• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Twin Stick cutout no-body lift

bronco t

Contributor
Sr. Member
Joined
Jun 28, 2010
Messages
799
Loc.
San Diego CA
I got the JB twin stick for the J shift from Santa (I love her), and was wondering how the heck does one cut the paddles and install the shifter on an EB with no body lift. I am not a fan of cutting the side of the tunnel out as this will undoubtedly create a re-seal issue, and look like hell because my floor board is lined and faded, and anything new would not match. I might consider an vendor made tunnel cover if I have too.

Also, it appears that the stock shift linkage is encased in a rubber boot (of sorts), and doesn't want to come out cleanly. Should I cut the boot out? I have entertained lowering the tcase and trans, but the engine will more than likely need to move down as well. Which makes this a genuine PITA install.

Anyone a install write up for a no-body lift install?
 

moses_m

Full Member
Joined
May 5, 2013
Messages
262
J shift

I just did this install on my 71 but I did cut from the top. Here are the directions I used.
 

Attachments

  • 8555 08-08-06.pdf
    319.3 KB · Views: 108

Viperwolf1

Contributor
electron whisperer
Joined
Aug 23, 2007
Messages
24,451
I recommend cutting the side of the tunnel. It will help when installing the new shifter or if you ever need to remove the tcase. Make a cover that is slightly larger than the hole and screw it down. You could even coat it to match your floor.

Use a cutoff wheel on a dremel to cut the flags. The instructions above don't tell you to cut the rear rail flag but if you don't you won't have front-high range/rear-neutral.

I used to problems with the shifter bolt (the allen headed one) backing out after a while. I finally drilled the bolt head so I could safety wire it. I recommend that too.
 

fastback

Jr. Member
Joined
Feb 18, 2005
Messages
147
Loc.
Asheboro, NC
I did this! It is a pain but I am glad I did it the hard way and did not cut the tunnel. I took the transfer case skid plate, the front drive shaft,and the crossmember support that hold the transfer case up. This gave me just enough room to get an angled die cutter to cut the flags from underneath. I had to get a small disc attachment for the angle die cutter it was probably around a 3" or 4"wheel.
It takes a lot of trial and error to get up around the transfer case to get all the bolts in place and tightened. The other problem I had was that
The JB kit I got did not have the correct bolt for the J shift in it. I think it takes a 7/16 fine thread. I can't remember the length but it is critical so it does not come in contact with the tunnel cover underneath.
Good luck!
 

oldcarguys

New Member
Joined
Feb 17, 2013
Messages
33
Loc.
North Florida
just did the JB Twin sticks today, sent the wrong bolt in my kit also, it takes a 4 1/2 , 7/16-20 fine tread, but I actually used a 5 ", 7/16 bolt, it worked ok, there is room, on the passengers side for the extra 1/2 of length. A Nut/Bolt supply house was open today, since you wont find a 7/16 , 4.5 ", or a 5" bolt at, any hardware store,,,
 

cs_88

Contributor
Bronco Guru
Joined
Jul 28, 2005
Messages
1,324
Shouldn't need to cut the tunnel to install the JB sticks on a J case with no BL if you don't want to. Mine fit fine with no cutting.
However, I'm sure cutting the flags with the T case installed is a real PITA.
Good luck.
 
OP
OP
bronco t

bronco t

Contributor
Sr. Member
Joined
Jun 28, 2010
Messages
799
Loc.
San Diego CA
It's the PITA part that will be the challenge. Viper may have predicted the future, and that is to cut the tunnel! Luckily my son left his HF shear / break at the house to bend up a tunnel cover. Thanks all.
 

yewhi

Sr. Member
Joined
Mar 23, 2011
Messages
368
Loc.
San Diego
It's the PITA part that will be the challenge. Viper may have predicted the future, and that is to cut the tunnel! Luckily my son left his HF shear / break at the house to bend up a tunnel cover. Thanks all.

Might be able to save you the trouble. I have a WH tunnel cover I bought a few years ago and never used when I did this. It is yours if you'd like it (provided i can find it). The link to the part is below.

http://www.wildhorses4x4.com/product/Twin_Stick_Tunnel_Cover

If you're interested let me know and we can work out a way to get it to you.
 
Top