• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Fun write up on dual batteries

AxlesUp

Sr. Member
Joined
Dec 21, 2001
Messages
424
Loc.
Collierville TN
just to add to it you can get a $20 200-300 amp golf cart solenoid that's rated for continuous duty from the "tribes of amazon"
 

Broncobowsher

Contributor
Total hack
Joined
Jun 4, 2002
Messages
37,114
8 gauge wire for a 60W solar panel? Does he know that the output of that panel is less than 4 amps? This guy loves to way oversize his wiring. He knows enough to make it work, he also knows enough that if you use really heavy wire it won't overload. But he doesn't have a clue how to properly engineer the wiring based on the electrical loads. Just stupid oversize it and it will be fine.
 

bronconut73

Bronco Guru
Joined
Aug 7, 2012
Messages
9,919
I have been guilty of over gauging my wiring before too.....

Smart enough to want to over do it but not smart enough to know when to stop.
Lol
 

ntsqd

heratic car camper
Joined
Jan 30, 2005
Messages
5,970
Loc.
Upper SoKA
The reason for large gauge wire on a solar panel feed is voltage drop, not ampacity. That is just lost power that was paid for in the panel(s). It does seem silly until you do the math and then it's not so silly after all. PWM controllers benefit less from higher voltage than do MPPT controllers. Go at solar like it's "regular" DC power and you will have a poor, under-performing system.

Some light reading on solar:
https://handybobsolar.wordpress.com/the-rv-battery-charging-puzzle-2/

That said, the reason behind "meh" is the use of 1960's "stupid" technology and the fanboys are applauding him for it. There are better and smarter solutions out there that aren't $300. Search "Voltage Sensing Relay" or "Automatic Charge Relay." Hell, search it on that forum as I've posted about them repeatedly there.

The recently unfortunate thing is that Blue Seas has bought BEP Marine and has done to them what Mallory did to Accel, dumbed-down their offerings. Worse, they've reduced where the BEP product can even be purchased from.
 
OP
OP
lonesouth

lonesouth

Contributor
Bronco Guru
Joined
Dec 18, 2003
Messages
5,048
i was looking at an ACR, but from what I recall, the blue sea ACR wasn't particularly cheap...
 

ntsqd

heratic car camper
Joined
Jan 30, 2005
Messages
5,970
Loc.
Upper SoKA
Normal retail on the BEP VSR's was about $90 from places like Del City Wire or Waytech Wire. Now I can't find them online anywhere except West Marine.
This is about twice the ampacity needed on most vehicles, but I'm not finding the 60A-70A ACR/VCR's that they used to offer:
http://www.westmarine.com/buy/blue-...ual-sensing-automatic-charging-relay--8646283
$100, so more than a simple & crude constant duty solenoid but a good constant duty solenoid is more: http://www.westmarine.com/buy/blue-...solenoid-switch-with-coil-economizer--2012425

A little deeper searching found this: http://www.westmarine.com/buy/marinco--digital-voltage-sensing-relay-dvsr-12-24v--14152185 better at ~$90
or this http://www.westmarine.com/buy/marinco--digital-voltage-sensing-relay-dvsr-12-24v--14152185 at $88
Better, at $83: http://www.westmarine.com/buy/blue-sea-systems--mini-automatic-charging-relay--14152557

I prefer combos like this http://www.westmarine.com/buy/marin...ingle-engine-with-two-battery-banks--14152193 at ~$165 or this http://www.westmarine.com/buy/blue-sea-systems---add-a-battery-dual-circuit-system--8646275 at $143 or this http://www.westmarine.com/buy/blue-sea-systems--mini-add-a-battery-system--14152565 at $115 because they allow self jump-starting and any other manually combined battery needs.
 
Last edited:

chuzie

Bronco Guru
Joined
Jul 21, 2006
Messages
2,761
This should make a few of you vomit. ;-) Totally guilty of over engineering.

C360_2015-07-20-10-23-02-125.jpg
 
Last edited:

chuzie

Bronco Guru
Joined
Jul 21, 2006
Messages
2,761
3 functions.

In AUTO, with the ignition on, the batteries are tied and charged by the alternator.

In TIE, I can force them together, even with the ignition off (or dead), in the event I need to utilize the second battery for a jump start with the primary battery dead.

In ISO, I can force them to be separated if I want to protect one of them from draining (long term use of stereo, lights or winch with the engine off).

I use the same Cole Herese solenoid as the write-up linked in post #1, but I use two instead of one. Two reasons: Distribute high amperage during starting and winching operations as well as provide a level of protection, should one of the solenoids fail.

The red LED is a dummy light and indicates when the batteries are TIED. Leaving the system TIED could potentially lead to a complete system drain if I leave something turned on for a long period of time.

The orange LED indicates when the batteries are ISOlated. Again, a dummy reminder light that the system is in a mode other than AUTO and I am not charging my second battery.

It works great, just a bit more complex than other stuff out there. If you see any room for improvement or have suggestions, I am eager to listen.

It's a crappy picture but you can zoom in and see more detail.
 
Last edited:

ntsqd

heratic car camper
Joined
Jan 30, 2005
Messages
5,970
Loc.
Upper SoKA
Ideally in the Auto mode the second battery would not be connected to the charging system until after the starting battery has reached a full state of charge. It obviously works as-is and Lord knows there are many systems out there like it, I'm only pointing out what I understand to be ideal in terms of best battery practice.

Which is where the ACR & VSR's come into play because that is what they do. I prefer a manual, marine type battery switch to do the combining so that it is a deliberate act that I'm not likely to forget to return to normal once the situation is fixed but that is personal preference.

Those solenoids are rated for 80A, so doubled they're good for 160A, which if all of the starting current has to flow thru them it isn't enough ampacity. It is close to enough (I call 200A enough for an SBF) and in all but the worst case scenario they'd likely be fine. FWIW that $200 cont. duty solenoid linked above is rated for 250A continuous and 1000A intermittent.
 

chuzie

Bronco Guru
Joined
Jul 21, 2006
Messages
2,761
That makes sense. I guess I will have to make sure to keep them isolated until the primary fully charges after a jump. Didn't think about that before. Thanks.

The Cole 24213 is a 200A continuous. I thought that was in that write up but may be wrong.

The one thing I am lacking is fuses for each battery. It's on my to do list though.
 

chuzie

Bronco Guru
Joined
Jul 21, 2006
Messages
2,761
I like those a lot. Wish they offered something in 500A though. Otherwise I risk blowing on a hard start or winch pull. I have the deep blue sea 500A ANL fuses but haven't found a good way to mount them yet with the large battery cables yet.
 

ntsqd

heratic car camper
Joined
Jan 30, 2005
Messages
5,970
Loc.
Upper SoKA
Can run them in parallel like you did the solenoids to increase the amperage, but I think that I'd route starting current (only) around them instead.
 
Top