Search results

I am still looking for this this Bronco. If you know where it is, please let me know. Last know location was Ogden, UT.

Thanks for all the replies! I have twin sticks and when I disengage the rear axle and drive only using the front axle the noise disappears. This leads me to believe the noise is rear axle related since the transmission and transfer case were quiet. Guess I need to just pull the rear axle apart...

Recently my 1977 rear axle (9" BB) started to make a noticeable whining noise when its put under a load (ie accelerating, running through gears from a stop, etc.) I checked the fluid and its clean and full. Before I pull the diff, I thought I would check to see what folks think. Is this...

Thank you for the great explanation of the challenge with the AOD. Thats what I suspected and I have been looking at ways to adjust the geometry. I am in the process of planning an engine upgrade and going through the trades. Carb vs fuel injection is the latest. Since I have a 3 year old AOD...

Is anyone running an AOD with either the Holley or Edelbrock fuel injection? Any issues with adjusting the TV cable to get the transmission to shift correctly at the right engine loads?

Still looking. Any sightings?

Bump

Hi-Yes it’s still available.

1967 Intake and Carb thats been sitting on the shelf for 5 years. $100 OBO. Pickup only.

Parts are from a 1967. $200 OBO. Pickup only. Clutch, bell housing, flywheel, bell housing fork, throwout bearing, clutch and brake pedals, clutch bell crank parts, block separator plate and clutch push rod.

Yeah, thats what caught my attention about the 77 housing lingo.

I installed a set of 1977 axles (D44 and 9 inch big bearing) under my 1967 Bronco. The rear axle housing is a Centurion vs Banjo. I read that both housings styles came stock with the 1977. I assume Ford transitioned from the Banjo to the Centurion because it is stronger, but I cannot find much...

I am looking for my previously owned 1971 rock crawler to use for my next Bronco project. Last known location was northern Utah. If you have it or know who does, I am interested in purchasing it.

I am looking for my previously owned 1971 rock crawler to use for my next Bronco project. Last known location was northern Utah. If you have it or know who does, I am interested in purchasing it.

Any idea why oil would be leaking for the fuel pump? Its not leaking from the gasket where it attached to engine, the pump itself is leaking. I replaced the last pump thinking it was the pump, now the new pump leaks. How is oil getting up in the pump? Do I have crank case pressure pushing it in...

Reduced price...

Tom's Bronco Parts polished ceramic long tube headers for a Ford 289, 302 or 351. Used for one year on the road only...approx. 2000 miles. Excellent condition. $300 OBO Cost $425 new... Craigslist Link: https://huntsville.craigslist.org/pts/d/madison-early-bronco-ceramic-headers/7256231436.html

Price reduced. Need to get these parts out of the gargage Clutch, bell housing, flywheel, bell housing fork, throwout bearing, clutch and brake pedals, clutch bell crank parts, block separator plate and clutch push rod. Parts came out of a 1967 Bronco. $250/obo Craigslist Link...

Clutch, bell housing, flywheel, bell housing fork, throwout bearing, clutch and brake pedals, clutch bell crank parts, block separator plate and clutch push rod. Parts came out of a 1967 Bronco. $350/obo Craigslist link below...

Tom's Bronco Parts polished ceramic long tube headers for a Ford 289, 302 or 351. Used for one year on the road only...approx. 2000 miles. Excellent condition. $325 OBO Craigslist link below: https://huntsville.craigslist.org/pts/d/madison-early-bronco-ceramic-headers/7216511940.html