• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Search results

  1. JSBX

    Cowl Hood

    Anyone running a Bronco Hut cowl hood. If so how is the fit and finish? Any draw backs? Pictures of it on a Bronco would be great. Thanks James.
  2. JSBX

    Big Problem with torque converter bolts

    This want help with the torque converter nut problem but when I removed the C-4 from my last Bronco I took some long wires and installed a push button switch on one end and hooked the other ends to the battery and solenoid. Disconnect the coil wire so the engine want try to start. You can bump...
  3. JSBX

    Nitrogen Hood Shocks recommendations

    Hood Duffs.They seem to brace the hood better than some of the other vendors.
  4. JSBX

    4r70w to Atlas help!

    Cross member For the ones that are following this thread. BC Broncos has a cross member that will work with a 6R80 or 4R70W. Dana 20 or atlas. This is per Jason at BC. Since I am not much of a fabricator or welder I ordered one today. Thanks to all the ones that responded to this thread. James.
  5. JSBX

    4r70w to Atlas help!

    In my 74. After I figured the cost of low gears, heavy duty output and an adapter the cost for the Dana 20 work was just a little less than an atlas. So I bit the bullet. I had a 351 roller built local using the GT 40 heads that I had. I have all my old stuff out and trying to get this done...
  6. JSBX

    4r70w to Atlas help!

    Got me concerned now. I will call Bronco Hut tomorrow and talk with them about it.
  7. JSBX

    4r70w to Atlas help!

    I am getting ready to do the same thing when my Atlas arrives in a couple more weeks. Has been 6 weeks since I ordered it. I bought a cross member from Bronco Hut for the 4R70W swap.
  8. JSBX

    Temp Sender Replacement

    Could be the wire from the sender to the gauge is broke or corroded. The first thing I would check is the connector at the sending unit then connector at gauge or run a jumper wire.
  9. JSBX

    Holley Sniper + Hyperspark Problem

    Check your grounds on the ignition system. My son had a similar problem with his and it turned out to be a bad ground.
  10. JSBX

    97 Explorer Engine Rattling

    We just ran into this same problem on a rebuilt explorer engine. Turned out to be a pulley on the front dress.
  11. JSBX

    best place to buy Holley sniper

    I have never seen people from Holly at a Bronco event donating parts for raffles but I have seen vendors donating there parts, time, making videos for the Bronco community and delivering parts to save on shipping. If it wasn't for our venders there would be very few Broncos on the road. I have...
  12. JSBX

    best place to buy Holley sniper

    Some of the Bronco venders sale the Holly Sniper. You can not go wrong buying from a vendor. Not only do you get good service, tech support and friendly people you can talk to about a problem,you also support people that support the Bronco community. Holly has a good tech support system for...
  13. JSBX

    Rough idle/crankcase pressure

    I had that happen on a 79 Ford F-150 once. I found the PCV valve, the line from PCV to the EGR plate and the EGR plate completely plugged up with gunk. Cleaned them all out and cured the problem.
  14. JSBX

    Blueprint Accessory Drive

    Check out BC Broncos. They have an Explorer type front dress kit with everything you need.
  15. JSBX

    manual Power steering unit.

    I sent you a PM. It is on its way. Should be there in a couple of days.
  16. JSBX

    manual Power steering unit.

    I have one in the scrap pile. It came off a 72 but the PO welded the pitman arm on it but should work for what you need. PM me your address and I will send it to you. You want owe me anything. You may have something I need one of these days and we can trade out.
  17. JSBX

    LA Need parts for 78/79 Bronco

    That is an option but they sell just the shell. By the time I bought all the parts for the inside it is going to get expensive but thanks for the suggestion. I may have to go this route if I don't find a used one. They don't carry the half cab conversion any longer. They had trouble with the...
  18. JSBX

    Trans Cooler and A/C Condenser, Enough Real Estate for Both

    Cooler Hey Billy. We just put an Explorer motor and transmission in my son's bronco. He has a a/c condenser and we installed a transmission cooler and had plenty of room. I can get pictures when I get home from work next week.
  19. JSBX

    LA Need parts for 78/79 Bronco

    It did not have a tailgate when I got it but thanks for the information. I will do some research and see what I can make work
Top