• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Holley Sniper + Hyperspark Problem

BulldogBronco

Full Member
Joined
Nov 13, 2018
Messages
155
I put a holley sniper on my 302 a couple of months back and recently added the hyperspark ignition system which included the coil, the distributor and the ignition. When i drove it home from my mechanic in stop and go traffic, the RPM's went low and it died on me. It started right back up and I had no more issues. Then, I went to drive it yesterday and it struggled to start and ran awful. It was backfiring, stalling, etc. Even after I got it running after I let it run for awhile, it would lose power going down the road and seem like the throttle was pulling back. I'd like to try and fix it myself rather than get it towed to the mechanic, does anyone have any experience with the Sniper EFI and the Hyperspark ignition system? Or can anyone tell me what the timing should be at start (currently set at 15) and Wide open throttle (currently set at 32), and cruise (currently set at 35 or 36?). I checked the firing order and it is right. Could the issues be caused by the distributor being installed on the wrong stroke? Any ideas on why it would be running rough or tips on how to tune the system?
 

Broncobowsher

Contributor
Total hack
Joined
Jun 4, 2002
Messages
37,112
I would be watching the hand held controller. What you describe sounds more like a fuel pump going out.
 
OP
OP
BulldogBronco

BulldogBronco

Full Member
Joined
Nov 13, 2018
Messages
155
Thanks for the reply, when I installed the Sniper system in April, I also put in a 23 gallon M1A1 tank from Wild Horses with the in tank pump. Is it realistic it could fail that quickly?

Also, I never had this issue with my old setup which makes me think it has something to do with the new ignition system? As it dies, the air to fuel ration drops on the handheld monitor.
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
Not familiar with the Hyperspark. Is it it's own company, or is that from Holley too?
Are you having the computer control the timing? Sounds like it's currently stand-alone rather than computer controlled.

But yes, even though we've had fantastic luck with our current model of in-tank pumps (several years now) it's never impossible for a pump to fail. Even brand new OE pumps from the various manufacturers fail. I've seen GM, Ford and Toyota pumps fail while still under warranty. And I always like to mention in the eighties we used to hear about Buick owners who bought the Regals with the 3.8 turbo engines running their tanks dry and frying the pump immediately. This was on newer, low-mileage pumps. The more miles on them the more forgiving they were of being run dry. Ever since then I've never run an electric pump dry until I had at least 10k miles on it!

So while it would have been low on my list of culprits, it would not hurt for you to test fuel pressure anyway.

But if the Hyperspark is anything like an HEI you could have some radio noise interference with the ECU.
Got a link to the ignition?

Thanks

Paul
 

bronkenn

Contributor
Bronco Guy
Joined
Apr 27, 2017
Messages
2,717
Loc.
Southeast Ohio
Watch your handheld controller while running and see what the RPM's are doing. If they are all over the place, like really high or zero out then I would suspect EMI (magnetic interference) from the distributor.
 
OP
OP
BulldogBronco

BulldogBronco

Full Member
Joined
Nov 13, 2018
Messages
155
The computer is controlling the timing and here is a link to the hyperspark distributor. It’s all Holley and supposed to make for a seamless install where it all works well together.

https://www.summitracing.com/parts/sne-565-300/

Bronkenn the rpms definitely jump around, even when idling. It will sit in the 800’s and be smooth and then jump to 1200-1300 and then sometimes just drop to 0 and stall. Your emi suggestion sounds like it could be right, what’s the fix for that?
 

Allen_69

Bronco Guru
Joined
May 23, 2001
Messages
1,492
Loc.
Sugar Grove Pa
Have you verified that your running the minimum firmware that supports the Hyperspark ignition system? Verify that the programming change was made so that the system recognizes that it has an different distributer. You could also do a reset so that the ecu would go thru it's initial learn process. It maybe trying to correct back to it's initial settings.
 
OP
OP
BulldogBronco

BulldogBronco

Full Member
Joined
Nov 13, 2018
Messages
155
Allen_69, i verified it's the right version of firmware and it is showing the hyperspark distributor in the handheld device but I could still try and reset the ECU since the distributor and ignition are a later addition from the initial Sniper install.
 

JSBX

Contributor
Sr. Member
Joined
Mar 10, 2010
Messages
652
Check your grounds on the ignition system. My son had a similar problem with his and it turned out to be a bad ground.
 
OP
OP
BulldogBronco

BulldogBronco

Full Member
Joined
Nov 13, 2018
Messages
155
Alright, I will look at the grounds too and at worst, run another one from the frame to the engine.

If it is magnetic interference, does anyone have suggestions on how to fix that? I read some stuff on the holley site about maybe needing a new alternator. Any other areas to troubleshoot?
 

Allen_69

Bronco Guru
Joined
May 23, 2001
Messages
1,492
Loc.
Sugar Grove Pa
Just to confirm, your Pos and Neg is connected directly to the battery as recommended, not to a relay or distribution block.
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
A quick test to see if there is interference is to slip a plate of aluminum or some other material that can block at least most of any radio noise.
Just place it between the distributor and TBI/ECU and see if anything changes.

I'm not sure if wood, plastic, or other materials are workable, or if it has to be metallic.

Paul
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
Actually, metallic sounds good. Ever see pics of the sixties Corvette engines? The regular ones (in other words, not the L-88's and ZL-1's or other top-end performance models) always had those polished stainless, or chromed metal full covers over the distributors and plug wires as they ran across the firewall.

I had initially thought they were just decorative (if a bit silly for that) so I would always put them back on anyway. Besides, that kept it "original" and correct. But all the shielding was actually for the radio.
Apparently the fiberglass body, with the dash so close to the ignition components was not enough to shield things.

But some 18ga tin covers were.

Paul
 
OP
OP
BulldogBronco

BulldogBronco

Full Member
Joined
Nov 13, 2018
Messages
155
Thanks for the idea Paul. Should I try and shield the ignition box and coil too or just the distributor?
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
You have a separate ignition control module? Like an MSD 6 or similar?
How close is the coil to the computer? Is it still mounted to the top of the engine like original, or somewhere else such as the top of the wheel well?

Maybe just shield the TBI itself. Simple and in place, and should cover all bases.
If you know right where the ECU is mounted, maybe just cover that area if it's easier.

But with several people having done this, maybe they'll pop in and tell us just what they did. Maybe the shielding has to cover the sensors as well, in which case you may end up with one of those cool carburetor buckets like were on the Shelby Cobras!
They were probably for both air intake AND under-hood heat rejection.

Paul
 
OP
OP
BulldogBronco

BulldogBronco

Full Member
Joined
Nov 13, 2018
Messages
155
The Coil and the Ignition are both mounted on the passenger wheel well, I spoke with Holley tech support and they suggested the same thing, shield the TBI/ECU and see what happens.

Another question, if that ends up being the issue, what spark plug wires does everyone suggest to best suppress RFI/EMI?
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
All modern street oriented (not solid copper core types of course) plug wires should have sufficient shielding for our applications I would hope.
One of the more popular sets is Ford Racing plug wires. But they're not the only ones. Are yours new or old?
I wonder if you have a leaky one?

There are some sets out there from a couple of the speed companies (like Mr Gasket and Speedway Motors maybe?) that are actually braided stainless along their length.
Probably for the cool look, but it would likely improve heat resistance AND noise output I would expect.

Paul
 
OP
OP
BulldogBronco

BulldogBronco

Full Member
Joined
Nov 13, 2018
Messages
155
Mine were new in April but my hood was cut to fit my old distributor (it was too tall) and there was some slight wear on one of the new wires from rubbing against the metal when the hood closed. We covered it with heat shrink? or something of the like. Could something that small cause the issues?
 
Top