Search results

Looking at maybe a soft top. Rampage. I dont usually run with doors but I use tube doors. A top would be nice. How bad do they flop around at highway speed without any doors?

Well I am building a new 408W. I sold my 427 and wanted to try a different build. Here is what I am looking at so far. Late factory roller block Bore and hone with deck plates. Ohio Crankshaft 4.0 stroke x 4.030 stroker kit. Forged 4340 crank, H-Beam rods. Forged SRP pistons. 10.5-1...

Has anyone ever installed an aftermarket crank trigger on a 351W with the standard water pump and front dress. I am building a new 408W. Using a Holley Terminator X ECU. Holley EFI Hi Ram intake. Need a cam sync signal and ignition signal. There is not a ton of room under the Hi Ram intake for...

Putting together a new 408. Motor will be roller block with an Ohio crankshaft forged rotating assy. Edelbrock Victor Jr heads with about 10.5 compression. Hydraulic roller cam (not picked yet). Was going to use Edelbrock Pro Flo EFI but can't bring myself to EFI I can't laptop tune. My last 427...

3.0" Diameter used coil over springs. Very good condition but they have been slightly used. 2 - 14" x 450 LB King 2 - 14" x 100 Lb Eibach 2 - 16" x 300 Lb King $45 each shipped.

Looking to build some interior panels for my Bronco and other projects. Looking for any advice on a bead roller to get. Can be manual but I may go with electric motor. Anyone got any help?

Just like new Abu Garcia REVO Toro Rocket low profile bait casting reel. 7.6 - 1 ratio. Used once. Comes with three handles. Loaded with 80# Power Pro. Rod not included. Asking $225 shipped.

I just finished building this engine and getting it running in my Bronco. It is awesome and makes great power. No complaints on the engine. Just thinking I want to build another motor for it. Ford Small Block Windsor 427 CI Ohio Crankshaft Short Block Dart SHP Block 9.5 x 4.125 bore Ohio...

I have 1 3/4" fender well headers and dual 3" exhaust under each floor board. I have these mufflers. https://www.summitracing.com/parts/wlk-17657 Not a good choice. Way too loud. i have room for better mufflers so I need a much quieter set up. Any suggestions?

Looking to upgrade to a new larger rear tank. Looking at the Toms 23 gallon tank or the Wild Horses tank. Any opinions? The WH tank is SS and a bit more expensive. I will be putting in an in tank pump. I have the Holley sniper fuel pump system that I will be using. Any good or bad on each of...

Power Products long hole design fabricated valve covers. Small Block Ford. Couple light scratches. Never ran. Will not fit a Bronco with 1" body lift. Slight interference on drivers side fire wall. May with a 2". $75 shipped lower 48

Wild Horses Black Anodized crank pulley. 3 and 4 bolt pattern. Put on once and then removed. Never run. $75 shipped lower 48.

Trying to decide if what TC to run. Got a good Dana 20 in the truck now. 4R70W, 5.13 gears and 35" tires. Not heavy crawling but decent trail running. Trying to decide to go with an Atlas or modify the D20 with HD output. Truck is pre runner style build with a healthy 427 probably 550-600 hp...

So I have 1 3/4" fenderwell headers. All is installed and the steering shaft is hitting the headers. I have the aftermarket lower shaft with dual u joints. I am going to try to move the motor but I dont think it would be enough. Anyone ever had to move the steering column? Maybe just the lower...

Looking for another Bronco project near WI. Dont want a complete rust basket case but some OK. Can be cut. Let me know if you have anything. Rob Carlson rcmbronc@gmail.com 608-343-0713

Anyone tried this chassis paint. Steel-It. Seems like a lot of off road racing support.

I am looking for an angle Astro hydro boost bracket.

I have a Ford 351W F4TE Roller Block. Standard bore. Seems to be in fine condition, dirty. Includes hydraulic roller lifters, retainers and spider. Will also include stock rods, pistons and crank. Asking $200. Really dont want to ship.

Is an aftermarket oil pan required for a 4.0" stroker motor. Or can the 351W pan the vendors sell be used?

I have an almost complete 351W motor. The short block is mid 80's Ford truck. Rebuilt with new rings and bearings, standard bore about 8 years ago. Probably has about 500 miles on it. 69 heads with roller tip rockers. Motor runs well, slight tick at start up. Includes everything except valve...