Search results

I'm getting close to starting the 302 in my 1976 Bronco that I have been restoring back to original and have a vacuum line question. The distributor, I'm assuming wants ported vacuum and the 2150 carb has the ported vacuum line on the side of the carb on the passenger side of the vehicle. (see...

I am putting the rebuilt carb and EGR valve base back on and it came with 4 gaskets. 2 thin gray gaskets, 1 thicker black gasket with encased metal and one very thick black spacer type gasket with plastic inserts installed in the 4 holes. See picture with the gaskets laid out as stated above...

I have a question on installing the washer fluid box on my 76 bronco. There are three holes in the tank to bolt to the fender well. I can get the top two holes lined up but the bottom hole is about two inches from sitting flat with the fender well. I can tell all three holes were used as...

I am looking for someone with an original 1976 or 77 bronco to take photos of the engine compartment area. Mainly need wire harness routes, solenoid area etc of the entire engine area. The more pics the better as I am putting things back together following the frame off restoration that started...

I'm installing the rubber floor kit in my 76 and was wondering what you guys do, drill out the holes for the seats in the rubber floor or cut the complete contact surface area out with a razor knife? The reason I ask is because there are double holes close to each other in the seat frame and...

I'm installing my rebuilt heater box and dash in my bronco after being apart for years and am asking how the red and orange wires are orientated on the back of the dash at the high low switch. Can someone post a wiring diagram of this area or tell me which side of the bronco (driver and...

Im installing my Retro Huntington radio in my bronco. The original radio was hooked to power with a yellow wire with thin black stripe that I'm sure is original to my bronco. From Retro I also bought their single speaker that I installed in original location. In their directions it says I have...

Does anyone know where this part goes? I don't remember after 15 years it was apart. It's the only piece I have left to put on somewhere. thanks

I just bought an original Motorcraft DY-893 ignition control module from e-bay. it says he has like 7 left to sell if anyone else wants an original. Here is the link, hopefully it works. 306663776226

I am restoring my 76 Bronco and had been looking for hubcaps like ICON uses on a lot of his builds. I really liked that look with the half moon caps and Wimbledon white rims. I spoke with Jonathon from ICON a long time ago and asked him if I could buy caps like that from him or where he...

Last week I posted that I was looking to buy an original Ford power steering pump for my 76 bronco. Master Chief graciously sent me one but it turns out it is a repop Cardone brand and when I took my pump apart to exchange housings it was not the same. My pump is an original with very low miles...

I am putting together my bronco after a 12 year lapse. Does the pics look correct as far as how the system goes back together? Also I assume this spring goes there somewhere so the emergency brake releases. Does anyone know where it goes too and from? thanks a bunch fellows.

I need help with my restoration I am just closing in on. I have a bunch of these heavy washers that are .180 thick. The outside diameter is 1.300, which is just over 1 1/4. And the inside diameter hole is .450, not quite 1/2. There are 7 or 8 of them. I had all the parts bagged up 12 years ago...

I need an original power steering pump for my 76. I actually dont need the whole pump, but would buy what ever you have as long as it has a non dented outside reservoir. My internals are excellent but I accidentally dropped the pump and dented the outer tin and it deformed the o-ring area and...

I have a 1976 Bronco with original smog pump. Im trying to figure out belt location and sizes of the three belts. I can't find any diagrams anywhere. Mine has the original smog pump and I dont have the old belts. Im assuming that the smog pump and alternator is 1 belt in itself, meaning it...

Can anyone tell me the specs, gear ratio, positive traction on my 1976 with C4 and 302 engine. Here is a pic of the tag on the axle. thanks

I am connecting the original (new nylon) fuel line to the 3/8 rubber lines and was wondering if you just push on the rubber fuel line over the nylon fuel line and put a clamp on it or is there special connectors to use. I was thinking the nylon line may compress after putting the rubber line...

Can anyone with their original distributor and smog equipment please take a look and see how many vacuum lines on the distributor. They have single or dual lines. My 76 I am getting close to finishing had the original distributor replaced with a points set up years ago by the gentlemen who...

Ok so I am finally about to order a Duraspark II distributor for my stock rebuilt 302. Its a 1976 by the way. Does anyone know if it will come with a cast or steel drive gear? Also I am keeping all the original smog equipment. Should it have single or dual vacuum distributor? My original...

Im down to putting the water pump on my stock overhauled 302. Looking for suggestions on what is the best one out there? Is there a superior one or should I just go to the local parts supplier for one. thanks paul