Search results

A set of used JBS 1 1/2" shorty header. I think titanium colored coating. Fit really nice on my 351. Includes bolts. $150 shipped lower 48. rcmbronc@gmail.com

I have been in the process of doing research on a 408 stroker motor. Have a late roller block and looking at parts. Now thinking about a 427 stroker. Not much more money really. Thinking a Dart SHP block with a 4.0 stroke x 4.125 bore assembly. Anyone built one who did not like it and would...

Starting to put together parts for my 408 stroker. I have searched and just looking for some additional info. Looking at some Eagle kits. I am not sure about the hyper pistons. Pretty sure I want forged. What I am wondering is if I should have a forged crank or is the CI ok. Not going to be...

Thinking about putting in an Atlas 2 speed TC. Any suggestions best place to buy from? I have a 4R70W and I assume the best would be to get one that adapts to that tranny then I can ditch the D20 adapter. Also suggestions on output yokes?

2000 Jeep Wrangler. Soft Top, 99,500 miles. 4 cylinder, 5 speed. Aluminum Wheels. Runs well. Good condition. Some light surface frame rust, nothing bad. Some rust on the front fenders, shown on pictures. Also one small spot on the windshield frame. 4 wheel drive works good. New front brakes and...

I need some help with some advice to get rid of the rear roll oversteer. Here is my 4 link calc. I cant seem to figure out what I need to change to get rid of the over steer. I am assuming flatter lower links but dont want to drop the front mount and just moving the rear mount up and in front of...

Looking for pics of what others have done for an exhaust system with a rear 4 link. I have W shorties. I had a Magnaflow 2 into 1 2.5 x 3 muffler. Not much room under there now for any muffler. Only have a 1" body lift so not enough room to run the pipe above the frame and mufflers outside of...

Think I am using GM rear calipers on my new floater. They are the calipers with a 10 mm fitting. Looking for some flexible hoses that will work for this. Anyone maybe know a local part number or application to look at? The calipers are off a 1980 Chevy K20 but those are not really what will work.

I have the 9" ford rear end out of my Bronco. Yukon 31 Spline axles drum brakes. No carrier or center section and no gears. Will separate. $300 for all. $175 axles.

Putting my floater rear end in my truck. I am using Schreiner 35 spline floater hubs with disc. I need to add calipers and brackets. I am looking at 4 piston Wilwood calipers with 1.75" pistons. Could also do a 3.15" GM single piston caliper. Any suggestions or others. Cant do a Explorer parking...

Trying to decide which route to go with for 35 spline floater ends on my 3.5" ford nine inch housing. I have been looking at Curries extreme unit bearing ends and also Schreiners hubs. Also at Dana 60 hubs. I like the unit bearings but looking for any feed back...

Set of 4 wheel spacers. 5 x 5.5 - 5 x 5.5. 1 1/2" Thick. No nuts included. $75 shipped. rcmbronc@gmail.com

Looking at this EFI system. Anyone have any reviews, opinions and experience? Seems decent price for all included and with timing control and multi port. https://www.summitracing.com/parts/edl-32420 http://www.edelbrock.com/automotive/mc/efi/

I have a WH 4 1/2" lift in my truck that I am replacing. It has 11 leaf rear springs. I removed the third leaf from the top to drop it a bit. Also one of the bottom short leafs broke. Includes poly bushings. $200 Front WH 4 1/2" coils Red good condition SOLD Brand new Front WH 3 1/2" coils...

Anyone have some pics of how they mounted front coil over shocks. I have a pretty good idea how I want to build some hoops but looking to see what others have done. Thanks,

I am going to be getting some 17" aluminum bead locks soon here. Looking for opinions and if anyone has had any issues with these. Method wheels 101 https://www.methodracewheels.com/collections/race-wheels/products/truck-beadlock-machined Fuel Anza...

Looking for some pics of Broncos on 37x12.5x17 tires. If you have any can you please post some. Trying to decide from 35 to 37. Thanks,

Looking for new tires. Probably 35x12.5x17. I want a MT aggressive tire but not terrible on the road. Looking at the BF Goodrich KM2 MT or maybe the Yokahoma Geolander MT. Dick Cepek has a decent Extreme Country tire also. Also maybe Maxis Trepador. Any suggestions? Might go 37 but probably not.

I put the Bronco on a set of race car scales last night and just thought I would give the results. The total weight is 3986# LF 1178# RF 1271# LR 801# RR 736# My truck has not top, full cage, tube doors. All steel with no front inner fenders. Just thought I would post for information. I did...

Looking at these wheels. http://walkerevansracing.com/products/88-17x85-5x55-pattern-bead-lock.html It looks to be cut on the back side of the wheel with a recess to slip over a hub. Not sure how big a EB front hub is. Other thing is I have rear drum brakes so kind of looks like this will not...