You will lose 1-3% of your travel distance. The idea that the circumference of the TIRE off the ground doesn't change doesn't mean the EFFECTIVE circumference due to a flat contact surface is the same distance. Static radius (when you're calculating the circumference of the tire) is not the same as effective radius (the rolling circumference). The tank tread comparison is apples to oranges EXCEPT when a tank turns because the tank tread doesn't flex sideways and it's track doesn't compress. When a tank turns the outside tread moves normally but the inside tread travels a shorter distance. How? It's rotating at a slower speed AND it slips (called "scrubbing") on the ground allowing it to travel a shorter difference even though the circumference of the tread hasn't shortened. Tires do this when they're going straight. They slip/scrub slightly due to compression. The distance of an arc is longer than the distance of a line and the tire is traveling along a line at the contact patch. The contact patch line is 1-3% shorter than the arc. Even though the rim has rotated a full circle, the tread surface has not moved one full circumference relative to the ground — part of that rotation was used up flexing and recovering rubber in the contact zone. It's why tires are made of rubber. The contact patch area, where the tire is flattened, does not contribute fully to forward motion — that section of tread is being compressed when it first hits the ground, and stretched when it lifts off. It doesn't just roll with it's same shape. It's compressed (shortened) when it enters the contact patch, then is stretched (lengthened) when it leaves the contact patch. The contact patch is moving slower than the rest of the tire because it's moving in a straight line instead of an arc. It does it by compressing the tread (and thus shortening the overall circumference) along the contact patch.
Airing down will drop it ANOTHER 1-3% because the contact patch is now larger. More flat surface (assuming you're on a flat surface) and more loss of circumference because the contact surface is deformed and pushed into the tire when going over a boulder, shortening the circumference.

If this is still confusing, think about a top fuel dragster. It's the extreme opposite of what's happening. When it's at the starting line the tire is 36" in diameter When it's at the end of the run, the centrifugal force stretches the tire to almost 46". Part of that is the pulling in of the sidewalls (the tire gets narrower) and the rubber on the centerline stretches all increasing the diameter. On a street car at the contact patch the sidewall gets fatter and the the rubber compresses (shrinks) decreasing the circumference.
 
Last edited:
OP
OP
ntsqd

ntsqd

heratic car camper
Joined
Jan 30, 2005
Messages
5,970
Loc.
Upper SoKA
Ugh, we still haven't gotten it across. The tire tread is a fixed length, it does not matter what the radius of rotation is, a tire of X diameter will have a tread length of X*PI. One rotation of the tire is one circumference worth of distance traveled. How can it be any less?
 
Top